An Experimental Analysis of Misalignment Effects on Hydrodynamic Plain Journal Bearing Performances

2001 ◽  
Vol 124 (2) ◽  
pp. 313-319 ◽  
Author(s):  
J. Bouyer ◽  
M. Fillon
Keyword(s):  
Film Thickness ◽  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Operating Conditions ◽  
Temperature Fields ◽  
Maximum Pressure ◽  
Minimum Film Thickness ◽  
Oil Flow ◽  
Hydrodynamic Effects

The present study deals with the experimental determination of the performance of a 100 mm diameter plain journal bearing submitted to a misalignment torque. Hydrodynamic pressure and temperature fields in the mid-plane of the bearing, temperatures in two axial directions, oil flow rate, and minimum film thickness, were all measured for various operating conditions and misalignment torques. Tests were carried out for rotational speeds ranging from 1500 to 4000 rpm with a maximum static load of 9000 N and a misalignment torque varying from 0 to 70 N.m. The bearing performances were greatly affected by the misalignment. The maximum pressure in the mid-plane decreased by 20 percent for the largest misalignment torque while the minimum film thickness was reduced by 80 percent. The misalignment caused more significant changes in bearing performance when the rotational speed or load was low. The hydrodynamic effects were then relatively small and the bearing offered less resistance to the misalignment.

Improvement of the THD Performance of a Misaligned Plain Journal Bearing

2003 ◽  
Vol 125 (2) ◽  
pp. 334-342 ◽  
Author(s):  
J. Bouyer ◽  
M. Fillon
Keyword(s):  
Film Thickness ◽  
Flow Rate ◽  
Journal Bearing ◽  
Numerical Study ◽  
Axial Flow ◽  
Hydrodynamic Pressure ◽  
Operating Conditions ◽  
Local Defect ◽  
Minimum Film Thickness ◽  
Global Defect

This numerical study deals with the improvement of the thermohydrodynamic performance of a 100 mm plain journal bearing submitted to a constant misalignment torque under steady-state conditions. The performance of the misaligned journal bearing is improved by adding either a local or a global defect to the bearing geometry. The influence on bearing performance of the local defect, situated in the zone of minimum film thickness, is analyzed by using various widths and lengths of defect. A global defect, which is conical in shape and is located at one end of the bearing, is also studied under varying direction and magnitude of misalignment torque. Our main focus was on hydrodynamic pressure, temperature distributions at the film/bush interface, oil flow rate, power losses and film thickness. The defects significantly improved the performance of the bearing. The minimum film thickness increased by more than 60 percent and the temperature decreased, whilst the axial flow rate was barely affected. Thus, the defects can be an effective solution for misaligned bearings when they are submitted to extreme operating conditions.

Dynamic Analysis of Tilting-Pad Journal Bearing—Influence of Pad Deformations

1994 ◽  
Vol 116 (3) ◽  
pp. 621-627 ◽  
Author(s):  
H. Desbordes ◽  
M. Fillon ◽  
C. Chan Hew Wai ◽  
J. Frene
Keyword(s):  
Film Thickness ◽  
Pressure Field ◽  
Journal Bearing ◽  
Maximum Pressure ◽  
Tilting Pad ◽  
Minimum Film Thickness ◽  
Dimensional Finite Element ◽  
The One ◽  
Tilting Pad Journal Bearing ◽  
Tilting Pad Journal Bearings

A theoretical nonlinear analysis of tilting-pad journal bearings is presented for small and large unbalance loads under isothermal conditions. The radial displacements of internal pad surface due to pressure field are determined by a two-dimensional finite element method in order to define the actual film thickness. The influence of pad deformations on the journal orbit, on the minimum film thickness and on the maximum pressure is studied. The effects of pad displacements are to decrease the minimum film thickness and to increase the maximum pressure. The orbit amplitude is also increased by 20 percent for the large unbalance load compared to the one obtained for rigid pad.

