PREPARATION AND CHARACTERIZATION OF PLASTICIZED POLYLACTIC ACID/STARCH BLEND

2016 ◽  
Vol 78 (11-2) ◽  
Author(s):  
Fathilah Ali ◽  
Raina J.Awale ◽  
Mohamed Elwathig Saeed Mirghani ◽  
Hazleen Anuar ◽  
Norasikin Samat
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Polylactic Acid ◽  
Mechanical And Thermal Properties ◽  
Melt Blending ◽  
Infra Red ◽  
Long Time ◽  
Ft Ir ◽  
The Cost

Petroleum based packaging materials has raised environmental concerns due to its non-environmentally friendly degradation. Conventional plastic takes a long time to degrade and remains in the waste dump. Since then, attention to biodegradable plastics has been heightened for its greener degradation. Polylactic acid (PLA) is a renewable polymer with mechanical properties comparable to those of the conventional plastics. This study aims to improve the mechanical and thermal properties and reducing the cost of PLA production by blending PLA with starch as filler and epoxy palm oil (EPO) as plasticizer. The PLA/starch/EPO blends were prepared by solution casting and melt blending methods and properties of the blends were studied and characterized. The thermal properties of plasticized PLA/starch were investigated by Differential Screening Calorimetry (DSC) followed by Fourier Transform Infra-Red Spectroscopy (FT-IR) in order to observe the degree of interaction of plasticized PLA/starch blend. The mechanical properties were investigated using Universal Tensile Test

Preparation and Characterization of GNP/Nylon Composites

2014 ◽  
Vol 556-562 ◽  
pp. 339-342 ◽  
Author(s):  
Bao Feng Xu ◽  
Zhi Dan Lin ◽  
Jiang Ming Chen ◽  
Jun Lin
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Properties ◽  
Graphene Nanoplatelets ◽  
Melt Blending ◽  
Blending Method

Graphene nanoplatelets (GNP) and nylon (PA) have been often used as thermal filler and matrix and respectively to produce composites. In this work, PA6/PA66/GNP thermal composites were prepared via a melt blending method. Mechanical properties, morphology, and thermal properties of PA6/PA66/GNP composites were investigated. Because the GNP is very expensive, we investigated to use Al2O3 and graphite and examined the characteristics of the prepared composites. Thermal conductivity values of PA6/PA66/GNP composites remarkably increased with increase of GNP contents mainly via layered dispersion in nylon matrix. The thermal conductivity of composite containing 50 wt % of GNP was measured as 5.03 W·m–1·K–1 at 30 °C, indicating an increase of more than 15 times compared with that of the neat PA6. When the Al2O3 was replaced for GNP, the thermal conductivity of composites decreased, but the mechanical properties improved. When graphite was used to replace for GNP, thermal conductivity basically remained unchanged but mechanical properties decreased.

Effect of chain extender on the mechanical and thermal resistance properties of polyurethane liners for composite propellants

Polyurethanes ◽  
2016 ◽  
Vol 1 (1) ◽  
Author(s):  
P. Ross ◽  
G. Sevilla ◽  
J. Quagliano
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Chain Extender ◽  
Molecular Structures ◽  
Polymer Chains ◽  
Mechanical And Thermal Properties ◽  
Thermal Changes ◽  
Ft Ir ◽  
Chain Lengths

AbstractPolyurethane formulations utilized as liners for composite propellants were prepared by the reaction of toluene-2,4-diisocyanate (TDI) and isophorone diisocyanate (IPDI) with hydroxyl terminated polybutadiene (HTPB), while polymer chains were further extended with neopentyl glycol diol, NPG triol and two different triols (monoglyceryl ricinoleate, MRG and trimethylolpropane, TMP). Liners were formulated with micronized titanium dioxide mechanically dispersed in hydroxyl-terminated polybutadiene (HTPB). The molecular structures of liners were confirmed by FT-IR. Thermal properties indicated that the nature of chain extender (crosslinker) only slightly affected the temperatures for decomposition of liners. Two main thermal changes were found at 370∘C and another at around 440–500∘C, depending on the chain extender utilized. On the other side, mechanical properties varied within the range of 0,7-1,8 MPa, consistent with this kind of elastomers. Tensile strength at break was only significantly affected with TMP and MRG-chain extended liners at the lowest concentrations tested of 1,3 and 2% (w/w), respectively. However, the behaviour depended on whether TDI or IPDI isocyanate was utilized for curing. TMP 1,3% crosslinked liner cured with TDI had a tensile strength of 1,82MPa whileMRG-crosslinked liner cured with IPDI had a tensile strength of 1,56 MPa. It was observed that at the higher NCO/OH ratios essayed, tensile strength and hardness increased, improving mechanical properties. Our results confirmed that TMP and MRG triols together with NPG diols can be used to tailor mechanical and thermal properties of liners, considering their different hydroxyl functionalities and chain lengths.

