Flow in a Centrifugal Pump Impeller at Design and Off-Design Conditions—Part II: Large Eddy Simulations

2003 ◽  
Vol 125 (1) ◽  
pp. 73-83 ◽  
Author(s):  
Rikke K. Byskov ◽  
Christian B. Jacobsen ◽  
Nicholas Pedersen
Keyword(s):  
Flow Field ◽  
Centrifugal Pump ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Pump Impeller ◽  
Design Load ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Subgrid Scales ◽  
Centrifugal Pump Impeller

The flow field in a shrouded six-bladed centrifugal pump impeller has been investigated using large eddy simulation (LES). The effect of the subgrid scales has been modeled through a localized dynamic Smagorinsky model implemented in the commercial CFD code FINE/Turbo. A detailed analysis of the results of LES at design load, Q=Qd, and severe off-design conditions, at quarter-load Q=0.25Qd, is presented. At design load LES reveals a well-behaved flow field with no significant separation. At quarter-load significant differences between adjacent impeller passages are revealed. A steady nonrotating stall phenomenon is observed in the entrance of one passage and a relative eddy develops in the remaining part of the passage. The stall unblocks the adjacent passage which exhibits a flow dominated by rotational effects. Velocities predicted by LES and steady-state Reynolds averaged Navier-Stokes (RANS) simulations based on the Baldwin-Lomax and Chien k-ε turbulence models are compared with experimental data obtained from particle image velocimetry (PIV). The complex two-channel phenomena observed by LES is with satisfactory agreement confirmed by PIV. However, it is found that the two RANS models do not reproduce the stall phenomenon observed at quarterload and are incapable of detecting the differences between the two passages.

scholarly journals Large Eddy Simulation of Periodic Transient Pressure Fluctuation in a Centrifugal Pump Impeller at Low Flow Rate

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 311
Author(s):  
Renfei Kuang ◽  
Xiaoping Chen ◽  
Zhiming Zhang ◽  
Zuchao Zhu ◽  
Yu Li
Keyword(s):  
Large Eddy Simulation ◽  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Low Frequency ◽  
Pump Impeller ◽  
Eddy Simulation ◽  
Inlet Flow Rate ◽  
Large Eddy ◽  
Centrifugal Pump Impeller

This paper presents a large eddy simulation of a centrifugal pump impeller during a transient condition. The flow rate is sinusoidal and oscillates between 0.25Qd (Qd indicates design load) and 0.75Qd when the rotating speed is maintained. Research shows that in one period, the inlet flow rate will twice reach 0.5Qd, and among the impeller of one moment is a stall state, but the other is a non-stall state. In the process of flow development, the evolution of low-frequency pressure fluctuation shows an obviously sinusoidal form, whose frequency is insensitive to the monitoring position and equals to that of the flow rate. However, inside the impeller, the phase and amplitude in the stall passages lag behind more and are stronger than that in the non-stall passages. Meanwhile, the strongest region of the high-frequency pressure fluctuation appears in the stall passages at the transient rising stage. The second dominant frequency in stall passages is 2.5 times to that in non-stall passages. In addition, similar to the pressure fluctuation, the evolution of the low-frequency head shows a sinusoidal form, whose phase is lagging behind that by one-third of a period in the inlet flow rate.

Investigation of rotating stall characteristics in a centrifugal pump impeller at low flow rates

2017 ◽  
Vol 34 (6) ◽  
pp. 1989-2000 ◽  
Author(s):  
Peijian Zhou ◽  
Fujun Wang ◽  
Jiegang Mou
Keyword(s):  
Centrifugal Pump ◽  
Rotating Stall ◽  
Low Flow ◽  
Pump Impeller ◽  
Flow Rates ◽  
Content Type ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Stall Cells ◽  
Centrifugal Pump Impeller

Purpose Rotating stall is an unsteady flow phenomenon that causes instabilities and low efficiency in pumps. The purpose of this paper is to investigate the rotating stall characteristics and unsteady behavior of stall cells in a centrifugal pump impeller at low flow rates. Design/methodology/approach A developed large eddy simulation with dynamic mixed nonlinear model is performed to evaluate the unsteady flow in a centrifugal pump impeller. The rotating stall flow field through the centrifugal pump impeller is analyzed under three typical flow rates. Frequency spectrum analysis are carried out on the series of pressure fluctuation to get the rotating stall characteristics. The size and intensity of stall cells are also analyzed using time-averaged vorticity and static pressure. Findings The rotating stall cell first occurs in the suction side of the blade and exhibits an obvious life cycle including decay mergence, shedding, growing and development with a low frequency. With the decrease of flow rate, the amplitude of pressure fluctuations in the impeller tends to be larger, the propagated speed of stall cells and rotating stall frequency tends to be smaller, but the number of cells remains unchanged. The size of stall cells increases as the flow rate decreases, but intensity changes is very little. Originality/value The rotating stall characteristics in a centrifugal pump impeller under low flow rates are presented first using a developed large eddy simulation approach.