scholarly journals A Quantitative Determination of Minimum Film Thickness in Elastohydrodynamic Circular Contacts

2021 ◽  
Author(s):  
Wassim Habchi ◽  
Philippe Vergne
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Numerical Model ◽  
Film Thickness ◽  
Quantitative Determination ◽  
Excellent Agreement ◽  
Operating Conditions ◽  
Pure Rolling ◽  
Minimum Film Thickness

Abstract The current work presents a quantitative approach for the prediction of minimum film thickness in elastohydrodynamic lubricated (EHL) circular contacts. In contrast to central film thickness, minimum film thickness can be hard to accurately measure, and it is usually poorly estimated by classical analytical film thickness formulae. For this, an advanced finite-element-based numerical model is used to quantify variations of the central-to-minimum film thickness ratio with operating conditions, under isothermal Newtonian pure-rolling conditions. An ensuing analytical expression is then derived and compared to classical film thickness formulae and to more recent similar expressions. The comparisons confirmed the inability of the former to predict the minimum film thickness, and the limitations of the latter, which tend to overestimate the ratio of central-to-minimum film thickness. The proposed approach is validated against numerical results as well as experimental data from the literature, revealing an excellent agreement with both. This framework can be used to predict minimum film thickness in circular elastohydrodynamic contacts from knowledge of central film thickness, which can be either accurately measured or rather well estimated using classical film thickness formulae.

Influence of Scratches on the Performance of a Partial Journal Bearing

2008 ◽  
Author(s):  
Mihai B. Dobrica ◽  
Michel Fillon
Keyword(s):  
Film Thickness ◽  
Thermal Effects ◽  
Journal Bearing ◽  
Friction Torque ◽  
Maximum Pressure ◽  
Relative Depth ◽  
Performance Loss ◽  
Minimum Film Thickness ◽  
Overall Performance ◽  
Bearing Damage

In this paper, the influence of circumferential scratches on the thermohydrodynamic performance of a partial (lobe) journal bearing is studied. The bearing damage is characterized by four factors: the area of the scratched region, the density of the scratches within the affected area, the relative position of the scratched region and the relative depth of the wear defects. The bearing performance is characterized by minimum film thickness, average oil temperature, maximum pressure, friction torque etc., at imposed magnitude and direction of the load. A numerical hydrodynamic model with global thermal effects is used for studying the influence of the different wear related parameters on the bearing performance. The results permit to predict the overall performance loss due to the circumferential wear marks, for different wear profiles. The types of wear profiles that can lead to the bearing destruction (characterized by a critical minimum film thickness) are also investigated.

An analysis of the influence of oil supply conditions on the thermohydrodynamic performance of a single-groove journal bearing

2003 ◽  
Vol 217 (2) ◽  
pp. 133-144 ◽  
Author(s):  
L Costa ◽  
A. S. Miranda ◽  
M Fillon ◽  
J. C. P. Claro
Keyword(s):  
Film Thickness ◽  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Quantitative Information ◽  
Published Data ◽  
Oil Supply ◽  
Supply Pressure ◽  
Minimum Film Thickness ◽  
Theoretical Predictions ◽  
Loss Maximum

In this work a thermohydrodynamic analysis has been developed in order to investigate the influence of oil supply conditions on the performance of a journal bearing. The supply conditions considered were oil supply temperature, supply pressure, groove length and groove location. To carry out this study, the hydrodynamic pressure distribution inside the bearing has been determined using a mass-conserving cavitation model with realistic supply conditions. The energy equation and the heat conduction equation have been used for the determination of oil film and bush temperature distributions. The agreement observed between theoretical predictions and experimental published data is acceptable. Quantitative information shows that the oil supply conditions affect bearing performance parameters in different ways. Oil flowrate was markedly affected by all supply parameters studied. Power loss, maximum bush temperature and minimum film thickness were mainly dependent on oil supply temperature. The effect of supply pressure on minimum film thickness was dependent on groove location. An axial groove located at 90° to the load line gave rise to more favourable bearing performance characteristics.

