Measurement of Velocity-Dependent Adhesive Force Exerted on Magnetic Disk Using Micro-Probe of SPM

2003 ◽  
Vol 125 (4) ◽  
pp. 842-849 ◽  
Author(s):  
Yasunaga Mitsuya ◽  
Yasuji Ohshima
Keyword(s):  
Transient Response ◽  
High Speed ◽  
Fringe Pattern ◽  
Ccd Camera ◽  
Target Surface ◽  
Laser Interferometry ◽  
Adhesive Force ◽  
Magnetic Disk ◽  
Novel Method ◽  
Separation Force

A novel method for measuring the velocity-dependent adhesive force exerted on a magnetic disk has been developed using the micro-probe of a scanning probe microscope (SPM). The deformation of a cantilever having a diamond tip was measured based on the Michelson laser interferometry, wherein an interference fringe pattern was formed over the cantilever. The fringe images were captured by an ultra-high speed CCD camera, and then the deformation of the cantilever was accurately captured through image processing for extracting ridgelines from the fringe pattern. The high-speed camera enabled observation of the fringe image variation while the tip was being separated from a target surface, and identification of the transient response of the cantilever arising after separation by using the regression analysis. Then, the separation instant and the separation force were identified as the values of the initial condition of the transient response. Finally, this novel method was applied to the measurement of the separation force exerted on a magnetic disk coated with a molecularly thin lubricant film. As a result, the separation force was found to be approximately proportional to the square root of the retractive velocity.

Three-Dimensional Measurement of Head Flying Height and Attitude Using Image Processing of Fringe Patterns Formed by Michelson Laser Interferometry

1996 ◽  
Vol 118 (3) ◽  
pp. 564-570 ◽  
Author(s):  
Yasunaga Mitsuya ◽  
Akihito Mitsui ◽  
Yasuyuki Kawabe ◽  
Lars Lunde
Keyword(s):  
Image Processing ◽  
High Speed ◽  
Contact Region ◽  
Three Dimensional ◽  
Ccd Camera ◽  
Laser Interferometry ◽  
Disk Surface ◽  
Flying Height ◽  
Back Surface ◽  
Fringe Patterns

In-situ measurement of head flying height and attitude using image processing of fringe patterns formed by Michelson interferometry is studied. A wide laser beam is applied to illuminate the slider back surface and disk surface simultaneously to create interferometric fringe patterns. Employing the relationships arising between the two fringe patterns, the calculation procedure is formulated to yield the slider’s parallel, pitch and roll displacements. Experimental fringe patterns are captured in a single visual field by a high-speed CCD camera. Image processing for a higher signal-to-noise ratio, such as smoothing, filtering, amplification and ridge line extraction is then applied to the image data. Additionally, average processing with respect to multiple fringe lines to produce higher accuracy is successfully applied. Measured values of flying height and pitch and roll displacements are confirmed to be in good accordance with the calculation results, demonstrating excellent applicability of the present method down to the near-contact region.

High-speed brightfield 3-D imaging and 3-D image analysis of thick and overlapped cell clusters in cytological preparations

1994 ◽  
Vol 52 ◽  
pp. 218-219
Author(s):  
Robert W. Mackin
Keyword(s):  
Image Analysis ◽  
High Speed ◽  
Three Dimensional ◽  
Image Data ◽  
Ccd Camera ◽  
Objective Lens ◽  
Array Processor ◽  
Vaginal Smears ◽  
Low Contrast ◽  
Computer Controlled

This paper presents two advances towards the automated three-dimensional (3-D) analysis of thick and heavily-overlapped regions in cytological preparations such as cervical/vaginal smears. First, a high speed 3-D brightfield microscope has been developed, allowing the acquisition of image data at speeds approaching 30 optical slices per second. Second, algorithms have been developed to detect and segment nuclei in spite of the extremely high image variability and low contrast typical of such regions. The analysis of such regions is inherently a 3-D problem that cannot be solved reliably with conventional 2-D imaging and image analysis methods.High-Speed 3-D imaging of the specimen is accomplished by moving the specimen axially relative to the objective lens of a standard microscope (Zeiss) at a speed of 30 steps per second, where the stepsize is adjustable from 0.2 - 5μm. The specimen is mounted on a computer-controlled, piezoelectric microstage (Burleigh PZS-100, 68/μm displacement). At each step, an optical slice is acquired using a CCD camera (SONY XC-11/71 IP, Dalsa CA-D1-0256, and CA-D2-0512 have been used) connected to a 4-node array processor system based on the Intel i860 chip.

