Dynamic Response of a Planetary Gear System Using a Finite Element/Contact Mechanics Model

1999 ◽  
Vol 122 (3) ◽  
pp. 304-310 ◽  
Author(s):  
Robert G. Parker ◽  
Vinayak Agashe ◽  
Sandeep M. Vijayakar
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Planetary Gear ◽  
Contact Forces ◽  
Gear System ◽  
Element Formulation ◽  
Time Step ◽  
Wide Range ◽  
Planetary Gear System ◽  
Mode Response

The dynamic response of a helicopter planetary gear system is examined over a wide range of operating speeds and torques. The analysis tool is a unique, semianalytical finite element formulation that admits precise representation of the tooth geometry and contact forces that are crucial in gear dynamics. Importantly, no a priori specification of static transmission error excitation or mesh frequency variation is required; the dynamic contact forces are evaluated internally at each time step. The calculated response shows classical resonances when a harmonic of mesh frequency coincides with a natural frequency. However, peculiar behavior occurs where resonances expected to be excited at a given speed are absent. This absence of particular modes is explained by analytical relationships that depend on the planetary configuration and mesh frequency harmonic. The torque sensitivity of the dynamic response is examined and compared to static analyses. Rotational mode response is shown to be more sensitive to input torque than translational mode response. [S1050-0472(00)00403-7]

The Fault Characteristics of Planetary Gear System with Tooth Breakage

2013 ◽  
Vol 569-570 ◽  
pp. 489-496 ◽  
Author(s):  
Yong Gui ◽  
Qin Kai Han ◽  
Zheng Li ◽  
Zhi Ke Peng ◽  
Fu Lei Chu
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Planetary Gear ◽  
Transmission System ◽  
Gear Transmission ◽  
Gear System ◽  
Operation Conditions ◽  
Gear Transmission System ◽  
Planetary Gear System ◽  
Two Parameters

Tooth breakage is a typical failure form of wind-turbine planetary gear transmission system, it is important to study the influence of tooth breakage on vibration characteristics of planetary gear transmission system. In this paper, considering the tooth breakage defect, a lumped parameter vibration model of a planetary gear system with time-periodic mesh stiffness is established. Effects of the length and width of tooth breakage on meshing stiffness and dynamic response are discussed in detail. The relation between characteristic frequency of the tooth breakage fault and rotating speeds is pointed out. Several statistical indicators are utilized to show the influence of two parameters (length of planet tooth breakage and input speed) on the dynamic response of the system. Experiments are carried out to verify the simulation results. These results would be useful for fault diagnosis of wind turbine transmission system at different operation conditions.

Study of Dynamic Model of Helical/Herringbone Planetary Gear System With Friction Excitation

2018 ◽  
Vol 13 (12) ◽  
Author(s):  
Shaoshuai Hou ◽  
Jing Wei ◽  
Aiqiang Zhang ◽  
Teik C. Lim ◽  
Chunpeng Zhang
Keyword(s):  
Dynamic Response ◽  
Dynamic Model ◽  
Great Influence ◽  
Elastohydrodynamic Lubrication ◽  
Planetary Gear ◽  
Gear System ◽  
Frictional Torque ◽  
Vibration Acceleration ◽  
Tooth Surfaces ◽  
Planetary Gear System

Tooth friction is unavoidable and changes periodically in gear engagement. Friction excitation is an important excitation source of a gear transmission system. They are different than the friction coefficients of any two points on the same contact line of a helical/herringbone gear. In order to obtain the influence of the friction excitation on the dynamic response of a helical/herringbone planetary gear system, a method that uses piecewise solution and then summing them to analyze the friction force and frictional torque of tooth surfaces is proposed. Then, the friction coefficient is obtained based on the mixed elastohydrodynamic lubrication (EHL) theory. A dynamic model of a herringbone planetary gear system is established considering the friction, mesh stiffness, and meshing error excitation by the node finite element method. The influence of friction excitation on the dynamic response of the herringbone planetary gear is studied under different working conditions. The results show that friction excitation has a great influence on the vibration acceleration of the sun and planetary gear. However, the effect on the radial and tangential vibration acceleration of a planetary gear is the opposite. In addition, the friction excitation has a slight effect on the meshing force.

