Effect of Velocity Variation at High Swirl on Axial Flow Development inside a Can Combustor

2014 ◽  
Vol 71 (2) ◽  
Author(s):  
Mohamad Shaiful Ashrul Ishak ◽  
Mohammad Nazri Mohd. Jaafar
Keyword(s):  
Flow Field ◽  
Combustion Chamber ◽  
Reverse Flow ◽  
Flow Behavior ◽  
Axial Flow ◽  
Internal Flow ◽  
Velocity Variation ◽  
Recirculation Region ◽  
Injection Velocity ◽  
Mixing Enhancement

The main purpose of this paper is to study the internal flow effect of varying the inlet velocities inside a combustor. The flow field inside the combustor is controlled by the liner shape and size, wall side holes shape, size and arrangement (primary, secondary and dilution holes), and primary air swirler configuration. Air swirler adds sufficient swirling to the inlet flow to generate central recirculation region (CRZ) which is necessary for flame stability and fuel air mixing enhancement. Therefore, designing an appropriate air swirler is a challenge to produce stable, efficient and low emission combustion with low pressure losses. Four various injection velocities from 30m/s to 60m/s with radial vanes angle of 50 degree were used in this analysis to show velocity effect on the internal flow field. The flow behavior was investigated numerically using CFD solver Ansys 14.0. This study has provided the characteristic insight into the flow pattern inside the combustion chamber. Results show that the swirling action is augmented with the increase in the injection velocity, which leads to increase in core reverse flow, thus enhancing mixing of fuel and air in the combustion chamber.

Numerical Analysis on the CO-NO Formation Production near Burner Throat in Swirling Flow Combustion System

2014 ◽  
Vol 69 (2) ◽  
Author(s):  
Mohamad Shaiful Ashrul Ishak ◽  
Mohammad Nazri Mohd Jaafar
Keyword(s):  
Swirling Flow ◽  
Reverse Flow ◽  
Flow Behavior ◽  
Recirculation Region ◽  
Mixing Enhancement ◽  
Ansys Fluent ◽  
Pressure Losses ◽  
No Formation ◽  
Swirl Angle ◽  
Air Mixing

The main purpose of this paper is to study the Computational Fluid Dynamics (CFD) prediction on CO-NO formation production inside the combustor close to burner throat while varying the swirl angle of the radial swirler. Air swirler adds sufficient swirling to the inlet flow to generate central recirculation region (CRZ) which is necessary for flame stability and fuel air mixing enhancement. Therefore, designing an appropriate air swirler is a challenge to produce stable, efficient and low emission combustion with low pressure losses. A liquid fuel burner system with different radial air swirler with 280 mm inside diameter combustor of 1000 mm length has been investigated. Analysis were carried out using four different radial air swirlers having 30°, 40°, 50° and 60° vane angles. The flow behavior was investigated numerically using CFD solver Ansys Fluent. This study has provided characteristic insight into the formation and production of CO and pollutant NO inside the combustion chamber. Results show that the swirling action is augmented with the increase in the swirl angle, which leads to increase in the center core reverse flow, therefore reducing the CO and pollutant NO formation. The outcome of this work will help in finding out the optimum swirling angle which will lead to less emission.  

Numerical simulation of three-dimensional airflow in a novel dual-feed rotor spinning box

2016 ◽  
Vol 88 (3) ◽  
pp. 237-253 ◽  
Author(s):  
Nicholus Tayari Akankwasa ◽  
Huiting Lin ◽  
Yuze Zhang ◽  
Jun Wang
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Three Dimensional ◽  
Internal Flow ◽  
Velocity Variation ◽  
Positive Pressure ◽  
Three Dimensional Model ◽  
Air Velocity ◽  
Rotor Spinning ◽  
Pressure Profiles

In order to regulate turbulence strength and determine airflow characteristics in a new dual-feed rotor spinning unit, the internal flow field is investigated. A computational fluid dynamics technique is employed to numerically study the three-dimensional model of the internal airflow in the new design. The effects of air velocity variation on turbulence strength, negative pressure, Re, and wall pressure distribution are investigated based on simulation data and previous studies. The results show that the turbulence strength and Re increased with increase in inlet air velocity. Pressure profiles inside the rotor varied significantly with positive pressure observed at the channel exits. Minimal inlet velocity maintains the flow field in the rotor interior below 100 m/s, which gives the ideal turbulence required to minimize yarn quality deterioration. The dual-feed rotor spinning unit showed more orderly streamline patterns with fewer vortices compared to the conventional one. The numerical simulation can provide insights on airflow studies and some guidelines for future prototyping and experiments to further improve the new design.