Preparation and Characterization of Polylactic Acid/Acetate Starch Blends with Tetrabutyl Titanate

2011 ◽  
Vol 284-286 ◽  
pp. 1750-1755
Author(s):  
Jin Zhou Chen ◽  
Zhen Gao ◽  
Peng Ping Xie ◽  
Kai Guo ◽  
Ming Jun Niu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Flow Rate ◽  
Tetrabutyl Titanate ◽  
Melt Flow ◽  
Melt Flow Rate ◽  
Triethyl Citrate ◽  
Starch Blends ◽  
The Cost

In order to reduce the cost of the polylactic acid (PLLA) material and to improve its flexibility to expand the application of PLA-based plastic, a series of PLLA/SA blends with tetrabutyl titanate (Ti(OBu)4) used as compatibilizer were prepared in the presence of 10% triethyl citrate (TEC) as plasticizer. It was investigated the effect of the compatibilizer and its content on the mechanical properties, structure and morphologies, heat-resistant performance, melt flow rate, and water-resistant performance and other implications of blends. The results showed that: adding the compatibilizer Ti(OBu)4 could significantly improve the compatibility of PLLA and SA, the mechanical properties and thermal stability of the blends were increased, while melt flow rate and water absorption were decreased. When the content of compatibilizer Ti(OBu)4 was 8 wt%, PLA/SA blends(75/25 wt%) had the best overall performance.

Effects of Fiber Surface Treatment on Mechanical and Thermal Properties of Coir-MCC/Polylactic Acid Composites

2012 ◽  
Vol 488-489 ◽  
pp. 638-642 ◽  
Author(s):  
Tanawat Tayommai ◽  
Duangdao Aht-Ong
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Surface Treatment ◽  
Polylactic Acid ◽  
Natural Fiber ◽  
Fiber Surface ◽  
Mechanical And Thermal Properties ◽  
Coir Fibers ◽  
Twin Screw ◽  
Fiber Surface Treatment

Biodegradable plastic reinforced natural fiber composites are finding applications in many fields ranging from construction industry to food industry. The use of natural bio based fillers as reinforcements in composites has several advantages over inorganic fillers including lower density, renewability, and biodegradability. In this research, polylactic acid (PLA)/ microcrystalline cellulose (MCC) composites were investigated as a means to reduce the material cost and enhance the material properties. The coir fibers were used to prepare microcrystalline. Subsequently, the prepared MCC was treated with 3-amiopropyl triethoxysilane (APS) to improve interfacial adhesion between fiber and polymer matrix. Treated and untreated MCC were then mixed at 0-10 wt.% with PLA by twin-screw extruder and fabricated into test specimens by compression molding. The effects of MCC loading and surface treatment on morphology, mechanical properties, and thermal properties of PLA/MCC composites were investigated. The results showed that the PLA with 5 wt.% of MCC exhibited the best mechanical properties compared with all prepared composites. Thermal stability of PLA composites were decreased with increasing MCC content but it can be improved by treated the MCC with APS.

Preparation and characterization of biodegradable blends of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) and poly(butylene adipate-co-terephthalate)

2016 ◽  
Vol 36 (5) ◽  
pp. 473-480 ◽  
Author(s):  
Min Zhang ◽  
Xiaoqian Diao ◽  
Yujuan Jin ◽  
Yunxuan Weng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Crystallization Temperature ◽  
Molecular Interaction ◽  
Mechanical And Thermal Properties ◽  
Elongation At Break ◽  
Tear Strength ◽  
Biodegradable Blends

Abstract Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH) was blended with poly(butylene adipate-co-terephthalate) (PBAT) by extrusion at different weight ratios (PHBH/PBAT: 100:0, 80:20, 60:40, 50:50, 40:60, 20:80 and 0:100). Films were then prepared from the blends and characterized in terms of their morphological, rheological, mechanical and thermal properties. The morphological and rheological results indicated that PHBH/PBAT blends are immiscible but exhibit possible molecular interaction. The crystallization temperature of PHBH in the blends decreased, indicating that the addition of PBAT inhibited the crystallization of PHBH. Blending PBAT with PHBH improved the processability compared with that of pure polymers. The mechanical properties, including tensile strength, elongation at break and tear strength, increased with increasing PBAT content. The PHBH/PBAT 20:80 blend exhibited significantly improved mechanical properties, which was due to the reinforcing and toughening effect of the finely dispersed PHBH phase.

