Effect of Particle Size on Cadmium Removal by Banana Peels

2015 ◽  
Vol 72 (4) ◽  
Author(s):  
Mohd Ismid Mohd Said ◽  
Shaikhah Sabri ◽  
Shamila Azman
Keyword(s):  
Particle Size ◽  
Metal Removal ◽  
Low Cost ◽  
Polluted Water ◽  
Banana Peel ◽  
Cadmium Removal ◽  
Musa Balbisiana ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Adsorption Equilibrium Data

Contamination of metals in aquatic environment is a worldwide problem because of its toxicity and capability to accumulate in biological chain, as well as persistence in the natural environment. Therefore various expensive technologies have been applied to treat metal-polluted water. In Malaysia there are abundance of banana species available which could provide cheap, low cost and environmental friendly bio-materials. Preliminary study was conducted on two species of banana i.e. Musa balbisiana (Nipah) and Musa acuminata (Kapas). The banana peels were washed, dried and grounded into various range of particle sizes (0.20–1.18 mm). The ability of the adsorbents were determined by agitation of 1.0 g banana peel and 100 ml of cadmium standard solution at the concentration of 100 mg/L. Musa balbisiana showed the highest removal of cadmium at 89.58% from the initial concentration compared to Musa acuminate with the particle size of 0.30-0.60 mm. Adsorption equilibrium data are well described by Langmuir isotherm model. The result also shows that different species have different capabilities to adsorb metal. Hence, their potential as bio-adsorbent could be further be examined for metal removal from wastewater.

scholarly journals Competitive Adsorption of Cadmium(II) and Mercury(II) Ions from Aqueous Solutions by Activated Carbon from Xanthoceras sorbifolia Bunge Hull

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Xiaotao Zhang ◽  
Yinan Hao ◽  
Ximing Wang ◽  
Zhangjing Chen ◽  
Chun Li
Keyword(s):  
Activated Carbon ◽  
High Efficiency ◽  
Metal Removal ◽  
Chemical Interaction ◽  
Low Cost ◽  
Heavy Metal Removal ◽  
Metal System ◽  
Experimental Conditions ◽  
Equilibrium Data ◽  
Adsorption Equilibrium Data

This paper presents low-cost and recyclable activated carbon (XLAC) derived from Xanthoceras sorbifolia Bunge hull for high-efficiency adsorption of Cd(II) and Hg(II) ions in industrial wastewater. XLAC was prepared through H3PO4 activation and was characterized using N2 adsorption-desorption, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDX), and Fourier transform infrared (FTIR) spectroscopy. In single-metal-system adsorption experiments, the maximum adsorption capacities for Cd(II) and Hg(II) obtained under different experimental conditions were 388.7 and 235.6 mg·g−1, respectively. All adsorption equilibrium data fit perfectly with the Langmuir isotherm model. In a binary metal system, competitive studies demonstrated that the presence of Cd(II) significantly decreased the adsorption of Hg(II), but the adsorption of Cd(II) showed a little change in the presence of Hg(II). In addition, XLAC can be regenerated with a 0.01 mol·L−1 HNO3 solution and reused at least four times. The FTIR spectra revealed that a chemical interaction occurs between functional groups containing lone electron pairs in XLAC and metal ions. Overall, these results suggest that XLAC may be suitable as an adsorbent for heavy metal removal from wastewater streams.

scholarly journals Adsorption of Methylene Blue by Low-Cost Biochar Derived from Elephant Dung

2021 ◽  
pp. 34-44
Author(s):  
Yanasinee Suma ◽  
Nittaya Pasukphun ◽  
Numfon Eaktasang
Keyword(s):  
Methylene Blue ◽  
Dynamic Models ◽  
Adsorption Process ◽  
Low Cost ◽  
Homogeneous Surface ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Adsorption Equilibrium Data ◽  
Mb Adsorption ◽  
Elephant Dung

Elephant dung biochar (ED350) prepared by controlled heating at 350 ºC was used to adsorb methylene blue (MB) in an aqueous solution. The effects of adsorption time, pH, adsorbent dosage, and initial MB concentration were examined. Kinetic, isotherm, and thermo-dynamic models were then further analyzed to determine the adsorption. The results show that ED350 was found to be efficient within 180 min. The optimum pH of MB adsorption was 11. The Langmuir isotherm model was found to be the most suitable fit for the adsorption equilibrium data, with ED350 having a homogeneous surface. The calculated equilibrium parameter (RL) values were greater than zero and less than one, indicating a favorable adsorption process and that ED350 was an efficient adsorbent for MB removal. The kinetics of MB adsorption onto ED350 obeys the pseudo-second-order model. The results of thermo-dynamic data consideration reveal that the adsorption process is spontaneous and exothermic in nature. This finding suggests that ED350 may prove to be an efficient low-cost adsorbent of MB from wastewater.

