scholarly journals Heat Transfer and Pressure Drop Characteristics During R22 Evaporation in an Oval Microfin Tube

2000 ◽  
Vol 123 (2) ◽  
pp. 301-308 ◽  
Author(s):  
Man-Hoe Kim ◽  
Jeong-Seob Shin ◽  
Clark W. Bullard
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Horizontal Tube ◽  
Outer Diameter ◽  
Transfer Coefficients ◽  
Round Tube ◽  
Two Phase ◽  
Axis Ratio ◽  
Oval Tube ◽  
Microfin Tubes

An experimental study on R22 evaporating heat transfer in round and oval microfin tubes has been performed. The oval tube was an elliptic tube of axis ratio 1:1.5, which was fabricated from the round tube with an outer diameter of 9.52 mm and 18 deg helix angle counterclockwise. The test section was a straight horizontal tube of 0.6 m in length and was heated electrically by a tape heater wound on the tube surface. Heat flux of 12 kW/m2 was maintained constant and the range of refrigerant quality was 0.2–0.8. The tests were conducted for evaporation at 15 °C for 30–60 kg/h mass flow rate (mass flux based on the oval tube: 150–300 kg/m2s) and the installation angles of the oval tube were varied between 0 and 135 deg in the circumferential direction. The local and average heat transfer and pressure drop characteristics for the oval tube were compared to those for the baseline round tube. The average two-phase heat transfer coefficients for the oval tube were 2–12 percent higher than that for the round tube and pressure drops for both tubes are similar. The single heat transfer coefficient and friction factor correlations for the round and oval microfin tubes are developed within the rms errors of ±5.6 percent and ±10.0 percent, respectively.

Two-Phase Pressure Drop and Boiling Heat Transfer in a Single Horizontal Microchannel

2006 ◽  
Author(s):  
Cheol Huh ◽  
Moo Hwan Kim
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Local Flow ◽  
Heat Transfer Coefficients ◽  
Phase Pressure

With a single microchannel and a series of microheaters made with MEMS technique, two-phase pressure drop and local flow boiling heat transfer were investigated using deionized water in a single horizontal rectangular microchannel. The test microchannel has a hydraulic diameter of 100 μm and length of 40 mm. A real time observation of the flow patterns with simultaneous measurement are made possible. Tests are performed for mass fluxes of 90, 169, and 267 kg/m2s and heat fluxes of from 100 to 600 kW/m2. The experimental local flow boiling heat transfer coefficients and two-phase frictional pressure gradient are evaluated and the effects of heat flux, mass flux, and vapor qualities on flow boiling are studied. Both the evaluated experimental data are compared with existing correlations. The experimental heat transfer coefficients are nearly independent on mass flux and the vapor quality. Most of all correlations do not provide reliable heat transfer coefficients predictions with vapor quality and prediction accuracy. As for two-phase pressure drop, the measured pressure drop increases with the mass flux and heat flux. Most of all existing correlations of two-phase frictional pressure gradient do not predict the experimental data except some limited conditions.

Local Heat Transfer Coefficients and Pressure Drop During Evaporation in a Smooth Horizontal Tube

2002 ◽  
Author(s):  
C. Aprea ◽  
A. Greco ◽  
G. P. Vanoli
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Local Heat Transfer ◽  
Horizontal Tube ◽  
Local Heat ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

R22 is the most widely employed HCFC working fluid in vapour compression plant. HCFCs must be replaced within 2020. Major problems arise with the substitution of the working fluids, related to the decrease in performance of the plant. Therefore, extremely accurate design procedures are needed. The relative sizing of each of the components of the plant is crucial for cycle performance. For this reason, the knowledge of the new fluids heat transfer characteristics in condensers and evaporators is required. The local heat transfer coefficients and pressure drop of pure R22 and of the azeotropic mixture R507 (R125-R143a 50%/50% in weight) have been measured during convective boiling. The test section is a smooth horizontal tube made of a with a 6 mm I.D. stainless steel tube, 6 m length, uniformly heated by Joule effect. The effects of heat flux, mass flux and evaporation pressure on the heat transfer coefficients are investigated. The evaporating pressure varies within the range 3 ÷10 bar, the refrigerant mass flux within the range 200 ÷ 1000 kg/m2s, the heat flux within 0 ÷ 44 kW/m2. A comparison have been carried out between the experimental data and those predicted by means of the most credited literature relationships.