scholarly journals Comparative Study of Different Turbulence Models for Cavitational Flows around NACA0012 Hydrofoil

2021 ◽  
Vol 9 (7) ◽  
pp. 742
Author(s):  
Minsheng Zhao ◽  
Decheng Wan ◽  
Yangyang Gao
Keyword(s):  
Angle Of Attack ◽  
Large Angle ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Specific Information ◽  
Cloud Cavitation ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Shedding Frequency ◽  
Reynolds Average

The present work focuses on the comparison of the numerical simulation of sheet/cloud cavitation with the Reynolds Average Navier-Stokes and Large Eddy Simulation(RANS and LES) methods around NACA0012 hydrofoil in water flow. Three kinds of turbulence models—SST k-ω, modified SST k-ω, and Smagorinsky’s model—were used in this paper. The unstable sheet cavity and periodic shedding of the sheet/cloud cavitation were predicted, and the simulation results, namelycavitation shape, shedding frequency, and the lift and the drag coefficients of those three turbulence models, were analyzed and compared with each other. The numerical results above were basically in accordance with experimental ones. It was found that the modified SST k-ω and Smagorinsky turbulence models performed better in the aspects of cavitation shape, shedding frequency, and capturing the unsteady cavitation vortex cluster in the developing and shedding period of the cavitation at the cavitation number σ = 0.8. At a small angle of attack, the modified SST k-ω model was more accurate and practical than the other two models. However, at a large angle of attack, the Smagorinsky model of the LES method was able to give specific information in the cavitation flow field, which RANS method could not give. Further study showed that the vortex structure of the wing is the main cause of cavitation shedding.

scholarly journals Investigation of the velocity field downstream of a benchmark vent using numerical simulation and hot-wire anemometry

2019 ◽  
Vol 213 ◽  
pp. 02076
Author(s):  
Jan Sip ◽  
Frantisek Lizal ◽  
Jakub Elcner ◽  
Jan Pokorny ◽  
Miroslav Jicha
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Velocity Field ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Turbulence Models ◽  
Hot Wire ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Precise Prediction

The velocity field in the area behind the automotive vent was measured by hot-wire anenemometry in detail and intensity of turbulence was calculated. Numerical simulation of the same flow field was performed using Computational fluid dynamics in commecial software STAR-CCM+. Several turbulence models were tested and compared with Large Eddy Simulation. The influence of turbulence model on the results of air flow from the vent was investigated. The comparison of simulations and experimental results showed that most precise prediction of flow field was provided by Spalart-Allmaras model. Large eddy simulation did not provide results in quality that would compensate for the increased computing cost.

scholarly journals Investigation of flow separation in a centrifugal pump impeller based on improved delayed detached eddy simulation method

2019 ◽  
Vol 11 (12) ◽  
pp. 168781401989783
Author(s):  
Yun Ren ◽  
Zuchao Zhu ◽  
Denghao Wu ◽  
Xiaojun Li ◽  
Lanfang Jiang
Keyword(s):  
Large Eddy Simulation ◽  
Centrifugal Pump ◽  
Flow Separation ◽  
Hybrid Algorithm ◽  
Internal Flow ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes ◽  
Vorticity Flux

The mechanism of flow separation in the impeller of a centrifugal pump with a low specific speed was explored by experimental, numerical, and theoretical methods. A novel delayed Reynolds-averaged Navier–Stokes/large eddy simulation hybrid algorithm combined with a rotation and curvature correction method was developed to calculate the inner flow field of the original pump for the large friction loss in the centrifugal impeller, high adverse pressure gradient, and large blade curvature. Boundary vorticity flux theory was introduced for internal flow diagnosis, and the relative velocity vector near the surface of the blade and the distribution of the dimensionless pressure coefficient was analyzed. The validity of the numerical method was verified, and the location of the backflow area and its flow features were determined. Finally, based on flow diagnosis, the geometric parameters influencing the flow state of the impeller were specifically adjusted to obtain a new design impeller. The results showed that the distribution of the boundary vorticity flux peak values, the skin friction streamline, and near-wall relative velocities improved significantly after the design change. In addition, the flow separation was delayed, the force applied on the blade was improved, the head under the part-load condition was improved, and the hydraulic efficiency was improved over the global flow ranges. It was demonstrated that the delayed Reynolds-averaged Navier–Stokes/large eddy simulation hybrid algorithm was capable to capture the separation flow in a centrifugal pump, and the boundary vorticity flux theory was suitable for the internal flow diagnosis of centrifugal pump.