Five-Dimensional Microscopy using Widefield-Deconvolution: Practical Considerations and Biological Applications

1996 ◽  
Vol 54 ◽  
pp. 268-269
Author(s):  
W.F. Marshall ◽  
K. Oegema ◽  
J. Nunnari ◽  
A.F. Straight ◽  
D.A. Agard ◽  
...  
Keyword(s):  
Confocal Microscopy ◽  
High Speed ◽  
Laser Scanning ◽  
Ccd Camera ◽  
Image Plane ◽  
Time Lapse ◽  
Laser Scanning Confocal Microscopy ◽  
Three Dimensions ◽  
Excitation Light ◽  
Cooled Ccd

The ability to image cells in three dimensions has brought about a revolution in biological microscopy, enabling many questions to be asked which would be inaccessible without this capability. There are currently two major methods of three dimensional microscopy: laser-scanning confocal microscopy and widefield-deconvolution microscopy. The method of widefield-deconvolution uses a cooled CCD to acquire images from a standard widefield microscope, and then computationally removes out of focus blur. Using such a scheme, it is easy to acquire time-lapse 3D images of living cells without killing them, and to do so for multiple wavelengths (using computer-controlled filter wheels). Thus, it is now not only feasible, but routine, to perform five dimensional microscopy (three spatial dimensions, plus time, plus wavelength).Widefield-deconvolution has several advantages over confocal microscopy. The two main advantages are high speed of acquisition (because there is no scanning, a single optical section is acquired at a time by using a cooled CCD camera) and the use of low excitation light levels Excitation intensity can be much lower than in a confocal microscope for three reasons: 1) longer exposures can be taken since the entire 512x512 image plane is acquired in parallel, so that dwell time is not an issue, 2) the higher quantum efficiently of a CCD detect over those typically used in confocal microscopy (although this is expected to change due to advances in confocal detector technology), and 3) because no pinhole is used to reject light, a much larger fraction of the emitted light is collected. Thus we can typically acquire images with thousands of photons per pixel using a mercury lamp, instead of a laser, for illumination. The use of low excitation light is critical for living samples, and also reduces bleaching. The high speed of widefield microscopy is also essential for time-lapse 3D microscopy, since one must acquire images quickly enough to resolve interesting events.

scholarly journals High-Speed Dynamic Projection Mapping onto Human Arm with Realistic Skin Deformation

2021 ◽  
Vol 11 (9) ◽  
pp. 3753
Author(s):  
Hao-Lun Peng ◽  
Yoshihiro Watanabe
Keyword(s):  
User Interfaces ◽  
High Speed ◽  
Target Surface ◽  
Human Vision ◽  
Surface Model ◽  
Projection Mapping ◽  
Skin Deformation ◽  
Human Arm ◽  
Conventional Methods ◽  
Joint Tracking

Dynamic projection mapping for a moving object according to its position and shape is fundamental for augmented reality to resemble changes on a target surface. For instance, augmenting the human arm surface via dynamic projection mapping can enhance applications in fashion, user interfaces, prototyping, education, medical assistance, and other fields. For such applications, however, conventional methods neglect skin deformation and have a high latency between motion and projection, causing noticeable misalignment between the target arm surface and projected images. These problems degrade the user experience and limit the development of more applications. We propose a system for high-speed dynamic projection mapping onto a rapidly moving human arm with realistic skin deformation. With the developed system, the user does not perceive any misalignment between the arm surface and projected images. First, we combine a state-of-the-art parametric deformable surface model with efficient regression-based accuracy compensation to represent skin deformation. Through compensation, we modify the texture coordinates to achieve fast and accurate image generation for projection mapping based on joint tracking. Second, we develop a high-speed system that provides a latency between motion and projection below 10 ms, which is generally imperceptible by human vision. Compared with conventional methods, the proposed system provides more realistic experiences and increases the applicability of dynamic projection mapping.

scholarly journals Additively Manufactured Parts Made of a Polymer Material Used for the Experimental Verification of a Component of a High-Speed Machine with an Optimised Geometry—Preliminary Research

Polymers ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 137
Author(s):  
Artur Andrearczyk ◽  
Bartlomiej Konieczny ◽  
Jerzy Sokołowski
Keyword(s):  
Polymer Material ◽  
High Speed ◽  
Numerical Models ◽  
Flow Analysis ◽  
Experimental Tests ◽  
Strength Analysis ◽  
Compressor Wheel ◽  
Operational Characteristics ◽  
3D Printed ◽  
Novel Method

This paper describes a novel method for the experimental validation of numerically optimised turbomachinery components. In the field of additive manufacturing, numerical models still need to be improved, especially with the experimental data. The paper presents the operational characteristics of a compressor wheel, measured during experimental research. The validation process included conducting a computational flow analysis and experimental tests of two compressor wheels: The aluminium wheel and the 3D printed wheel (made of a polymer material). The chosen manufacturing technology and the results obtained made it possible to determine the speed range in which the operation of the tested machine is stable. In addition, dynamic destructive tests were performed on the polymer disc and their results were compared with the results of the strength analysis. The tests were carried out at high rotational speeds (up to 120,000 rpm). The results of the research described above have proven the utility of this technology in the research and development of high-speed turbomachines operating at speeds up to 90,000 rpm. The research results obtained show that the technology used is suitable for multi-variant optimization of the tested machine part. This work has also contributed to the further development of numerical models.