Evaporation of Ammonia in a Smooth Horizontal Tube: Heat Transfer Measurements and Predictions

1999 ◽  
Vol 121 (1) ◽  
pp. 89-101 ◽  
Author(s):  
O. Zu¨rcher ◽  
J. R. Thome ◽  
D. Favrat
Keyword(s):  
Heat Transfer ◽  
Flow Boiling ◽  
Saturation Temperature ◽  
Local Heat Transfer ◽  
Horizontal Tube ◽  
Steel Tube ◽  
Heat Fluxes ◽  
Stainless Steel Tube ◽  
Transfer Coefficients ◽  
Two Phase

Experimental test results for flow boiling of pure ammonia inside horizontal tubes were obtained for a plain stainless steel tube. Tests were run at a nominal saturation temperature of 4°C, nine mass velocities from 20–140 kg/m2 s, vapor qualities from 1–99 percent and heat fluxes from 5–58 kW/m2. Two-phase flow observations showed that the current test data covered the following regimes: fully stratified, stratified-wavy, intermittent, annular, and annular with partial dryout. The Kattan-Thome-Favrat flow boiling model accurately predicted the local heat transfer coefficients measured in all these flow regimes with only two small modifications to their flow map (to extend its application to G < 100 kg/m2 s). Their flow boiling model was also successfully compared to the earlier ammonia flow boiling data of Chaddock and Buzzard (1986). The Gungor-Winterton (1987) correlation instead gave very poor accuracy for ammonia.

Evaporation Heat Transfer and Pressure Drop in Horizontal Tubes With Strip-Type Inserts Using Refrigerant 600a

1999 ◽  
Vol 122 (2) ◽  
pp. 387-391 ◽  
Author(s):  
S.-S. Hsieh ◽  
K.-J. Jang ◽  
Y.-C. Tsai
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Pressure Drops ◽  
Horizontal Tubes ◽  
Evaporation Heat

Results of a study on saturated boiling heat transfer of refrigerant R-600a in horizontal tubes (ID=10.6 mm) with strip-type inserts (longitudinal strip LS with/without perforated holes and cross-strip CS inserts) are reported. Local heat transfer coefficients are measured for a range of heat flux (9.1∼31.2 kW/m2), mass velocity (8.23∼603.3 kg/m2s), and equilibrium mass quality (⩽0.8) and the influences were studied. The data were compared with the performance of the corresponding smooth tubes. Enhancement factors are presented and discussed. Pressure drop measurement was also conducted and it is found that both single-phase and two-phase pressure drops increase with increasing heat flux levels and mass velocities. [S0022-1481(00)00302-9]

Local Heat Transfer and Pressure Drop for Finned-Tube Heat Exchangers Using Oval Tubes and Vortex Generators

2001 ◽  
Author(s):  
James E. O’Brien ◽  
Manohar S. Sohal ◽  
Philip C. Wallstedt
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Single Channel ◽  
Finned Tube ◽  
Transfer Coefficients ◽  
Conduction Model ◽  
Number Range ◽  
Tube Heat Exchanger ◽  
Oval Tube ◽  
Tube Geometry

Abstract This paper presents the results of an experimental study of forced convection heat transfer in a narrow rectangular duct fitted with an elliptical tube and one or two a delta-winglet pairs. The duct was designed to simulate a single passage in a fin-tube heat exchanger. Heat transfer measurements were obtained using a transient technique in which a heated airflow is suddenly introduced to the test section. High-resolution local fin-surface temperature distributions were obtained at several times after initiation of the transient using an imaging infrared camera. Corresponding local fin-surface heat transfer coefficients were then calculated from a locally applied one-dimensional semi-infinite inverse heat conduction model. Heat transfer results were obtained over a Reynolds number range based on duct height of 670–6300. Pressure drop measurements have also been obtained for similar elliptical-tube and winglet geometries using a separate single-channel, multiple-tube-row pressure-drop apparatus. The pressure-drop apparatus includes four tube rows in a staggered array. Comparisons of heat transfer and pressure drop results for the elliptical tube versus a circular tube with and without winglets are provided. Mean heat transfer results indicated that the addition of the single winglet pair to the oval-tube geometry yielded significant heat transfer enhancement, averaging 38% higher than the oval-tube, no-winglet case. The corresponding increase in friction factor associated with the addition of the single winglet pair to the oval-tube geometry was very modest, less than 10% at ReDh = 500 and less than 5% at ReDh = 5000.

