THE EFFECT OF OIL PALM ASH INCORPORATION IN FOAMED CONCRETE

2015 ◽  
Vol 75 (5) ◽  
Author(s):  
Farah A. Hadi ◽  
Hanizam Awang ◽  
Muhammed Zuhear Almulali
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Oil Palm ◽  
Drying Shrinkage ◽  
Target Density ◽  
Concrete Mix ◽  
Different Ages ◽  
Foamed Concrete ◽  
Oil Palm Ash ◽  
Enhanced Properties

This paper investigates the effect of replacing different portions of cement by fine oil palm ash (FOPA). A target density of 1000 kg/m3 was used for the foamed concrete mixes. A foamed concrete mix of 1 part binder, 2 parts filler and 0.45 part of water has been used. Cement was replaced at levels of 25, 35, 45, 55 and 65% by weight of binder. The compressive strength, density, water absorption, drying shrinkage and sorptivity were tested at different ages. The mix containing 25% of fine OPA showed enhanced properties in comparison to the control mix at the age of 90 days. The mixed showed higher compressive strength, less water absorption, increased density and lesser sorptivity. However, the same mix showed higher shrinkage readings than that of the control mix. 

scholarly journals Enhancement of Durability Properties and Drying Shrinkage of Heat-treated Oil Palm Shell Species High-strength Lightweight Concrete

2018 ◽  
Vol 1 (1) ◽  
Author(s):  
Mingkun Yew ◽  
Mingchian Yew ◽  
Lip Huat Saw ◽  
Siongkang Lim ◽  
Jing Hang Beh ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Compressive Strength ◽  
Water Absorption ◽  
Oil Palm ◽  
Lightweight Concrete ◽  
Drying Shrinkage ◽  
Durability Properties ◽  
Palm Shell ◽  
Oil Palm Shell ◽  
Heat Treated

In this study, the effects of heat-treated and non-treated oil palm shell (OPS) species (dura and tenera) are investigated on the slump, density and compressive strength of oil palm shell concrete (OPSC). Two different species of OPS coarse aggregates are subjected to heat treatment at 65 and 130 °C with the duration of 1 h. The results show that the workability of the OPSC increases significantly with an increase in temperature of heat-treated of the tenera OPS aggregates. It is found that the maximum achievable 28-days and 180-days compressive strength is 51 and 54 MPa, respectively. Furthermore, rapid chloride penetration tests (RCPT), porosity measurement and water absorption tests were performance to signify the effects of heat treatment on different OPS species lightweight concrete (LWC). The use of heat-treated OPS LWC induced the advantageous of reducing the permeability and capillary porosity as well as water absorption. The results showed that the ideal of heat treatment method has enhanced the performance of drying shrinkage. Hence, the findings of this study are of primary importance as they revealed that the heat treatment on OPS species LWC can be used as a new environmentally friendly method to enhance the durability properties and drying shrinkage of OPS LWC.

scholarly journals Performance Evaluation and Microstructure Characterization of Metakaolin-Based Geopolymer Containing Oil Palm Ash

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Abideng Hawa ◽  
Danupon Tonnayopas ◽  
Woraphot Prachasaree
Keyword(s):  
Compressive Strength ◽  
Oil Palm ◽  
Raw Materials ◽  
Drying Shrinkage ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Molar Ratios ◽  
Heat Curing ◽  
Oil Palm Ash ◽  
Xrd Patterns

This study reports on the microstructure, compressive strength, and drying shrinkage of metakaolin (MK) based geopolymers produced by partially replacing MK by oil palm ash (OPA). The OPA was used as raw material producing different molar ratios of SiO2/Al2O3and CaO/SiO2. The geopolymer samples were cured at 80°C for 1, 2, or 4 hours and kept at ambient temperature until testing. The compressive strength was measured after 2, 6, and 24 hours and 7 and 28 days. The testing results revealed that the geopolymer with 5% OPA (SiO2 : Al2O3 = 2.88 : 1) gave the highest compressive strength. Scanning electron microscopy (SEM) indicated that the 5% OPA sample had a dense-compact matrix and less unreacted raw materials which contributed to the higher compressive strength. In the X-ray diffraction (XRD) patterns, the change of the crystalline phase after heat curing for 4 hours was easily detectable compared to the samples subjected to a shorter period of heat curing.

scholarly journals Enhancement of Durability Properties and Drying Shrinkage of Heat-treated Oil Palm Shell Species High-strength Lightweight Concrete