Investigation of the Failure of Heavily Loaded Journal Bearings

1994 ◽  
Vol 208 (3) ◽  
pp. 167-171
Author(s):  
D Ashman
Keyword(s):  
Film Thickness ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Elastohydrodynamic Lubrication ◽  
Failure Criteria ◽  
Operating Conditions ◽  
Minimum Film Thickness ◽  
Hydrodynamic Solution ◽  
Metrological Study ◽  
Theoretical Minimum

This paper gives details of a combined theoretical and experimental investigation of a plain journal bearing under heavily loaded conditions together with a metrological study of the bearing geometry. It was found that under high loading conditions a simplified analytical expression relating the Sommerfeld number to the non-dimensional minimum film thickness, using a hydrodynamic solution of the isoviscous form of the Reynolds equation, could be developed. An alternative theoretical solution based on elastohydrodynamic lubrication was also considered. In addition, experimental work determined a variety of operating conditions that produced metal-to-metal contact. These operating conditions were then compared with the theoretical minimum film thickness calculations and bearing manufacturing data. This process was used to determine combined failure criteria based on operating conditions and machining capability.

scholarly journals Roughness Effect on Thermo-Elasto-Hydrodynamic Performance of a 170ᵒ -Arc Partial Journal Bearing

2021 ◽  
Vol 27 (1) ◽  
pp. 16-34
Author(s):  
Souad Jabbar Shamal ◽  
Luay Sadiq Al-Ansari ◽  
Ahmed Niameh Mehdy Alhusseny ◽  
Adel Gharib Nasser
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Iterative Solution ◽  
Operating Conditions ◽  
Hydrodynamic Performance ◽  
Temperature Deformation ◽  
Maximum Pressure ◽  
Static Structure ◽  
Scratch Depth ◽  
Wide Range

In the current analysis, the effects of circumferential scratches along the inner surface of a 170ᵒ -arc partial journal bearing has been numerically investigated. Their impact on the thermo-elasto-hydrodynamic performance characteristics, including maximum pressure, temperature, deformation, and stress, has been examined thoroughly. The ANSYS Fluent CFD commercial code was employed to tackle the iterative solution of flow and heat transfer patterns in the fluid film domain. They are then applied to the ANSYS Static Structure solver to compute the deformation and stress resulted in the solid bearing zone. A wide range of operating conditions has been considered, including the eccentricity ratio ( ) and scratch depth ( ). In contrast, the bearing length-diameter ratio (L/D) and the rotation speed (N) have been fixed at 0.77 and 1500 rpm, respectively. The thermo-hydrodynamic pressure, temperature, stress, and deformation have all been computed. It was found that the scratch depth has a direct effect on the thermo-hydrodynamic performance of the partial bearings. Meanwhile, the deep central scratches are important, especially at scratch depth equal to 0.224 mm.

Profile Design for Misaligned Journal Bearings Subjected to Transient Mixed Lubrication

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Thomas Gu ◽  
Q. Jane Wang ◽  
Shangwu Xiong ◽  
Zhong Liu ◽  
Arup Gangopadhyay ◽  
...  
Keyword(s):  
Film Thickness ◽  
Performance Metrics ◽  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Hydrodynamic Pressure ◽  
Industrial Applications ◽  
Mixed Lubrication ◽  
Asperity Contact ◽  
Minimum Film Thickness ◽  
Profile Design

