Time-Resolved Vane-Rotor Interaction in a High-Pressure Turbine Stage

2003 ◽  
Vol 125 (1) ◽  
pp. 1-13 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
C. K. Horwood
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Time Varying ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Trailing Edge ◽  
Time Resolved ◽  
Periodic Fluctuation ◽  
Interaction Mechanisms ◽  
Numerical Predictions

This paper describes the time-varying aerodynamic interaction mechanisms that have been observed within a transonic high-pressure turbine stage; these are inferred from the time-resolved behavior of the rotor exit flow field. It contains results both from an experimental program in a turbine test facility and from numerical predictions. Experimental data was acquired using a fast-response aerodynamic probe capable of measuring Mach number, whirl angle, pitch angle, total pressure, and static pressure. A 3-D time-unsteady viscous Navier-Stokes solver was used for the numerical predictions. The unsteady rotor exit flowfield is formed from a combination of four flow phenomena: the rotor wake, the rotor trailing edge recompression shock, the tip-leakage flow, and the hub secondary flow. This paper describes the time-resolved behavior of each phenomenon and discusses the interaction mechanisms from which each originates. Two significant vane periodic changes (equivalent to a time-varying flow in the frame of reference of the rotor) in the rotor exit flowfield are identified. The first is a severe vane periodic fluctuation in flow conditions close to the hub wall and the second is a smaller vane periodic fluctuation occurring at equal strength over the entire blade span. These two regions of periodically varying flow are shown to be caused by two groups of interaction mechanisms. The first is thought to be caused by the interaction between the wake and secondary flow of the vane with the downstream rotor; and the second is thought to be caused by a combination of the interaction of the vane trailing edge recompression shock with the rotor, and the interaction between the vane and rotor potential fields.

The Development of Turbine Exit Flow in a Swan-Necked Inter-Stage Diffuser

2003 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
N. W. Harvey
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Leakage Flow ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Inlet Flow ◽  
Time Resolved ◽  
Tip Leakage ◽  
Numerical Predictions

This paper describes both the migration and dissipation of flow phenomena downstream of a transonic high-pressure turbine stage. The geometry of the HP stage exit duct considered is a swan-necked diffuser similar to those likely to be used in future engine designs. The paper contains results both from an experimental programme in a turbine test facility and from numerical predictions. Experimental data was acquired using three fast-response aerodynamic probes capable of measuring Mach number, whirl angle, pitch angle, total pressure and static pressure. The probes were used to make time-resolved area traverses at two axial locations downstream of the rotor trailing edge. A 3D time-unsteady viscous Navier-Stokes solver was used for the numerical predictions. The unsteady exit flow from a turbine stage is formed from rotor-dependent phenomena (such as the rotor wake, the rotor trailing edge recompression shock, the tip-leakage flow and the hub secondary flow) and vane-rotor interaction dependant phenomena. This paper describes the time-resolved behaviour and three-dimensional migration paths of both of these phenomena as they convect downstream. It is shown that the inlet flow to a downstream vane is dominated by two corotating vortices, the first caused by the rotor tip-leakage flow and the second by the rotor hub secondary flow. At the inlet plane of the downstream vane the wake is extremely weak and the radial pressure gradient is shown to have caused the majority of the high loss wake fluid to be located between the mid-height of the passage and the casing wall. The structure of the flow indicates that between a high pressure stage and a downstream vane simple two-dimensional blade row interaction does not occur. The results presented in this paper indicate that the presence of an upstream stage is likely to significantly alter the structure of the secondary flow within a downstream vane. The paper also shows that vane-rotor interaction within the upstream stage causes a 10° circumferential variation in the inlet flow angle of the 2nd stage vane.

Comparison of Steady and Unsteady Coupled Heat-Transfer Simulations of a High-Pressure Turbine Blade

2015 ◽  
Author(s):  
Markus Schmidt ◽  
Christoph Starke
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Steady State ◽  
Flow Field ◽  
Film Cooling ◽  
Strong Increase ◽  
Pressure Side ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Time Resolved

This article presents results for the coupled simulation of a high-pressure turbine stage in consideration of unsteady hot gas flows. A semi-unsteady coupling process was developed to solve the conjugate heat transfer problem for turbine components of gas turbines. Time-resolved CFD simulations are coupled to a finite element solver for the steady state heat conduction inside of the blade material. A simplified turbine stage geometry is investigated in this paper to describe the influence of the unsteady flow field onto the time-averaged heat transfer. Comparisons of the time-resolved results to steady state results indicate the importance of a coupled simulation and the consideration of the time-dependent flow-field. Different film-cooling configurations for the turbine NGV are considered, resulting in different temperature and pressure deficits in the vane wake. Their contribution to non-linear effects causing the time-averaged heat load to differ from a steady result is discussed to further highlight the necessity of unsteady design methods for future turbine developments. A strong increase in the pressure side heat transfer coefficients for unsteady simulations is observed in all results. For higher film-cooling mass flows in the upstream row, the preferential migration of hot fluid towards the pressure side of a turbine blade is amplified as well, which leads to a strong increase in material temperature at the pressure side and also in the blade tip region.