Design, Evaluation and Performance Analysis of Staged Low Emission Combustors

2012 ◽  
Author(s):  
Gajanana B. Hegde ◽  
Bhupendra Khandelwal ◽  
Vishal Sethi ◽  
Riti Singh
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Design Methodology ◽  
Reverse Flow ◽  
Axial Flow ◽  
Design Procedure ◽  
Extensive Study ◽  
Theoretical Design ◽  
Low Emission ◽  
And Performance

The most uncertain and challenging part in the design of a gas turbine has long been the combustion chamber. There has been large number of experimentations in industries and universities alike to better understand the dynamic and complex processes that occur inside a combustion chamber. This study concentrates on gas turbine combustors as a whole, and formulates a theoretical design procedure for staged combustors in particular. Not much of literatures available currently in public domain provide intensive study on designing staged combustors. The work covers an extensive study of design methods applied in conventional combustor designs, which includes the reverse flow combustor and the axial flow annular combustors. The knowledge acquired from this study is then applied to develop a theoretical design methodology for double staged (radial and axial) low emission annular combustors. Additionally a model combustor is designed for each type; radial and axial staging using the developed methodology. A prediction of the performance for the model combustors is executed. The main conclusion is that the dimensions of model combustors obtained from the developed design methodology are within the feasibility limits. The comparison between the radially staged and the axially staged combustor has yielded the predicted results such as lower NOx prediction for the latter and shorter combustor length for the former. The NOx emission result of the new combustor models are found to be in the range of 50–60ppm. However the predicted NOx results are only very crude and need further detailed study.

An Investigation of Axial Pump Backflow and a Method for its Control

1988 ◽  
Author(s):  
M. Abramian ◽  
J. H. G. Howard ◽  
P. Hermann
Keyword(s):  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Recirculation Zone ◽  
Reverse Flow ◽  
Axial Flow ◽  
Leading Edge ◽  
Low Flow ◽  
Flow Conditions ◽  
Axial Pump ◽  
Swirl Velocity

The flow field within an axial flow inducer pump near the blade leading edge was explored by laser-Doppler velocimetry to extend the previous studies of the recirculation zone which is observed at low flow rates. Although a considerable region of upstream reverse flow and swirl was observed, the recirculation zone within the impeller was of limited axial extent and was confined to the pressure side of the passage. In an attempt to reduce the flow reversal, a series of perforated disks were placed in front of the inducer. The optimum disk geometry produced minor changes in the pump performance. LDV measurements of the flow field ahead and behind the disk showed considerable reduction of the swirl velocity under reverse flow conditions, with the observed upstream swirl opposite to the inducer rotation.

Mechanism of affecting the performance and internal flow field of an axial flow subsonic compressor with self-recirculation casing treatment

2020 ◽  
pp. 095441002094267
Author(s):  
Hao G Zhang ◽  
Fei Y Dong ◽  
Wei Wang ◽  
Wu L Chu ◽  
Song Yan
Keyword(s):  
Flow Field ◽  
Axial Flow ◽  
Internal Flow ◽  
Leading Edge ◽  
Tip Clearance ◽  
Stall Margin ◽  
Casing Treatment ◽  
Leakage Flows ◽  
Blade Tip ◽  
Compressor Performance