Transient Vibration of High-Speed, Lightweight Rotors Due to Sudden Imbalance

1983 ◽  
Vol 105 (3) ◽  
pp. 480-486 ◽  
Author(s):  
M. Sakata ◽  
T. Aiba ◽  
H. Ohnabe
Keyword(s):  
Transient Response ◽  
High Speed ◽  
Rotor System ◽  
Response Analysis ◽  
Transient Vibration ◽  
Flexible Shaft ◽  
Shaft System ◽  
Transient Response Analysis ◽  
Flexible Disk ◽  
Blade Loss

In the field of rotor dynamics, increased attention is being given to the transient response analysis of the rotor, since the effects of impact loading and vibrations of the rotor arising from blade loss can be studied by a time transient solution of the rotor system. As recent trends in rotating machinery have been directed towards lightweight, high-speed flexible rotors, the effect of flexibility on transient response analysis is becoming of increasing importance. In the present paper, a transient vibration analysis is carried out on a flexible-disk/flexible-shaft system or rigid-disk flexible-shaft system subjected to a sudden imbalance that is assumed to represent the effect of blade loss. To solve the basic equation governing a rotating flexible disk the Galerkin’s method is used, and the equation of motion of the rotor system is numerically solved by employing the Runge-Kutta-Gill’s method. Experiments were conducted on a model rotor having a blade loss simulator; the shaft vibrations were also measured. The validity of the anaytical results was demonstrated by comparison with the experimental results.

Application of Arithmetic Operations Method in Single Pair-Pole Magnetic Encoder

2011 ◽  
Vol 128-129 ◽  
pp. 85-91
Author(s):  
Yi Fan Zeng ◽  
Rui Li
Keyword(s):  
High Speed ◽  
Angle Measurement ◽  
Single Pair ◽  
Nonlinear Correction ◽  
Arithmetic Operations ◽  
Rotational Angle ◽  
Voltage Signal ◽  
Fpga Chip ◽  
Novel Method ◽  
Hall Sensors

This paper proposes a novel method called arithmetic operations to analyze and process the generated voltage-signal from the single pair-pole magnetic encoder. Dual orthogonal voltage-signals are generated by two vertical hall sensors which are placed in the bottom of a columned magnet. When signals pass A/D converter, the quadrant determination, arithmetic operations and nonlinear correction in FPGA chip are performed before the values of rotational angle are displayed on the LED. This paper also designs and implements the single pair-pole magnetic encoder which has advantages such as high-speed, high-resolution and high-accuracy in the area of angle measurement.

Towards A Multi-FPGA Infrared Simulator

2007 ◽  
Vol 4 (4) ◽  
pp. 343-355 ◽  
Author(s):  
Vinay Sriram ◽  
David Kearney
Keyword(s):  
Homeland Security ◽  
Reconfigurable Computing ◽  
High Speed ◽  
High Performance ◽  
Large Scale ◽  
Computation Time ◽  
Ccd Camera ◽  
Hardware Acceleration ◽  
Limiting Factor ◽  
Scene Simulation

High speed infrared (IR) scene simulation is used extensively in defense and homeland security to test sensitivity of IR cameras and accuracy of IR threat detection and tracking algorithms used commonly in IR missile approach warning systems (MAWS). A typical MAWS requires an input scene rate of over 100 scenes/second. Infrared scene simulations typically take 32 minutes to simulate a single IR scene that accounts for effects of atmospheric turbulence, refraction, optical blurring and charge-coupled device (CCD) camera electronic noise on a Pentium 4 (2.8GHz) dual core processor [7]. Thus, in IR scene simulation, the processing power of modern computers is a limiting factor. In this paper we report our research to accelerate IR scene simulation using high performance reconfigurable computing. We constructed a multi Field Programmable Gate Array (FPGA) hardware acceleration platform and accelerated a key computationally intensive IR algorithm over the hardware acceleration platform. We were successful in reducing the computation time of IR scene simulation by over 36%. This research acts as a unique case study for accelerating large scale defense simulations using a high performance multi-FPGA reconfigurable computer.

A Two-Dimensional Surface Profile Imaging Technique Based on Heterodyne Interferometer

2005 ◽  
Vol 295-296 ◽  
pp. 477-482
Author(s):  
K.W. Wang ◽  
Z.J. Cai ◽  
Li Jiang Zeng
Keyword(s):  
High Speed ◽  
Imaging Technique ◽  
Surface Profile ◽  
Ccd Camera ◽  
Measurement Range ◽  
Interference Signal ◽  
Two Dimensional ◽  
Step Method ◽  
Heterodyne Interferometer ◽  
Dimensional Surface

A two-dimensional surface profile imaging technique based on heterodyne interferometer is proposed. A piezo translator vibrated grating is used to generate a heterodyne signal. A high speed CCD camera is used to extract the interference signal using a five step method. The uncertainty in the displacement measurement is approximately 0.035 µm within a measurement range of 1.7 µm, confirming the two dimensional heterodyne interferometer is valid for measuring the surface profile. The method is also available for low coherence heterodyne interferometer due to the optical frequency shifts caused by the vibration of grating independent on the wavelength.

Sign in / Sign up

Export Citation Format

Share Document