Fourier Decomposed Turbulence Measurements Downstream of a High-Pressure Turbine Stage

2008 ◽  
Author(s):  
Lars-Uno Axelsson ◽  
William K. George ◽  
T. Gunnar Johansson
Keyword(s):  
High Pressure ◽  
Periodic Component ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Time Resolved ◽  
Velocity Fluctuations ◽  
Axial Turbine ◽  
Blade Passage ◽  
Turbulence Measurements ◽  
Time Resolved Measurements

This forum paper discusses phase-resolved turbulence measurements of the flow downstream of an axial turbine, and especially how phase-resolved measurements compare to time-resolved measurements. The time-resolved spectra produced higher velocity fluctuations than the corresponding phase-resolved spectra even when the periodic component was filtered out from the time-resolved measurements. The phase-resolved spectrum effectively removes all the peaks in the spectrum except for the ones associated with the blade-passage frequency.

Wake–Wake Interaction and Its Potential for Clocking in a Transonic High-Pressure Turbine

2001 ◽  
Vol 124 (1) ◽  
pp. 69-76 ◽  
Author(s):  
Frank Hummel
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Flow Direction ◽  
Numerical Procedure ◽  
Flow Simulation ◽  
Suction Side ◽  
Frame Of Reference ◽  
High Pressure Turbine ◽  
Trailing Edge ◽  
Time Resolved

Two-dimensional unsteady Navier–Stokes calculations of a transonic single-stage high-pressure turbine were carried out with emphasis on the flow field behind the rotor. Detailed validation of the numerical procedure with experimental data showed excellent agreement in both time-averaged and time-resolved flow quantities. The numerical timestep as well as the grid resolution allowed the prediction of the Ka´rma´n vortex streets of both stator and rotor. Therefore, the influence of the vorticity shed from the stator on the vortex street of the rotor is detectable. It was found that certain vortices in the rotor wake are enhanced while others are diminished by passing stator wake segments. A schematic of this process is presented. In the relative frame of reference, the rotor is operating in a transonic flow field with shocks at the suction side trailing edge. These shocks interact with both rotor and stator wakes. It was found that a shock modulation occurs in time and space due to the stator wake passing. In the absolute frame of reference behind the rotor, a 50-percent variation in shock strength is observed according to the circumferential or clocking position. Furthermore, a substantial weakening of the rotor suction side trailing edge shock in flow direction is detected in an unsteady flow simulation when compared to a steady-state calculation, which is caused by convection of upstream stator wake segments. The physics of the aforementioned unsteady phenomena as well as their influence on design are discussed.

Computational and Experimental Study of the Unsteady Convection of Entropy Waves Within a High Pressure Turbine Stage

2020 ◽  
Author(s):  
Lorenzo Pinelli ◽  
Michele Marconcini ◽  
Roberto Pacciani ◽  
Paolo Gaetani ◽  
Giacomo Persico
Keyword(s):  
High Pressure ◽  
High Speed ◽  
Low Frequency ◽  
Frequency Content ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Cfd Simulations ◽  
Time Resolved ◽  
Azimuthal Position ◽  
Cfd Method

Abstract This paper describes the transport and the interaction of pulsating entropy waves generated by combustor burners within a high pressure turbine stage for aeronautical application. Experiments and Computational Fluid Dynamics (CFD) simulations were carried out in the context of the European Research Project RECORD. Experimental campaigns considering burner-representative temperature fluctuations (in terms of spot shape, fluctuation frequency and total temperature variation percentage) injected upstream of an un-cooled high-pressure gas turbine stage have been performed in the high-speed closed-loop test-rig of the Fluid Machine Laboratory (LFM) of Politecnico di Milano (Italy). The pulsating entropy waves are injected at the stage inlet in streamwise direction at four different azimuthal positions featuring a 7% over-temperature with respect to the main flow with a frequency of 90 Hz. Detailed time-resolved temperature measurements (in the range of 0–200 Hz) upstream and downstream of the stage, as well as in the stator–rotor axial gap were performed. Time-accurate CFD simulations with and without entropy fluctuations imposed at the stage inlet were performed with the TRAF code, developed by the University of Florence. A numerical post-processing procedure, based on the DFT (Discrete Fourier Transform) of the conservative variables has been implemented to extract the low frequency content connected to the entropy fluctuations. Measurements highlighted a significant attenuation of the entropy wave spot throughout their transport within the stator channel and their interaction with the rotor blade rows, highly depending on their injection azimuthal position. Simulations show an overall good agreement with the experiments on the measurement traverses, especially at the stage outlet. By exploiting the combination of experiments and simulations, the aerodynamic and thermal implications of the temperature fluctuation injected upstream of the stage were properly assessed, thus allowing suggest useful information to the designer. The comparison with the experiments confirms the accuracy of the CFD method to solve the periodic, but characterized by a low frequency content event, associated with the entropy wave fluctuation.