Studies on Condensation of Refrigerants in a High Aspect Ratio Microchannel and in a Novel Micro-Groove Surface Heat Exchanger: Development of Micro-Condensers in Compact Two Phase Cooling Systems

2007 ◽  
Author(s):  
Serguei Dessiatoun ◽  
Sourav Chowdhury ◽  
Ebrahim Al-Hajri ◽  
Edvin Cetegen ◽  
Michael Ohadi
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Temperature Drop ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Groove Surface ◽  
Heat Transfer Coefficients ◽  
Surface Condenser ◽  
Two Phase Cooling

Three different refrigerants, R134a, R245fa and HFE7100 were analyzed as working fluids for two-phase cooling of high heat flux electronics in a 0.7 mm hydraulic diameter 190 mm long high aspect ratio minichannel and in a newly developed micro-groove surface condenser. The latter comprised of a micro-groove surface with rectangular grooves of 84 μm in hydraulic diameter with an aspect ratio of 10.6 and headers that directed the refrigerant flow into the grooves. It was concluded that in the minichannel R245fa provides higher heat transfer coefficients compared to R134a with a significantly higher pressure drop. The saturation temperature drop in the same channel created a significant temperature drop for HFE7100 that make the application of such minichannels for cross-flow condensers with this fluid unpractical. The microgroove surface condenser provided significantly higher heat transfer coefficients compared to the minichannel condenser. The pressure drop in the micro-groove surface condenser was extremely low and imposed just 1C temperature drop on HFE7100 at it highest heat flux. The mass flux of refrigerant in the micro-groove surface condenser is significantly lower compared to conventional mini and microchannel condensers. In its current configuration, the microgroove surface condenser benefits from the possibility of an increase in mass flux resulting in a significant increase in heat transfer coefficient and just a moderate increase in pressure drop.

Heat Transfer and Pressure Drop Simulation of CO2-Hydrate Mixture in Tube

2017 ◽  
Vol 25 (01) ◽  
pp. 1750005 ◽  
Author(s):  
Benedict Prah ◽  
Rin Yun
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Volume Fraction ◽  
Flow Characteristics ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Mixture Flow ◽  
Heat Transfer Coefficients ◽  
Two Phases ◽  
Energy Equations

The formation of CO2 hydrate during CO2 transportation presents a complex two-phase flow within tube. A two-dimensional CFD model for CO2 hydrate mixture flow in tube is derived based on the Eulerian multiphase flow modeling approach in which the two phases consist of CO2 gas and CO2 hydrate particles. A coupled Eulerian multiphase and nonisothermal flow model without phase-change is developed based on COMSOL Multiphysics built-in application modes. The model couples the mass, momentum, and energy equations for the two phases to solve the temperature and flow characteristics of the CO2 hydrate mixture flow in tube. CO2 hydrate particles are found to settle down during flow even under high velocity operation. The pressure drop increased linearly with inlet volume fraction from 1.29[Formula: see text]kPa for 0.1–5.2[Formula: see text]kPa for 0.5, and the related overall heat transfer coefficients of the CO2 hydrate mixture computed from the model ranged from 980 to 4000[Formula: see text]W/m2K with variation of CO2 hydrate volume fraction.