This investigation aims to understand the mechanisms of affecting the axial flow compressor performance and internal flow field with the application of self-recirculation casing treatment. Besides, the potentiality of further enhancing the compressor performance and stability by optimizing the geometric structure of self-recirculation casing treatment is discussed in detail. The results show that self-recirculation casing treatment generates about 7.06, 7.89% stall margin improvements in the experiment and full-annulus unsteady calculation, respectively. Moreover, the compressor total pressure and isentropic efficiency are improved among most of operating points, and the experimental and calculated compressor peak efficiencies are increased by 0.7% and 0.6%, respectively. The comparisons between baseline shroud and self-recirculation casing treatment show that the flow conditions of the compressor rotor inlet upstream are improved well with self-recirculation casing treatment, and the degree of the pressure enhancement in the blade top passage for self-recirculation casing treatment is higher than that for baseline. Further, self-recirculation casing treatment can restrain the leading edge-spilled flows made by the blade tip clearance leakage flows and weaken the blade tip passage blockage. Hence, the flow loss near the rotor top passage is reduced after the application of self-recirculation casing treatment. The rotor performance and stability for self-recirculation casing treatment are greater than those for baseline. The flow-field analyses also indicate that the adverse effects caused by the clearance leakage flows of the blades tip rear are greater than those made by the clearance leakage flows of the blades leading edge. When one injecting part of self-recirculation casing treatment is aligned with the inlet of one blade tip passage, the flow-field quality in the passage is not the best among all the passages between two adjacent injecting parts of self-recirculation casing treatment. Further, the flow-field analyses also indicate that the effect of the relative position between the blade and self-recirculation casing treatment on the flows in the self-recirculation casing treatment may be ignored during the optimization of the recirculating loop configuration.

Numerical Analysis of Effect of Preheat and Swirl of Inlet Air on Temperature Profile in Canister Burner

2015 ◽  
Vol 72 (4) ◽  
Author(s):  
Mohamad Shaiful Ashrul Ishak ◽  
Mohammad Nazri Mohd. Jaafar ◽  
Wan Zaidi Wan Omar
Keyword(s):  
Temperature Distribution ◽  
Temperature Profile ◽  
Hot Spot ◽  
Flow Behavior ◽  
Recirculation Region ◽  
Mixing Enhancement ◽  
Ansys Fluent ◽  
Pressure Losses ◽  
Swirl Angle ◽  
Air Mixing

The main purpose of this paper is to study the Computational Fluid Dynamics (CFD) prediction on temperature distribution inside the canister burner with inlet air pre-heating of 100K and 250K while varying the swirl angle of the radial swirler. Air swirler adds sufficient swirling to the inlet flow to generate central recirculation region (CRZ) which is necessary for flame stability and fuel air mixing enhancement. Therefore, designing an appropriate air swirler is a challenge to produce stable, efficient and low emission combustion with low pressure losses. A liquid fuel burner system with different radial air swirler with 280 mm inside diameter combustor of 1000 mm length has been investigated. Analysis were carried out using four different radial air swirlers having 30°, 40°, 50° and 60° vane angles. The flow behavior was investigated numerically using CFD solver Ansys Fluent. This study has provided characteristic insight into the distribution of temperature inside the combustion chamber. Results show that with the inlet air preheat before the combustion, the temperature distribution inside the canister would stabilize early into the chamber with higher swirl number (SN) compared without inlet air preheat. As for the inlet air preheat, the main effects are the resulting temperatures in the canister are higher, but there is a smaller hot-spot in the flame. This means that the temperature profile in the chamber is well distributed.

C16 Effect of Rotor-Stator Gap on Internal Flow Field in an Axial Flow Compressor near Stall

2008 ◽  
Vol 2008.61 (0) ◽  
pp. 85-86
Author(s):  
Noritaka NAKAMURA ◽  
Takahiro MORIKAWA ◽  
Yasuhiro SHIBAMOTO ◽  
Ken-ichiro IWAKIRI ◽  
Satoshi GUNJISHIMA ◽  
...  
Keyword(s):  
Flow Field ◽  
Axial Flow ◽  
Internal Flow ◽  
Axial Flow Compressor ◽  
Flow Compressor

A CFD Method Study on the Resistance Performance of the Axial Flow Cyclone Separator

2017 ◽  
Author(s):  
Yigang Luan ◽  
Lianfeng Yang ◽  
Tao Sun
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Axial Flow ◽  
Internal Flow ◽  
Operating Pressure ◽  
Cyclone Separator ◽  
Axial Flow Cyclone ◽  
Flow Field Characteristics ◽  
Numerical Simulation Methods ◽  
Resistance Performance