Numerical Study of the Wave Impact on a Square Column Using Large Eddy Simulation

2007 ◽  
Author(s):  
H. T. C. Pedro ◽  
K.-W. Leung ◽  
M. H. Kobayashi ◽  
H. R. Riggs
Keyword(s):  
Numerical Study ◽  
Turbulence Models ◽  
Simple Algorithm ◽  
Navier Stokes ◽  
Wave Impact ◽  
Eddy Simulation ◽  
Subgrid Model ◽  
Large Eddy ◽  
Volume Approximation ◽  
The Impact

This work concerns the numerical investigation of the impact of a wave on a square column. The wave is generated by a dam break in a wave tank. Two turbulence models were used: Large Eddy Simulations (LES) and Unsteady Reynolds Averaged Navier-Stokes (URANS). The numerical simulations were carried out using a finite volume approximation and the SIMPLE algorithm for the solution of the governing equations. Turbulence was modeled with the standard Smagorinsky-Lilly subgrid-model for the LES and the standard κ-ε model for the URANS. The results are validated against experimental data for the wave impact on a square column facing the flow. The results, especially for LES, show very good agreement between the predictions and experimental results. The overall accuracy of the LES, as expected, is superior to the URANS. However, if computational resources are limited, URANS can still provide satisfactory results for structural design.

scholarly journals Comparative Study on CFD Turbulence Models for the Flow Field in Air Cooled Radiator

Processes ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 1687
Author(s):  
Chao Yu ◽  
Xiangyao Xue ◽  
Kui Shi ◽  
Mingzhen Shao ◽  
Yang Liu
Keyword(s):  
Flow Field ◽  
Transient Flow ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Compartment Model ◽  
Navier Stokes ◽  
Engine Compartment ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Relevant Calculation

This paper compares the performances of three Computational Fluid Dynamics (CFD) turbulence models, Reynolds Average Navier-Stokes (RANS), Detached Eddy Simulation (DES), and Large Eddy Simulation (LES), for simulating the flow field of a wheel loader engine compartment. The distributions of pressure fields, velocity fields, and vortex structures in a hybrid-grided engine compartment model are analyzed. The result reveals that the LES and DES can capture the detachment and breakage of the trailing edge more abundantly and meticulously than RANS. Additionally, by comparing the relevant calculation time, the feasibility of the DES model is proved to simulate the three-dimensional unsteady flow of engine compartment efficiently and accurately. This paper aims to provide a guiding idea for simulating the transient flow field in the engine compartment, which could serve as a theoretical basis for optimizing and improving the layout of the components of the engine compartment.

On the Investigation of Flow around the Square Cylinder Based on Different LES Models

2012 ◽  
Vol 594-597 ◽  
pp. 2676-2679
Author(s):  
Zhe Liu
Keyword(s):  
Flow Characteristics ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Square Cylinder ◽  
Rans Model ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes ◽  
Les Model

Although the conventional Reynolds-averaged Navier–Stokes (RANS) model has been widely applied in the industrial and engineering field, it is worthwhile to study whether these models are suitable to investigate the flow filed varying with the time. With the development of turbulence models, the unsteady Reynolds-averaged Navier–Stokes (URANS) model, detached eddy simulation (DES) and large eddy simulation (LES) compensate the disadvantage of RANS model. This paper mainly presents the theory of standard LES model, LES dynamic model and wall-adapting local eddy-viscosity (WALE) LES model. And the square cylinder is selected as the research target to study the flow characteristics around it at Reynolds number 13,000. The influence of different LES models on the flow field around the square cylinder is compared.

Effect of URANS and Hybrid RANS-Large Eddy Simulation Turbulence Models on Unsteady Turbulent Flows Inside a Side Channel Pump

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Yefang Wang ◽  
Fan Zhang ◽  
Shouqi Yuan ◽  
Ke Chen ◽  
Xueyuan Wei ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Turbulence Models ◽  
Swirling Flows ◽  
Navier Stokes ◽  
Side Channel ◽  
Fluid Exchange ◽  
Eddy Simulation ◽  
Internal Fluid ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes

Abstract In this work, the unsteady Reynolds-averaged Navier–Stokes (URANS) and three hybrid Reynolds-averaged Navier–Stokes-large eddy simulation (RANS-LES) models are employed to resolve the vortical flows in a typical single-stage side channel pump, to evaluate the suitability of these advanced turbulence models in predicting the pump hydraulic performance and unstable swirling flows. By the comparison of the overall performance, it can be observed that the results obtained by scale-adapted simulation (SAS) are closer to test data than shear stress transport (SST), detached eddy simulation (DES) and filter-based model (FBM). Simultaneously, the distribution of axial velocity on the plane near the interface is used to describe the position and intensity of internal fluid exchange between impeller and side channel. It is obvious that the intensity of mass flow exchange is strong near the inner and outer edges. Then, the vortex core region illustrates that the vortex is easily produced near the interface due to internal fluid exchange. Finally, the evolutions of circumferential in-plane vortical structures are presented to further account for the process of fluid exchange and the main vortex flows. It reveals that the recirculation flow presents a strong instability during 6–7 blade pitches as the fluid enters into the impeller and the flow is stable in downstream 7–8 blade pitches. Besides, the flow turns to be unsteady near outlet affected by the sudden change of fluid direction. This work could provide some suggestions for the choice of appropriate turbulence model in simulating strong swirling flows.

Sign in / Sign up

Export Citation Format

Share Document