Maskless Process for Fabrication of Ultra-Fine Pitch Solder Bumps for Flip Chip Interconnects

2003 ◽  
Vol 125 (4) ◽  
pp. 597-601
Author(s):  
R. T. P. Lee ◽  
A. S. Zuruzi ◽  
S. K. Lahiri
Keyword(s):  
Failure Mode ◽  
Flip Chip ◽  
Solder Bump ◽  
Low Cost ◽  
High Stress ◽  
Lead Free ◽  
Fine Pitch ◽  
Solder Bumps ◽  
Dimensional Uniformity ◽  
Lift Off

The results of this study demonstrate the viability of a low cost maskless process for the fabrication of ultra-fine pitch solder bumps. The fabricated solder bump arrays have a pitch and diameter of 120 and 70 μm, respectively. Widely used eutectic 63Sn37Pb and lead-free 95.5Sn3.8Ag0.7Cu solders were used to form the bumps. No solder bridging was observed between adjacent bumps, and the solder bumps exhibited good dimensional uniformity. The solder bump to aluminum (Al) pad bond integrity was found to be excellent, as evidenced by the high stress to failure. The failure mode is predominately Al pad lift-off indicating a robust solder bump-pad joint.

Thermally Activated Bumping Process using Sn3.0Ag0.5Cu Solder Powder for Low-Cost Interposers

2013 ◽  
Vol 2013 (1) ◽  
pp. 000420-000423
Author(s):  
Kwang-Seong Choi ◽  
Ho-Eun Bae ◽  
Haksun Lee ◽  
Hyun-Cheol Bae ◽  
Yong-Sung Eom
Keyword(s):  
Screen Printing ◽  
Flip Chip ◽  
Solder Bump ◽  
Low Cost ◽  
Organic Substrate ◽  
Lead Free ◽  
Lead Free Solder ◽  
Thermally Activated ◽  
Fine Pitch ◽  
Free Solder

A novel bumping process using solder bump maker (SBM) is developed for fine-pitch flip chip bonding. It features maskless screen printing process with the result that a fine-pitch, low-cost, and lead-free solder-on-pad (SoP) technology can be easily implemented. The process includes two main steps: one is the thermally activated aggregation of solder powder on the metal pads on a substrate and the other is the reflow of the deposited powder on the pads. Only a small quantity of solder powder adjacent to the pads can join the first step, so a quite uniform SoP array on the substrate can be easily obtained regardless of the pad configurations. Through this process, an SoP array on an organic substrate with a pitch of 130 μm is, successfully, formed.

Electromigration Performance of Flip-Chips with Lead-Free Solder Bumps between 30 μm and 60 μm Diameter

2012 ◽  
Vol 2012 (1) ◽  
pp. 000891-000905 ◽  
Author(s):  
Rainer Dohle ◽  
Stefan Härter ◽  
Andreas Wirth ◽  
Jörg Goßler ◽  
Marek Gorywoda ◽  
...  
Keyword(s):  
Flip Chip ◽  
Failure Modes ◽  
Solder Bump ◽  
Void Formation ◽  
Lead Free ◽  
Large Temperature ◽  
Flip Chips ◽  
Solder Bumps ◽  
Current Densities

As the solder bump sizes continuously decrease with scaling of the geometries, current densities within individual solder bumps will increase along with higher operation temperatures of the dies. Since electromigration of flip-chip interconnects is highly affected by these factors and therefore an increasing reliability concern, long-term characterization of new interconnect developments needs to be done regarding the electromigration performance using accelerated life tests. Furthermore, a large temperature gradient exists across the solder interconnects, leading to thermomigration. In this study, a comprehensive overlook of the long-term reliability and analysis of the achieved electromigration performance of flip-chip test specimen will be given, supplemented by an in-depth material science analysis. In addition, the challenges to a better understanding of electromigration and thermomigration in ultra fine-pitch flip-chip solder joints are discussed. For all experiments, specially designed flip-chips with a pitch of 100 μm and solder bump diameters of 30–60 μm have been used [1]. Solder spheres can be made of every lead-free alloy (in our case SAC305) and are placed on a UBM which has been realized for our test chips in an electroless nickel process [2]. For the electromigration tests within this study, multiple combinations of individual current densities and temperatures were adapted to the respective solder sphere diameters. Online measurements over a time period up to 10,000 hours with separate daisy chain connections of each test coupon provide exact lifetime data during the electromigration tests. As failure modes have been identified: UBM consumption at the chip side or depletion of the Nickel layer at the substrate side, interfacial void formation at the cathode contact interface, and - to a much lesser degree - Kirkendall-like void formation at the anode side. A comparison between calculated life time data using Weibull distribution and lognormal distribution will be given.