2018 ◽  
Vol 2 (1) ◽  
Author(s):  
Mingkun Yew ◽  
Mingchian Yew ◽  
Lip Huat Saw ◽  
Siongkang Lim ◽  
Jing Hang Beh ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Compressive Strength ◽  
Water Absorption ◽  
Oil Palm ◽  
Lightweight Concrete ◽  
Drying Shrinkage ◽  
Durability Properties ◽  
Palm Shell ◽  
Oil Palm Shell ◽  
Heat Treated

In this study, the effects of heat-treated and non-treated oil palm shell (OPS) species (dura and tenera) are investigated on the slump, density and compressive strength of oil palm shell concrete (OPSC). Two different species of OPS coarse aggregates are subjected to heat treatment at 65 and 130 °C with the duration of 1 h. The results show that the workability of the OPSC increases significantly with an increase in temperature of heat-treated of the tenera OPS aggregates. It is found that the maximum achievable 28-days and 180-days compressive strength is 51 and 54 MPa, respectively. Furthermore, rapid chloride penetration tests (RCPT), porosity measurement and water absorption tests were performance to signify the effects of heat treatment on different OPS species lightweight concrete (LWC). The use of heat-treated OPS LWC induced the advantageous of reducing the permeability and capillary porosity as well as water absorption. The results showed that the ideal of heat treatment method has enhanced the performance of drying shrinkage. Hence, the findings of this study are of primary importance as they revealed that the heat treatment on OPS species LWC can be used as a new environmentally friendly method to enhance the durability properties and drying shrinkage of OPS LWC.

scholarly journals Utilisation of Oil Palm Fibre Biomass Waste as Additives in Foamed Concrete

2021 ◽  
Vol 29 (4) ◽  
Author(s):  
Md Azree Othuman Mydin
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Oil Palm ◽  
Construction Materials ◽  
Pulse Velocity ◽  
Biomass Waste ◽  
Foamed Concrete ◽  
Oil Palm Fibre ◽  
Palm Fibre

Worldwide, the construction industry has acknowledged the future demand for lightweight construction materials, with high workability, self-compacting, and environmentally friendly. Given this demand, recent innovative material namely foamed concrete (FC), has been found to reduce normal concrete’s weight potentially. However, while FC made with Ordinary Portland Cement has good compressive strength, other characteristics such as tension are relatively weak given the number of micro-cracks. Therefore, the study focused on the potential use of oil palm fibres in FC regarding their durability and mechanical properties. Notably, one of the major issues faced in the construction of reinforced FC is the corrosion of reinforcing steel which affects the behaviour and durability of concrete structures. Hence, in this study, oil palm fibres were added to improve strength and effectively reduce corrosion. Five types of fibre generated from oil palm waste were considered: oil palm trunk, oil palm frond, oil palm mesocarp and empty fruit bunch consisting of the stalk and spikelets. Specimens with a density of 1800 kg/m3 were prepared in which the weight fraction of the fibre content was kept constant at 0.45% for each mixture. Testing ages differed in testing and evaluating the parameters such as compressive strength, flexural strength, tensile strength, porosity, water absorption, drying shrinkage and ultrasonic pulse velocity. The results showed that the incorporation of oil palm fibre in FC helped reduce water absorption, porosity and shrinkage while enhancing the compressive, flexural and tensile strength of FC.

scholarly journals Effect of Curing Method on Properties of Lightweight Foamed Concrete

2018 ◽  
Vol 7 (2.29) ◽  
pp. 927 ◽  
Author(s):  
Bishir Kado ◽  
Shahrin Mohammad ◽  
Yeong Huei Lee ◽  
Poi Ngian Shek ◽  
Mariyana Aida Ab Kadir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Precast Concrete ◽  
Construction Materials ◽  
Splitting Tensile Strength ◽  
Structural Members ◽  
Lightweight Construction ◽  
Foamed Concrete ◽  
Curing Method