scholarly journals Effective Poly (Cyclotriphosphazene-Co-4,4′-Sulfonyldiphenol)@rGO Sheets for Tetracycline Adsorption: Fabrication, Characterization, Adsorption Kinetics and Thermodynamics

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1540
Author(s):  
Muhammad Ahmad ◽  
Tehseen Nawaz ◽  
Mohammad Mujahid Alam ◽  
Yasir Abbas ◽  
Shafqat Ali ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
High Adsorption ◽  
Clean Environment ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
High Adsorption Capacity ◽  
Adsorption Equilibrium Data

The development of excellent drug adsorbents and clarifying the interaction mechanisms between adsorbents and adsorbates are greatly desired for a clean environment. Herein, we report that a reduced graphene oxide modified sheeted polyphosphazene (rGO/poly (cyclotriphosphazene-co-4,4′-sulfonyldiphenol)) defined as PZS on rGO was used to remove the tetracycline (TC) drug from an aqueous solution. Compared to PZS microspheres, the adsorption capacity of sheeted PZS@rGO exhibited a high adsorption capacity of 496 mg/g. The adsorption equilibrium data well obeyed the Langmuir isotherm model, and the kinetics isotherm was fitted to the pseudo-second-order model. Thermodynamic analysis showed that the adsorption of TC was an exothermic, spontaneous process. Furthermore, we highlighted the importance of the surface modification of PZS by the introduction of rGO, which tremendously increased the surface area necessary for high adsorption. Along with high surface area, electrostatic attractions, H-bonding, π-π stacking and Lewis acid-base interactions were involved in the high adsorption capacity of PZS@rGO. Furthermore, we also proposed the mechanism of TC adsorption via PZS@rGO.

scholarly journals Adsorption capability of brewed tea waste in waters containing toxic lead(II), cadmium (II), nickel (II), and zinc(II) heavy metal ions

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Hakan Çelebi ◽  
Gülden Gök ◽  
Oğuzhan Gök
Keyword(s):  
Heavy Metals ◽  
Adsorption Process ◽  
Low Cost ◽  
Adsorption Capacities ◽  
Tea Waste ◽  
Optimum Ph ◽  
Effects Of Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Adsorption Capability

Abstract Recently, the search for low-cost eco-friendly adsorbents has become one of the main objectives of researchers. The aim of this study was to test the removal of four heavy metals, namely lead (Pb), zinc (Zn), nickel (Ni) and cadmium (Cd), from a simulated watery solution using brewed tea waste as a potentially suitable adsorbent. The effects of pH levels (2.0–6.0), adsorbent amount (0.1–5.0 g), contact times (1–150 min.) were examined throughout the adsorption process. The results of the experiments showed that the heavy metals elimination yields had an inverse relationship with pH and a linear relationship between the other parameters. The optimum pH for the removal of the heavy metals was between 4.0 and 5.0 in the case of the brewed tea waste. Equilibrium times of 2, 10, 30 and 5 min were required for the adsorption of Pb, Zn, Ni, Cd onto Camellia sinensis, respectively. Based on the results of this study it can be said that brewed tea waste has a high potential to remove heavy metals from aqueous solutions. The maximum adsorption capacities were calculated as 1.197, 1.457, 1.163 and 2.468 mg/g, for Pb, Zn, Ni and Cd, respectively, by fitting the equilibrium data to the Langmuir isotherm model.