Development of Lead-Free Flip Chip Package and Its Reliability

2003 ◽  
Author(s):  
Jeffrey C. B. Lee ◽  
Sting Wu ◽  
H. L. Chou ◽  
Yi-Shao Lai
Keyword(s):  
Failure Mode ◽  
Flip Chip ◽  
Failure Modes ◽  
Solder Bump ◽  
Wire Bonding ◽  
Point Of View ◽  
Lead Free ◽  
Temperature Cycle ◽  
Snagcu Solder ◽  
Temperature Cycle Test

SnAgCu solder used in laminate package like PBGA and CSP BGA to replace eutectic SnPb as interconnection has become major trend in the electronic industry. But unlike well-known failure mode of wire bonding package, flip chip package with SnAgCu inner solder bump and external solder ball as electrical interconnection present a extremely different failure mode with wire-bonding package from a point of view in material and process. In this study, one 16mm×16mm 3000 I/O SnAgCu wafer bumping using screen-printing process was explored including the effects of reflow times, high temperature storage life (HTSL) and temperature cycle test (TCT) on bump shear strength. Furthermore, the qualified wafer bumping is assembled by flip chip assembly with various underfill material and specific organic build-up substrate, then is subject to MSL4/260°C precondition and temperature cycle test to observe the underfill effect on SnAgCu bump protection and solder joint life. Various failure modes in the flip chip package like solder bump, underfill and UBM and so on, will be scrutinized with SEM. And finally, best material combination will be addressed to make the lead free flip package successful.

A novel bumping process for fine pitch Sn–Cu lead-free plating-based flip chip solder bumps

2007 ◽  
Vol 10 (4-5) ◽  
pp. 133-142 ◽  
Author(s):  
Jung-Tang Huang ◽  
Pen-Shan Chao ◽  
Hou-Jun Hsu ◽  
Sheng-Hsiung Shih
Keyword(s):  
Flip Chip ◽  
Lead Free ◽  
Fine Pitch ◽  
Solder Bumps

The Use of Precision Selective Area Milling for Failure Analysis of Flip-Chip Packages

2002 ◽  
Author(s):  
George F. Gaut
Keyword(s):  
Failure Analysis ◽  
Flip Chip ◽  
Solder Bump ◽  
Selective Area ◽  
Fill Material ◽  
Solder Bumps ◽  
Time Required

Abstract Access to the solder bump and under-fill material of flip-chip devices has presented a new problem for failure analysts. The under-fill and solder bumps have also added a new source for failure causes. A new tool has become available that can reduce the time required to analyze this area of a flip-chip package. By using precision selective area milling it is possible to remove material (die or PCB) that will allow other tools to expose the source of the failure.

scholarly journals Demonstration of fine pitch FCOB (Flip Chip on Board) assembly based on solder bumps at Fermilab

2009 ◽  
Vol 4 (11) ◽  
pp. T11001-T11001
Author(s):  
E Skup ◽  
M Trimpl ◽  
R Yarema ◽  
J C Yun
Keyword(s):  
Flip Chip ◽  
Fine Pitch ◽  
Solder Bumps

Quantitative Evaluation of Voids in Lead Free Solder Joints

2015 ◽  
Vol 772 ◽  
pp. 284-289 ◽  
Author(s):  
Sabuj Mallik ◽  
Jude Njoku ◽  
Gabriel Takyi
Keyword(s):  
Solder Bump ◽  
Solder Joints ◽  
Void Formation ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
X Ray ◽  
Size And Shape ◽  
Solder Bumps ◽  
Free Solder

Voiding in solder joints poses a serious reliability concern for electronic products. The aim of this research was to quantify the void formation in lead-free solder joints through X-ray inspections. Experiments were designed to investigate how void formation is affected by solder bump size and shape, differences in reflow time and temperature, and differences in solder paste formulation. Four different lead-free solder paste samples were used to produce solder bumps on a number of test boards, using surface mount reflow soldering process. Using an advanced X-ray inspection system void percentages were measured for three different size and shape solder bumps. Results indicate that the voiding in solder joint is strongly influenced by solder bump size and shape, with voids found to have increased when bump size decreased. A longer soaking period during reflow stage has negatively affectedsolder voids. Voiding was also accelerated with smaller solder particles in solder paste.

Sign in / Sign up

Export Citation Format

Share Document