Lightweight construction is aimed to achieve a sustainable feature by reducing transportation frequency and construction materials usage during construction phase. Lightweight precast concrete may serve an alternative for the lightweight construction. There are rarely application can be found for structural members as lightweight panels always to be used for secondary or non-load bearing members. This paper presents an experimental study on properties (compressive strength, splitting tensile strength, water absorption) of lightweight foamed concrete (LFC) at two different curing methods. LFC with densities of 1500, 1700, and 1800 kg/m3, cement-sand ratio of 2:1 and water-cement ratio of 0.5 were investigated. The results showed LFC can be produced with the properties ofdensity range of 1500 to 1800 kg/m3 and corresponding compressive strength of 10 to 39 MPa. The higher the density of LFC, the less the water absorption for all the curing method considered, the highest and the lowest water absorption was 11.3% and 2.0% for 1500 kg/m3 cured in water and 1800 kg/m3 cured in air respectively. Compressive strength of LFC increases with age and density while water cured LFC has high compressive strength. Splitting tensile strength increases with density of LFC, but air cured LFC has more splitting tensile strength than water cured of the same density. The highest splitting tensile strength recorded was 3.92 MPa for 1800 kg/m3 cured in air, which was about 16% of its compressive strength at 28 days of curing age. These properties are important and can be applied to LFC precast structural members with air or water curing method which have less references for LFC in structural usage.  

scholarly journals WATER ABSORPTION AND DRYING SHRINKAGE OF RECYCLED FOAMED AGGREGATE CONCRETE

2018 ◽  
Vol 30 (3) ◽  
Author(s):  
Chai Teck Jung ◽  
Tang Hing Kwong ◽  
Koh Heng Boon
Keyword(s):  
Water Absorption ◽  
Absorption Rate ◽  
Drying Shrinkage ◽  
Casting Process ◽  
Concrete Specimen ◽  
Sieve Analysis ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Water Absorption Rate ◽  
Foamed Concrete

Abstract: This paper presents some experimental results and discusses the used of recycled foamed aggregates as natural coarse aggregates replacement in producing concrete. The physical properties of recycled foamed aggregates concrete were investigated. The properties studied are water absorption and drying shrinkage from the concrete early ages until the periods of 56 days. The 100 mm x 100 mm cube specimen was used to study the water absorption at the age of 7, 28 and 56 days. Meanwhile, the 100 mm x 100 mm x 300 mm length prism had been casted and used for drying shrinkage test for recycled foamed aggregates concrete. The foamed aggregates was produced from crushing recycled foamed concrete blocks. It were coated with cement paste to reduce its water absorption ability during casting process. Superplasticizer was used to maintain the workability of fresh concrete with a slump vary between 50 mm to 100 mm. The physical tests were conducted on recycled foamed aggregates to determine their initial properties such as loose bulk density, sieve analysis and water absorption rate. Recycled foamed aggregate concretes were produced with varied water cement ratio. The results obtained indicated that the linear elastic relationship between water cement ratio and water absorption rate. The higher the water cement ratio of concrete specimen will obtained higher water absorption rate. Vice versa, the density is low for drying shrinkage. The water absorption decreased while drying shrinkage becomes more stabilized over curing period.

scholarly journals Influences of shrinkage reducing admixture on the mechanical properties, drying shrinkage, water absorption and porosity of Portland cement mortar

2021 ◽  
Vol 15 (3) ◽  
pp. 55-67
Author(s):  
Nguyen Van Chinh
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Portland Cement ◽  
Water Absorption ◽  
Drying Shrinkage ◽  
Effective Porosity ◽  
Minor Effect ◽  
Wide Range ◽  
Shrinkage Reducing Admixture ◽  
A Minor

Drying shrinkage is the main cause of early age cracking of concrete and mortar. A wide range of research has been conducted to reduce the drying shrinkage, including using fibres or chemical admixtures. This paper investigated the effect of shrinkage reducing admixture on the flexural strength, compressive strength, drying shrinkage, water absorption and porosity of mortar. The mix compositions were ordinary Portland cement (OPC) : sand : liquid = 1: 1: 0.38 in which liquid consisted of water and shrinkage reducing admixture (SRA). SRA was used at the proportions of 2%, 4%, and 7% by weight of cement. The test results show that SRA reduces the flexural and compressive strengths of mortar. The reduction in flexural strength and compressive strength at 28 days is 14% and 25%, respectively at 7% SRA dosage. In addition, SRA significantly reduces the drying shrinkage and water absorption of mortar. At 7% SRA dosage, the drying shrinkage at 53 days is reduced by 60% while the water absorption rate at 24 hours is reduced by 54%. However, SRA has a minor effect on the pore size distribution, effective porosity, and cumulative intrusion volume of mortar.