Numerical study on the biomimetic trailing edge in the environment of a high-pressure turbine stage

2021 ◽  
pp. 106770
Author(s):  
Yuxi Luo ◽  
Fengbo Wen ◽  
Shuai Wang ◽  
Rui Hou ◽  
Songtao Wang ◽  
...  
Keyword(s):  
High Pressure ◽  
Numerical Study ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Trailing Edge

Influence of Hot Streak Temperature Ratio on Low Pressure Stage of a Vaneless Counter-Rotating Turbine

2007 ◽  
Author(s):  
Qingjun Zhao ◽  
Fei Tang ◽  
Huishe Wang ◽  
Jianyi Du ◽  
Xiaolu Zhao ◽  
...  
Keyword(s):  
Shock Wave ◽  
High Pressure ◽  
Secondary Flow ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Temperature Ratio ◽  
High Pressure Turbine ◽  
Pressure Stage ◽  
Low Pressure Turbine ◽  
Hot Streak

In order to explore the influence of hot streak temperature ratio on low pressure stage of a Vaneless Counter-Rotating Turbine, three-dimensional multiblade row unsteady Navier-Stokes simulations have been performed. The predicted results show that hot streaks are not mixed out by the time they reach the exit of the high pressure turbine rotor. The separation of colder and hotter fluids is observed at the inlet of the low pressure turbine rotor. After making interactions with the inner-extending shock wave and outer-extending shock wave in the high pressure turbine rotor, the hotter fluid migrates towards the pressure surface of the low pressure turbine rotor, and the most of colder fluid migrates to the suction surface of the low pressure turbine rotor. The migrating characteristics of the hot streaks are predominated by the secondary flow in the low pressure turbine rotor. The effect of buoyancy on the hotter fluid is very weak in the low pressure turbine rotor. The results also indicate that the secondary flow intensifies in the low pressure turbine rotor when the hot streak temperature ratio is increased. The effects of the hot streak temperature ratio on the relative Mach number and the relative flow angle at the inlet of the low pressure turbine rotor are very remarkable. The isentropic efficiency of the Vaneless Counter-Rotating Turbine decreases as the hot streak temperature ratio is increased.

Investigation of Trailing Edge Cooling Concepts in a High Pressure Turbine Cascade—Aerodynamic Experiments and Loss Analysis

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Hans-Ju¨rgen Rehder
Keyword(s):  
Boundary Layer ◽  
High Pressure ◽  
Coolant Flow ◽  
Coolant Fluid ◽  
Pressure Side ◽  
Turbine Cascade ◽  
High Pressure Turbine ◽  
Trailing Edge ◽  
Number Range ◽  
Mixing Losses

As part of a European research project, the aerodynamic and thermodynamic performance of a high pressure turbine cascade with different trailing edge cooling configurations was investigated in the wind tunnel for linear cascades at DLR in Go¨ttingen. A transonic rotor profile with a relative thick trailing edge was chosen for the experiments. Three trailing edge cooling configurations were applied, first central trailing edge ejection, second a trailing edge shape with a pressure side cut-back and slot equipped with a diffuser rib array, and third pressure side film cooling through a row of cylindrical holes. For comparison, aerodynamic investigations on a reference cascade with solid blades (no cooling holes or slots) were performed. The experiments covered the subsonic, transonic and supersonic exit Mach number range of the cascade while varying cooling mass flow ratios up to 2 %. This paper analyzes the effect of coolant ejection on the airfoil losses. Emphasis was given on separating the different loss contributions due to shocks, pressure, and suction side boundary layer, trailing edge, and mixing of the coolant flow. Employed measurement techniques are schlieren visualization, blade surface pressure measurements, and traverses by pneumatic probes in the cascade exit flow field and around the trailing edge. The results show that central trailing edge ejection significantly reduces the mixing losses and therefore decreases the overall loss. Higher loss levels are obtained when applying the configurations with pressure side blowing. In particular, the cut-back geometry reveals strong mixing losses due to the low momentum coolant fluid, which is decelerated by the diffuser rib array inside the slot. The influence of coolant flow rate on the trailing edge loss is tremendous, too. Shock and boundary layer losses are major contributions to the overall loss but are less affected by the coolant. Finally a parameter variation changing the temperature ratio of coolant to main flow was performed, resulting in increasing losses with decreasing coolant temperature.