An analyzing method of coupled modes in multi-stage planetary gear system

2014 ◽  
Vol 15 (11) ◽  
pp. 2357-2366 ◽  
Author(s):  
Wei Sun ◽  
Xin Ding ◽  
Jing Wei ◽  
Xinglong Hu ◽  
Qingguo Wang
Keyword(s):  
Planetary Gear ◽  
Gear System ◽  
Coupled Modes ◽  
Multi Stage ◽  
Planetary Gear System

Analysis of nonlinear dynamic characteristic of a planetary gear system considering tooth surface friction

2021 ◽  
pp. 135065012199174
Author(s):  
Jingyue Wang ◽  
Ning Liu ◽  
Haotian Wang ◽  
Jiaqiang E
Keyword(s):  
Damping Ratio ◽  
Excitation Frequency ◽  
Planetary Gear ◽  
Gear System ◽  
Tooth Surface ◽  
Lumped Mass ◽  
Heavy Load ◽  
Light Load ◽  
Planetary Gear System ◽  
Bifurcation Behavior

Based on the lumped mass method, a torsional vibration model of the planetary gear system is established considering the nonlinear factors such as friction, time-varying meshing stiffness, backlash, and comprehensive error. The Runge–Kutta numerical method is used to analyze the motion characteristics of the system with various parameters and the influence of tooth friction on the bifurcation and chaos characteristics of the system. The numerical simulation results show that the system has rich bifurcation behavior with the excitation frequency, damping ratio, comprehensive error amplitude, load and backlash, and experiences multiple periodic motion and chaotic motion. Tooth friction makes the bifurcation behavior of the system fuzzy in the high frequency and heavy load areas, makes the chaos of the system restrained in the low-damping ratio and light load areas, advances the bifurcation point of the system in the small comprehensive error amplitude area, and makes the period window of the chaos area larger in the large-backlash area, which makes the bifurcation behavior of the system more complex.

The Finite Element Analysis of Dynamic Interaction of High-Speed Shinkansen, the Rail, and Bridge

1993 ◽  
Author(s):  
Makoto Tanabe ◽  
Hajime Wakui ◽  
Nobuyuki Matsumoto
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
High Speed ◽  
Response Analysis ◽  
Element Formulation ◽  
Element Analysis ◽  
Finite Element Program ◽  
The Finite Element Analysis ◽  
Element Program ◽  
The Impact

Abstract A finite element formulation to solve the dynamic behavior of high-speed Shinkansen cars, rail, and bridge is given. A mechanical model to express the interaction between wheel and rail is described, in which the impact of the rail on the flange of wheel is also considered. The bridge is modeled by using various finite elements such as shell, beam, solid, spring, and mass. The equations of motions of bridge and Shinkansen cars are solved under the constitutive and constraint equations to express the interaction between rail and wheel. Numerical method based on a modal transformation to get the dynamic response effectively is discussed. A finite element program for the dynamic response analysis of Shinkansen cars, rail, and bridge at the high-speed running has been developed. Numerical examples are also demonstrated.

Effect of the bearing clearance on vibrations of a double-row planetary gear system

2019 ◽  
Vol 234 (2) ◽  
pp. 347-357
Author(s):  
Jing Liu ◽  
Shizhao Ding ◽  
Linfeng Wang ◽  
Hongwu Li ◽  
Jin Xu
Keyword(s):  
Contact Stiffness ◽  
Planetary Gear ◽  
Gear Ratio ◽  
Gear System ◽  
Double Row ◽  
External Torque ◽  
Bearing Clearance ◽  
Gear Systems ◽  
Planetary Gear System ◽  
Stiffness And Damping

The bearing clearance, external torque, and input speed can greatly affect vibrations of the planetary gear system. The double-row planetary gear systems are commonly used in the gearbox of special vehicles, which are the key parts to obtain a larger gear ratio. Although many works have been presented to study those factors on vibrations of the single-row planetary gear system, a few works were focused on vibrations of the double-row planetary gear system with the bearing clearance. To overcome this problem, a multi-body dynamic model of a double-row planetary gear system with six planet bearings and one supported bearing of the sun gear is presented. This model is the main part of a gear box transmission system. The new model is developed for studying the effect of the bearing clearance on the planetary system. The meshing stiffness and damping between the gears are obtained by current methods in the listed references, as well as the contact stiffness and damping in bearings. The liner stiffness and damping model is used. The effects of the bearing clearance, external torque, and input speed on vibrations of the system are analyzed. The results show that vibrations of the ring gear and sun gear decrease with the increment of the external torque and increase with the increment of the input speed. Moreover, a reasonable bearing clearance can be helpful for reducing system vibrations for some mating external torque and input speed conditions. The results can provide some guidance to find new method to reduce vibrations and increase the service life of planetary gear systems.

Sign in / Sign up

Export Citation Format

Share Document