Preparation and Characterization of CCCW/Foamed Concrete Composite

2011 ◽  
Vol 261-263 ◽  
pp. 13-18
Author(s):  
Ke Qing Li ◽  
De Ping Chen ◽  
Shi Li Zhang ◽  
Bao Shun Liu
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Heat Insulation ◽  
High Humidity ◽  
Underground Engineering ◽  
New Approach ◽  
Foamed Concrete ◽  
Insulation Performance

Aimed at improving the waterproofing property of foamed concrete, a heat-insulating and waterproofing composite applied in underground engineering was prepared by using cementitious capillary crystalline waterproofing material and foamed concrete. The properties of foamed concrete and composite such as compressive strength, water absorption and thermal conductivity were tested and contrasted, and the compounding reaction mechanism was analyzed. The results show that, compared with foamed concrete, the water absorption of composite has been significantly reduced while the heat-insulating property of foamed concrete is maintained and the overall waterproofing and heat-insulation performance has been significantly improved. A new approach solving underground heat-harm such as high temperature and high humidity is provided.

scholarly journals Compressive Strength and Dimensional Stability of Palm Oil Empty Fruit Bunch Fibre Reinforced Foamed Concrete

2018 ◽  
Vol 65 ◽  
pp. 02001 ◽  
Author(s):  
Siong Kang Lim ◽  
Hock Yong Tiong ◽  
Kai Siong Woon
Keyword(s):  
Compressive Strength ◽  
Palm Oil ◽  
Dimensional Stability ◽  
Performance Index ◽  
Weather Condition ◽  
Drying Shrinkage ◽  
Cement Matrix ◽  
Strength Performance ◽  
Curing Conditions ◽  
Foamed Concrete

Rapid drying shrinkage is an important factor in causing cracks of concrete. This research was aimed at studying the effects of Palm Oil Empty Fruited Bunch (POEFB) fibre on the drying shrinkage behaviour and compressive strength of foamed concrete (FC) under two different curing conditions. The adopted curing conditions were air curing and tropical natural weather curing. Two volume fractions of POEFB fibre were used, which were 0.25% and 0.50% based on dry mix weight with 1-2 cm in length. The dimensional stability of the control specimen and POEFB fibre reinforced FCs was obtained by cumulating the measured linear shrinkage or expansion due to different curing conditions. The results from the two different specimens were compared. The results showed that specimens reinforced with POEFB fibre and cured under tropical natural weather condition attained lesser variations of dimensional stability and higher 90-day strength performance index than the reference mix without POEFB fibre. This improvement was attributed to the ability of POEFB fibre to bridge the cement matrix, and irregular wetting process under tropical natural weather curing condition had enabled more production of Calcium Silicate Hydrate gels that gradually blocked the penetration of water into the specimens and increased the compressive strength. It is observed that 11.43% and 4.46% of improvement in 90-day strength performance index were obtained in natural weather cured 0.5% of POEFB fibre reinforced specimen, with corresponded to the reference mix and 0.25% of POEFB fibre reinforced specimens, respectively.

scholarly journals Drying Shrinkage of Mortar Incorporating High Volume Oil Palm Biomass Waste

2018 ◽  
Vol 34 ◽  
pp. 01008
Author(s):  
Nor Hasanah Abdul Shukor Lim ◽  
Mostafa Samadi ◽  
Abdul Rahman Mohd. Sam ◽  
Nur Hafizah Abd Khalid ◽  
Noor Nabilah Sarbini ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Palm Oil ◽  
Oil Palm ◽  
Palm Kernel ◽  
Drying Shrinkage ◽  
Biomass Waste ◽  
Palm Oil Fuel Ash ◽  
Fuel Ash ◽  
Oil Palm Biomass ◽  
Oil Fuel

This paper studies the drying shrinkage of mortar incorporating oil palm biomass waste including Palm Oil Fuel Ash, Oil Palm Kernel Shell and Oil Palm Fibre. Nano size of palm oil fuel ash was used up to 80 % as cement replacement by weight. The ash has been treated to improve the physical and chemical properties of mortar. The mass ratio of sand to blended ashes was 3:1. The test was carried out using 25 × 25 × 160 mm prism for drying shrinkage tests and 70 × 70 ×70 mm for compressive strength test. The results show that the shrinkage value of biomass mortar is reduced by 31% compared with OPC mortar thus, showing better performance in restraining deformation of the mortar while the compressive strength increased by 24% compared with OPC mortar at later age. The study gives a better understanding of how the biomass waste affect on mortar compressive strength and drying shrinkage behaviour. Overall, the oil palm biomass waste can be used to produce a better performance mortar at later age in terms of compressive strength and drying shrinkage.

Sign in / Sign up

Export Citation Format

Share Document