Axial flow cyclone separator with guide blade has been widely used, due to its low resistance, huge gas processing and small volume. Although its structure is simple, three-dimension strong rotating turbulent flow forms which involves many complex interactions such as dual-phase separation, adsorption and electrostatic interference. This paper is focused on studying the resistance performance of the axial flow cyclone separator. Numerical simulation methods are carried out to acquire the internal flow field characteristics under different operating pressure and temperature conditions. The result shows that the pressure drop decreases under the same operating pressure, as the operating temperature increases. When the operating temperature is the same, the higher operating pressure enhances the value of the pressure drop. Velocity distribution, pressure contours and turbulent viscosity contours have been presented, to analyze the characteristics of the internal airflow, so as to help optimize the design. Experiments are intended to verify the results of numerical simulation and explore the internal flow field of the cyclone separator further. The cyclone separator has 8 rotary blades which are split into 8 parts, namely one blade is 45° in the tangential direction. 0° and 22.5° are chosen in the experiment. The dimensionless pressure distribution is shown. A comparison of the CFD results and the experimental results is made to prove that the numerical simulation methods are correct and accurate. The curve of the numerical simulation results is very close to that of the experimental results with the similar trend. It is concluded that the methods can predict the internal flow field characteristics of the axial flow cyclone separator.

scholarly journals Numerical investigations on effect of wear-ring clearance on performance of a submersible well pump

2017 ◽  
Vol 9 (7) ◽  
pp. 168781401770415 ◽  
Author(s):  
Weidong Shi ◽  
Xiongfa Gao ◽  
Qihua Zhang ◽  
Desheng Zhang ◽  
Daoxing Ye
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Reverse Flow ◽  
Internal Flow ◽  
Experimental Results ◽  
Ring Size ◽  
Numerical Investigations ◽  
Calculation Results

A typical submersible well pump was investigated in this article. The whole flow field of submersible well pump was numerically simulated by computational fluid dynamics software. The influence of clearance of wear-rings on the external characteristic and internal flow field was analyzed through comparing the calculation results with experimental results. The result of the numerical simulation shows that changing clearance of front wear-ring has a greater impact on pump performances than changing clearance of back wear-ring, and the head and efficiency of pump decrease with the increase in the size of clearance. Especially when the size of clearance is larger than 0.5 mm, decreasing becomes more obvious. When the front and back wear-ring size of the clearance comes to 1.0 mm, the efficiency decreases from the highest point of 75.31% to 65.44% at rated flow, and the head of pump decreases about 3.5 m. When the size of clearance is 0.2 mm, reverse-flow will appear in the front shroud cavity of the impeller, and leakage from back wear-ring through the balance hole into the impeller, which has a little influence on the flow field of the impeller inlet.

The Effect of Inlet Air Preheat on CO and NO Production in the Combustion of Diesel in Canister Burner

2014 ◽  
Vol 71 (2) ◽  
Author(s):  
Mohamad Shaiful Ashrul Ishak ◽  
Mohammad Nazri Mohd Jaafar ◽  
Wan Zaidi Wan Omar
Keyword(s):  
Fuel Injection ◽  
Flow Behavior ◽  
Recirculation Region ◽  
Mixing Enhancement ◽  
No Production ◽  
Injection Point ◽  
Ansys Fluent ◽  
Pressure Losses ◽  
Swirl Angle ◽  
Air Mixing

The main purpose of this paper is to study the Computational Fluid Dynamics (CFD) prediction on the formation of carbon monoxide and oxide of nitrogen (CO-NO) inside the canister burner with inlet air pre-heating of 100 K and 250 K while varying the swirl angle of the radial swirler. Air swirler adds sufficient swirling to the inlet flow to generate central recirculation region (CRZ) which is necessary for flame stability and fuel air mixing enhancement. Therefore, designing an appropriate air swirler is a challenge to produce stable, efficient and low emission combustion with low pressure losses. A liquid fuel burner system with different radial air swirler with 280 mm inside diameter combustor of 1000 mm length was investigated. Analyses were carried out using four different radial air swirlers having 30°, 40°, 50° and 60° vane angles. The flow behavior was also investigated numerically using CFD solver Ansys Fluent. Overall results show that inlet air preheat quickens the completion of combustion such that the CO and NO production stabilized at a point nearer to fuel injection point, and reduced the CO and NO concentrations due to the combustion. 

Sign in / Sign up

Export Citation Format

Share Document