Misalignment between the shaft and the bearing of a journal bearing set may be inevitable and can negatively impact journal bearing performance metrics in many industrial applications. This work proposes a convex profile design of the journal surface to help counteract the negative effects caused by such a misalignment. A transient mass-conserving hydrodynamic Reynolds equation model with the Patir–Cheng flow factors and the Greenwood–Tripp pressure–gap relationship is developed to conduct the design and analysis. The results reveal that under transient impulse loading, a properly designed journal profile can help enhance the minimum film thickness, reduce mean and peak bearing frictions, and increase bearing durability by reducing the asperity-related wear load. The mechanism for the minimum film thickness improvement due to the profile design is traced to the more even distribution of the hydrodynamic pressure toward the axial center of the bearing. The reason for the reductions of the friction and wear load is identified to be the decreased asperity contact by changing the lubrication regime from mixed lubrication to nearly hydrodynamic lubrication. Parametric studies and a case study are reported to highlight the key points of the profile design and recommendations for profile height selection are made according to misalignment parameters.

scholarly journals Roughness Effect on Thermo-Elasto-Hydrodynamic Performance of a 170ᵒ -Arc Partial Journal Bearing

2021 ◽  
Vol 27 (1) ◽  
pp. 16-34
Author(s):  
Souad Jabbar Shamal ◽  
Luay Sadiq Al-Ansari ◽  
Ahmed Niameh Mehdy Alhusseny ◽  
Adel Gharib Nasser
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Iterative Solution ◽  
Operating Conditions ◽  
Hydrodynamic Performance ◽  
Temperature Deformation ◽  
Maximum Pressure ◽  
Static Structure ◽  
Scratch Depth ◽  
Wide Range

In the current analysis, the effects of circumferential scratches along the inner surface of a 170ᵒ -arc partial journal bearing has been numerically investigated. Their impact on the thermo-elasto-hydrodynamic performance characteristics, including maximum pressure, temperature, deformation, and stress, has been examined thoroughly. The ANSYS Fluent CFD commercial code was employed to tackle the iterative solution of flow and heat transfer patterns in the fluid film domain. They are then applied to the ANSYS Static Structure solver to compute the deformation and stress resulted in the solid bearing zone. A wide range of operating conditions has been considered, including the eccentricity ratio ( ) and scratch depth ( ). In contrast, the bearing length-diameter ratio (L/D) and the rotation speed (N) have been fixed at 0.77 and 1500 rpm, respectively. The thermo-hydrodynamic pressure, temperature, stress, and deformation have all been computed. It was found that the scratch depth has a direct effect on the thermo-hydrodynamic performance of the partial bearings. Meanwhile, the deep central scratches are important, especially at scratch depth equal to 0.224 mm.

scholarly journals Sensibility Analysis of Design Parameters for Journal Bearings Optimization of Mass Balancing Systems

2005 ◽  
Author(s):  
L. Morais ◽  
L. A. Ferreira
Keyword(s):  
Film Thickness ◽  
Power Loss ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Radial Clearance ◽  
Maximum Pressure ◽  
Minimum Film Thickness ◽  
Mass Balancing ◽  
Sensibility Analysis ◽  
Selection Of

This work presents a sensibility analysis for the journal bearings of combustion engines mass balancing systems. Applying it, it’s possible to improve the journal bearings and avoid possible failures. This analysis consists on studying the effects of the variation of the journal bearings main parameters (radial clearance, journal bearing diameter and journal bearing length) on the journal bearings operating conditions (minimum film thickness, maximum pressure and power loss). The analysis also includes the comparison and selection of the different metallic materials that can be used in these journal bearings, as well as the selection of the lubrication system groove suitable for the journal bearings used in this kind of application. This sensibility analysis shows that: increasing the radial clearance the minimum film thickness increases, the maximum pressure remains approximately the same and the power loss decreases; increasing the journal bearing length, the minimum film thickness and power loss increase and the maximum pressure decreases; increasing the journal bearing diameter, the minimum film thickness and power loss increase and the maximum pressure decreases. At last, it’s found that the white metals (Babbitts) are considered the most advantageous and indicated materials for these journal bearings, and that the lubrication system grooves should be circumferential.

Sign in / Sign up

Export Citation Format

Share Document