Numerical Simulation of Flow Field and Heat Transfer of Streamlined Cylinders in Crossflow

2005 ◽  
Author(s):  
Zhihua Li ◽  
Jane Davidson ◽  
Susan Mantell
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Circular Cylinder ◽  
Average Nusselt Number ◽  
Stokes Equations ◽  
Local Heat Transfer ◽  
Published Data ◽  
Transfer Coefficients ◽  
Axis Ratio

The use of streamlined tubes to reduce pressure drop across polymer tube bundles is considered because of the relative ease of fabrication. The drag and convective heat transfer coefficients along the outer surface of lenticular and elliptical tubes with minor-to-major axis ratios of 0.3, 0.5, and 0.8 are determined numerically for cross-flow Reynolds numbers from 500 to 10,000. An isothermal surface is assumed. The two-dimensional, unsteady Navier-Stokes equations and energy equation are solved using the finite volume method. Laminar flow is assumed from the front stagnation point up to the point of separation. Turbulent flow in the wake is resolved using the shear stress transport k-omega model. Local heat transfer, pressure and friction coefficients as well as a total drag coefficient and average Nusselt number are presented. The results for streamlined tubes are compared to published data for circular and elliptical cylinders. Drag of the elliptical and lenticular cylinders is similar and lower than a circular cylinder. Reductions in drag may be increased by making the streamlined cylinders more slender. Over the range of Reynolds number considered, an elliptical cylinder with an axis ratio equal to 0.5 reduces pressure drop by 30 to 40 percent compared to that of a circular cylinder. The lenticular and elliptical geometries have nearly identical average of Nusselt number. The average Nusselt number of an elliptical or lenticular cylinder with axis ratio of 0.5 and 0.3 is 15 to 35% lower than that of a circular cylinder. A case study for an automotive radiator is presented to illustrate comparison of shaped and circular tubes in terms of both heat transfer and pressure drop.

Experimental Heat Transfer Coefficient and Pressure Drop during Condensation of R-134a and R-410A in Horizontal Micro-fin Tubes

2018 ◽  
Vol 26 (03) ◽  
pp. 1850022 ◽  
Author(s):  
Sanjeev Singh ◽  
Rajeev Kukreja
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Outer Diameter ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
R 134A ◽  
Fin Tubes

Condensation heat transfer coefficients and pressure drops of HFC refrigerants R-134a and R-410A have been investigated experimentally in smooth and micro-fin tubes (helix angles 18[Formula: see text] and 15[Formula: see text]) of outer diameter 9.52[Formula: see text]mm at mass fluxes from 200 to 600[Formula: see text]kg/m[Formula: see text]s, vapor qualities between 0.1 and 0.9 and at saturation temperatures of 35[Formula: see text]C and 40[Formula: see text]C. Results showed that the heat transfer coefficients of R-134a and R-410A inside micro-fin tubes were 1.21–1.82 and 1.15–1.47 times higher and frictional pressure drops were 2.11–2.56 and 1.62–2.12 times higher than those of smooth tubes. These experimental results are compared with the existing heat transfer and frictional pressure drop correlations proposed by different researchers. The comparison showed fairly good agreement with these existing correlations within [Formula: see text]30%. A new correlation has also been proposed for predicting heat transfer coefficient in micro-fin tubes. The oil concentrations measured for refrigerants R-134a and R-410A varied in the range of 1.3–1.5%, respectively.

A Study of Condensation Heat Transfer in a Single Mini-Tube and a Review of Korean Micro- and Mini-Channel Studies

2003 ◽  
Author(s):  
M. H. Kim ◽  
J. S. Shin ◽  
C. Huh ◽  
T. J. Kim ◽  
K. W. Seo
Keyword(s):  
Heat Transfer ◽  
Flow Boiling ◽  
Flow Characteristics ◽  
Saturation Temperature ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Condensation Heat Transfer ◽  
Transfer Coefficients ◽  
Round Tube ◽  
Two Phase

This paper reviews recent Korean studies of flow characteristics, flow boiling, and flow condensation in micro- and mini-channels. The characteristics of local heat transfer and pressure drops were experimentally investigated using condensing R134a two-phase flow, in a single round tube, with an inner diameter of 0.691 mm. New experimental techniques were developed to measure the condensation heat transfer coefficient. Tests were performed for a mass flux of 100 to 600 kg/m2s, a heat flux of 5 to 20 kW/m2, and a saturation temperature of 40°C. The experimental local condensation heat transfer coefficients and two-phase frictional pressure gradients are shown. Comparisons of experimental data with existing models reveal that the correlations failed to predict the present data. This study contains the unique sub-millimeter-diameter, single round tube, condensation data reported in the literature.

Sign in / Sign up

Export Citation Format

Share Document