Design Optimization of Profiled Endwall With Consideration of Cooling and Rim Seal Flow Effects

2016 ◽  
Author(s):  
Huimin Tang ◽  
Shuaiqiang Liu ◽  
Hualing Luo
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Secondary Flow ◽  
Three Dimensional ◽  
Great Influence ◽  
Optimization Procedure ◽  
Secondary Flows ◽  
High Pressure Turbine ◽  
Operation Condition ◽  
Turbine Performance

Profiled endwall is an effective method to improve aerodynamic performance of turbine. This approach has been widely studied in the past decade on many engines. When automatic design optimisation is considered, most of the researches are usually based on the assumption of a simplified simulation model without considering cooling and rim seal flows. However, many researchers find out that some of the benefits achieved by optimization procedure are lost when applying the high-fidelity geometry configuration. Previously, an optimization procedure has been implemented by integrating the in-house geometry manipulator, a commercial three-dimensional CFD flow solver and the optimization driver, IsightTM. This optimization procedure has been executed [12] to design profiled endwalls for a turbine cascade and a one-and-half stage axial turbine. Improvements of the turbine performance have been achieved. As the profiled endwall is applied to a high pressure turbine, the problems of cooling and rim seal flows should be addressed. In this work, the effects of rim seal flow and cooling on the flow field of two-stage high pressure turbine have been presented. Three optimization runs are performed to design the profiled endwall of Rotor-One with different optimization model to consider the effects of rim flow and cooling separately. It is found that the rim seal flow has a significant impact on the flow field. The cooling is able to change the operation condition greatly, but barely affects the secondary flow in the turbine. The influences of the profiled endwalls on the flow field in turbine and cavities have been analyzed in detail. A significant reduction of secondary flows and corresponding increase of performance are achieved when taking account of the rim flows into the optimization. The traditional optimization mechanism of profiled endwall is to reduce the cross passage gradient, which has great influence on the strength of the secondary flow. However, with considering the rim seal flows, the profiled endwall improves the turbine performance mainly by controlling the path of rim seal flow. Then the optimization procedure with consideration of rim seal flow has also been applied to the design of the profiled endwall for Stator Two.

APPLICATION OF SCALE ADAPTIVE SIMULATION MODEL TO STUDYING COOLING CHARACTERISTICS OF A HIGH PRESSURE TURBINE BLADE CUTBACK TRAILING EDGE WITH DIFFERENT COOLING CONFIGURATIONS

2021 ◽  
pp. 1-53
Author(s):  
Yuefeng Li ◽  
Huazhao Xu ◽  
Jianhua Wang ◽  
Wei Song ◽  
Ming Wang ◽  
...  
Keyword(s):  
High Pressure ◽  
High Pressure Turbine ◽  
Baseline Model ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Adaptive Simulation ◽  
Rear Part ◽  
Pin Fins ◽  
A Minor ◽  
Better Than

Abstract This paper adopted Scale Adaptive Simulation (SAS) to investigate fluid flow and cooling characteristics in detail downstream of a high pressure turbine (HPT) blade trailing edge (TE) cutback region. The effects of typical TE configurations on cutback cooling performance are investigated including three types of internal turbulators, the cutback with/without land extensions and three kinds of ejection lip profiles. The elliptic pin fins with streamwise orientation significantly improve ηaw at the rear part of the cutback surface over the baseline model with cylindrical pin fins and slightly increase Cd. However, the elliptic pin fins with spanwise orientation drastically reduce the ηaw and Cd. Downstream of the cutback, the coherent structures are strongly disturbed and become chaotic compared to the TE with cylindrical and streamwise oriented elliptic pin fins. The application of land extensions only causes an evident change to the coherent structure immediate downstream of the lip, and slightly improves ηaw and reduces Cd over the baseline model on the rear part of the cutback surface. Rounded lip shapes B and C also show an obvious increase in ηaw on the rear part of the cutback surface but only a minor increase in Cd compared to the straight lip shape A. The rounded lip helps the coolant diffuse into the TE cutback and reduce the intensity of mixing. Due to larger rounding radius of shape B, the cooling effectiveness predicted by shape B is slightly better than shape C.

Sign in / Sign up

Export Citation Format

Share Document