Effect of maleic anhydride grafted polylactic acid concentration on mechanical and thermal properties of thermoplasticized starch filled polylactic acid blends

2021 ◽  
pp. 096739112110041
Author(s):  
Shakti Chauhan ◽  
N Raghu ◽  
Anand Raj
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Maleic Anhydride ◽  
Polylactic Acid ◽  
Coupling Agent ◽  
Thermo Gravimetric Analysis ◽  
Mechanical Analysis ◽  
Strength Properties ◽  
Mechanical And Thermal Properties ◽  
Gravimetric Analysis

Polylactic acid (PLA) is blended with native starch or thermo plasticized starch (TPS) for preparing biodegradable composites. However, poor compatibility of PLA with starch results in the composites with inferior mechanical properties. This study examines the effect of Maleic Anhydride-Grafted-PLA (GMAPLA) coupling agent and its concentration on the extent of improvements in mechanical and thermal properties of PLA –TPS blends. Maleic anhydride was grafted on PLA in Haake torque rheometer, characterized and used as the coupling agent. PLA/TPS (wt/wt) blends (70/30 and 50/50) were prepared by twin screw extrusion. GMAPLA at three different levels 5%, 10% and 15% (wt%) with respect to PLA content was taken to study its effect on mechanical properties of blends. Presence of GMAPLA significantly improved the mechanical properties (tensile, flexural and impact strength) of TPS/PLA blends. Among the three concentrations, 10% GMAPLA in the blend was found to give the maximum improvement in strength properties. Dynamic mechanical analysis and thermo-gravimetric analysis indicated no significant effect of GMAPLA content on transition temperatures and thermal degradation behavior of the blends.

Effect of Algerian Halloysite on the Mechanical and Thermal Properties of Starch-Grafted-Polyethylene Nanocomposites

2018 ◽  
Vol 762 ◽  
pp. 192-196 ◽  
Author(s):  
Walid Fermas ◽  
Remo Merijs Meri ◽  
Mustapha Kaci ◽  
Janis Zicans
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Melt Flow Index ◽  
Halloysite Nanotubes ◽  
Polymer Chains ◽  
Flow Index ◽  
Mechanical And Thermal Properties ◽  
Melt Compounding

This paper deals with the characterization of the physico-mechanical properties of starch-grafted-polyethylene (Starch-g-PE)/unmodified Algerian halloysite nanotubes (HNT) nanocomposites prepared by melt compounding. The nanoclay was incorporated at various filler contents, i.e., 1.5, 3 and 5 wt%. Rheological and tensile properties of the nanocomposites were evaluated by different techniques and the results obtained are compared with those of virgin Starch-g-PE matrix. The study shows a decrease in melt flow index (MFI) values upon increasing the HNT content, which indicates a restriction in the polymer chains mobility due to the confinement effect of HNT. Further, a tensile strength is also improved.

Mechanical and thermal characterization of grafted PP-NCC nanocomposites

2019 ◽  
pp. 089270571987822
Author(s):  
Saud Aldajah ◽  
Mohammad Y Al-Haik ◽  
Waseem Siddique ◽  
Mohammad M Kabir ◽  
Yousef Haik
Keyword(s):  
Thermal Properties ◽  
Interfacial Adhesion ◽  
Thermal Characterization ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Three Point Bending ◽  
Twin Screw ◽  
Thermal Stability Of

This study reveals the enhancement of mechanical and thermal properties of maleic anhydride-grafted polypropylene (PP- g-MA) with the addition of nanocrystalline cellulose (NCC). A nanocomposite was manufactured by blending various percentages of PP, MA, and NCC nanoparticles by means of a twin-screw extruder. The influence of varying the percentages of NCC on the mechanical and thermal behavior of the nanocomposite was studied by performing three-point bending, nanoindentation, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and Fourier-transform infrared (FTIR) spectroscopy tests. The novelty of this study stems on the NCC nanoparticles and their ability to enhance the mechanical and thermal properties of PP. Three-point bending and nanoindentation tests revealed improvement in the mechanical properties in terms of strength, modulus, and hardness of the PP- g-MA nanocomposites as the addition of NCC increased. SEM showed homogeneity between the mixtures which proved the presence of interfacial adhesion between the PP- g-MA incorporated with NCC nanoparticles that was confirmed by the FTIR results. DSC and TGA measurements showed that the thermal stability of the nanocomposites was not compromised due to the addition of the coupling agent and reinforced nanoparticles.

scholarly journals Development of PE/PCL Bilayer Films Modified with Casein and Aluminum Oxide

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3090
Author(s):  
Anita Ptiček Siročić ◽  
Ana Rešček ◽  
Zvonimir Katančić ◽  
Zlata Hrnjak-Murgić
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Water Vapor ◽  
Aluminum Oxide ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Mechanical And Thermal Properties ◽  
Oxide Compound ◽  
Bilayer Films ◽  
Oxide Particles

The studied samples were prepared from polyethylene (PE) polymer which was coated with modified polycaprolactone (PCL) film in order to obtain bilayer films. Thin PCL film was modified with casein/aluminum oxide compound to enhance vapor permeability as well as mechanical and thermal properties of PE/PCL films. Casein/aluminum oxide modifiers were used in order to achieve some functional properties of polymer film that can be used in various applications, e.g., reduction of water vapor permeability (WVTR) and good mechanical and thermal properties. Significant improvement was observed in mechanical properties, especially in tensile strength as well as in water vapor values. Samples prepared with aluminum oxide particles indicated significantly lower values up to 60%, and samples that were prepared with casein and 5% Al2O3 showed the lowest WVTR value.

Sign in / Sign up

Export Citation Format

Share Document