Potential of Agricultural Waste Material (Ananas cosmos) as Biosorbent for Heavy Metal Removal in Polluted Water

2020 ◽  
Vol 1010 ◽  
pp. 489-494
Author(s):  
Abdul Hafidz Yusoff ◽  
Rosmawani Mohammad ◽  
Mardawani Mohamad ◽  
Ahmad Ziad Sulaiman ◽  
Nurul Akmar Che Zaudin ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Adsorption Capacity ◽  
Metal Removal ◽  
Low Cost ◽  
Agricultural Waste ◽  
Heavy Metal Removal ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Pineapple Peel

Conventional methods to remove heavy metals from polluted water are expensive and not environmentally friendly. Therefore, this study was carried out to investigate the potential of agricultural waste such as pineapple peel (Ananas Cosmos) as low-cost absorbent to remove heavy metals from synthetic polluted water. The results showed that Cd, Cr and Pb were effectively removed by the biosorbent at 12g of pineapple peels in 100 mL solution. The optimum contact time for maximum adsorption was found to be 90 minutes, while the optimum pH for the heavy metal’s adsorption was 9. It was demonstrated that with the increase of adsorbent dosage, the percent of heavy metals removal was also increased due to the increasing adsorption capacity of the adsorbent. In addition, Langmuir model show maximum adsorption capacity of Cd is 1.91 mg/g. As conclusions, our findings show that pineapple peel has potential to remove heavy metal from polluted water.

scholarly journals Studies on Removal of Cr (VI) from Aqueous Solutions Using Powder of Mosambi Fruit Peelings (PMFP) As a Low Cost Sorbent

2012 ◽  
Vol 9 (3) ◽  
pp. 1389-1399 ◽  
Author(s):  
R. Hema Krishna ◽  
A. V. V. S. Swamy
Keyword(s):  
Particle Size ◽  
Aqueous Solutions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Batch Tests ◽  
Freundlich Adsorption Isotherm ◽  
Equilibrium Data ◽  
Agitation Time

The powder of mosambi fruit peelings (PMFP) was used as an adsorbent for the removal of heavy metal like Cr (VI) from aqueous solutions was studied using batch tests. The influence of physico-chemical key parameters such as the initial metal ion concentration, pH, agitation time, adsorbent dosage, and the particle size of adsorbent has been considered in batch tests. Sorbent ability to adsorb Cr (VI) ions was examined and the mechanism involved in the process investigated. The optimum results were determined at an initial metal ion concentration was 10 mg/lit, pH=2, agitation time – 60 min, an adsorbent dose (150 mg/50 ml) and the particle size (0.6 mm). The % adsorption, Langmuir constants [Q0=7.51(mg/g) and b=1.69(mg/lit)] Freundlich constant(Kf=2.94), Lagergren rate constants (Kad(min-1)=5.75 x 10-2) for [Cr(VI)] 10 mg/lit were determined for the adsorption system as a function of sorbate concentration. The equilibrium data obtained were tested using Langmuir, Freundlich adsorption isotherm models, and the kinetic data obtained were fitted to pseudo first order model.

scholarly journals Adsorption of Nickel and Chromium Ions by Amine-Functionalized Silica Aerogel

2018 ◽  
Vol 156 ◽  
pp. 03014
Author(s):  
Sudarat Sertsing ◽  
Thanaphat Chukeaw ◽  
Sitthiphong Pengpanich ◽  
Bawornpong Pornchuti
Keyword(s):  
Silica Aerogel ◽  
Solution Concentration ◽  
Functionalized Silica ◽  
Solution Ph ◽  
Chromium Ions ◽  
Amine Functionalized ◽  
Adsorption Capacities ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Adsorption Equilibrium Data

In this study, silica aerogel was synthesized by drying at atmospheric pressure and modified further with aminopropyl triethoxysilane (APTES). The amine-functionalized silica aerogel was investigated as an adsorbent for removal of nickel and chromium ions. The effect of contact time, solution pH, and initial solution concentration were studied. The equilibrium was achieved within 60 min. The optimum pH was found to be 4. Adsorption equilibrium data were agreed fairly well with Langmuir isotherm model. Adsorption capacities for nickel and chromium ions were found to be 40.32 mg/g and 46.08 mg/g, respectively.

Removal of Pb(II) by adsorption onto Chinese walnut shell activated carbon

2015 ◽  
Vol 72 (6) ◽  
pp. 983-989 ◽  
Author(s):  
Zheng-ji Yi ◽  
Jun Yao ◽  
Yun-fei Kuang ◽  
Hui-lun Chen ◽  
Fei Wang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Walnut Shell ◽  
Maximum Adsorption Capacity ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Chinese Walnut ◽  
Maximum Removal

The excessive discharge of Pb(II) into the environment has increasingly aroused great concern. Adsorption is considered as the most effective method for heavy metal removal. Chinese walnut shell activated carbon (CWSAC) was used as an adsorbent for the removal of Pb(II) from aqueous solution. Batch experiments were conducted by varying contact time, temperature, pH, adsorbent dose and initial Pb(II) concentration. Adsorption equilibrium was established within 150 min. Although temperature effect was insignificant, the Pb(II) adsorption was strongly pH dependent and the maximum removal was observed at pH 5.5. The Pb(II) removal efficiency increased with increasing CWSAC dosage up to 2.0 g/L and reached a maximum of 94.12%. Langmuir and Freundlich adsorption isotherms were employed to fit the adsorption data. The results suggested that the equilibrium data could be well described by the Langmuir isotherm model, with a maximum adsorption capacity of 81.96 mg/g. Adsorption kinetics data were fitted by pseudo-first- and pseudo-second-order models. The result indicated that the pseudo-first-order model best describes the adsorption kinetic data. In summary, CWSAC could be a promising material for the removal of Pb(II) from wastewater.

scholarly journals Kush - A Potential Biosorbent in the removal of Cd (II) and Zn (II) from aqueous solution

2012 ◽  
Vol 27 ◽  
pp. 107-114
Author(s):  
Jagjit Kour ◽  
P. L. Homagai ◽  
M. R. Pokherel ◽  
K. N. Ghimire
Keyword(s):  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Waste Streams ◽  
Adsorption Capacities ◽  
Optimum Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The industrial discharge of heavy metals into waters' course is one of the major pollution problems affecting water quality. Therefore, they must be removed prior to their discharge into waste streams. An efficient and low-cost bioadsorbent has been investigated from Desmostachya bipinnata (Kush) by charring with concentrated sulphuric acid and functionalized with dimethylamine.It was characterised by SEM, FTIR and elemental analysis. The effect of pH, initial concentration and contact time of the metal solution was monitered by batch method. The maximum adsorption capacities were determined for Cd and Zn at their optimum pH 6. The equilibrium data were analysed using Langmuir and Freundlich isotherm models. Langmuir isotherm model fitted well and the rate of adsorption followed the pseudo second order kinetic equation.DOI: http://dx.doi.org/10.3126/jncs.v27i1.6669 J. Nepal Chem. Soc., Vol. 27, 2011 107-114  

scholarly journals (3-Aminopropyl) Triethoxysilane (APTES) Functionalized Magnetic Nanosilica Graphene Oxide (MGO) Nanocomposite for the Comparative Adsorption of the Heavy Metal (Pb(II), Cd(II) and Ni(II)) ions from Aqueous Solution

2021 ◽  
Author(s):  
C Donga ◽  
S Mishra ◽  
A Aziz ◽  
L Ndlovu ◽  
A Kuvarega ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Graphene Oxide ◽  
Metal Ion ◽  
Ion Concentration ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Magnetic Graphene Oxide ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Adsorption Equilibrium Data

Abstract (3-aminopropyl) triethoxysilane (APTES) modified magnetic graphene oxide was synthesized and applied in the adsorption of three heavy metals, Pb(II), Cd(II) and Ni(II) from aqueous solution. An approach to prepare magnetic GO was adopted by using (3-aminopropyl) triethoxysilane (APTES) as a functionalizing agent on magnetic nanosilica coupled with GO to form the Fe3O4@SiO2-NH2/GO nanocomposite. FT-IR, XRD, BET, UV, VSM, SAXS, SEM and TEM were used to characterize the synthesized nanoadsorbents. Batch adsorption studies were conducted to investigate the effect of solution pH, initial metal ion concentration, adsorbent dosage and contact time. The maximum equilibrium time was found to be 30 min for Pb(II), Cd(II) and 60 min for Ni(II). The kinetics studies showed that the adsorption of Pb(II), Cd(II) and Ni(II) onto Fe3O4@SiO2-NH2/GO followed the pseudo-second-order kinetics. All the adsorption equilibrium data were well fitted to Langmuir isotherm model and maximum monolayer adsorption capacity for Pb(II), Cd(II) and Ni(II) were 13.46, 18.58 and 13.52 mgg-1, respectively. The Fe3O4@SiO2-NH2/GO adsorbents were reused for at least 7 cycles without the leaching of mineral core, showing the enhanced stability and potential application of Fe3O4@SiO2-NH2/GO adsorbents in water/wastewater treatment.

Sign in / Sign up

Export Citation Format

Share Document