Enhanced Absorption of Microwaves Within Cylindrical Holes in Teflon Film

2010 ◽  
Vol 57 (10) ◽  
pp. 2517-2524 ◽  
Author(s):  
Stanislav I Alekseev ◽  
Evgeny E Fesenko ◽  
Marvin C Ziskin
2000 ◽  
Vol 629 ◽  
Author(s):  
Jean-Loup Masson ◽  
Peter F. Green

ABSTRACTResearchers have shown that thin, nonwetting, liquid homopolymer films dewet substrates, forming patterns that reflect fluctuations in the local film thickness. These patterns have been shown to be either discrete cylindrical holes or bicontinuous “spinodal-like” patterns. In this paper we show the existence of a new morphology. During the early stage of dewetting, discrete highly asymmetric holes appear spontaneously throughout the film. The nucleation rate of these holes is faster than their growth rate. The morphology of the late stage of evolution, after 18 days, is characterized by a bicontinuous pattern, distinct form conventional spinodal dewetting patterns. This morphology has been observed for a range of film thicknesses between 7.5 and 21nm. The structural evolution of this intermediate morphology is discussed.


2015 ◽  
Vol 3 (2) ◽  
pp. 15-27
Author(s):  
Ahmed A. Imram ◽  
Humam K. Jalghef ◽  
Falah F. Hatem

     The effect of introducing ramp with a cylindrical slot hole on the film cooling effectiveness has been investigated experimentally and numerically. The film cooling effectiveness measurements are obtained experimentally. A test study was performed at a single mainstream with Reynolds number 76600 at three different coolant to mainstream blowing ratios 1.5, 2, and 3. Numerical simulation is introduced to primarily estimate the best ramp configurations and to predict the behavior of the transport phenomena in the region linked closely to the interaction between the coolant air injection and the hot air mainstram flow. The results showed that using ramps with trench cylindrical holes would enhanced the overall film cooling effectiveness by 83.33% compared with baseline model at blowing ratio of 1.5, also  the best overall flim cooling effectevness was obtained at blowing ratio of 2 while it is reduced at blowing ratio of 3.


Author(s):  
Thomas E. Dyson ◽  
Dave G. Bogard ◽  
Justin D. Piggush ◽  
Atul Kohli

Overall effectiveness, φ, for a simulated turbine blade leading edge was experimentally measured using a model constructed with a relatively high conductivity material selected so that the Biot number of the model matched engine conditions. The model incorporated three rows of cylindrical holes with the center row positioned on the stagnation line. Internally the model used an impingement cooling configuration. Overall effectiveness was measured for pitch variation from 7.6d to 9.6d for blowing ratios ranging from 0.5 to 3.0, and angle of attack from −7.7° to +7.7°. Performance was evaluated for operation with a constant overall mass flow rate of coolant. Consequently when increasing the pitch, the blowing ratio was increased proportionally. The increased blowing ratio resulted in increased impingement cooling internally and increased convective cooling through the holes. The increased internal and convective cooling compensated, to a degree, for the decreased coolant coverage with increased pitch. Performance was evaluated in terms of laterally averaged φ, but also in terms of the minimum φ. The minimum φ evaluation revealed localized hot spots which are arguably more critical to turbine blade durability than the laterally averaged results. For small increases in pitch there was negligible decrease in performance.


Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2953
Author(s):  
Hao Jiang ◽  
Caiwen Ma ◽  
Ming Li ◽  
Zhiliang Cao

Ultrafast laser drilling has been proven to effectively reduce the heat-affected zone (HAZ) of carbon fiber-reinforced polymer (CFRP) composites. However, previous research mainly focused on the effects of picosecond laser parameters on CFRP drilling. Compared with a picosecond laser, a femtosecond laser can achieve higher quality CFRP drilling due to its smaller pulse width, but there are few studies on the effects of femtosecond laser parameters on CFRP drilling. Moreover, the cross-sectional taper of CFRP produced by laser drilling is very large. This paper introduces the use of the femtosecond laser to drill cylindrical holes in CFRP. The effect of laser power, rotational speed of the laser, and number of spiral passes on HAZ and ablation depth in circular laser drilling and spiral laser drilling mode was studied, respectively. It also analyzed the forming process of the drilling depth in the spiral drilling mode and studied the influence of laser energy and drilling feed depth on the holes’ diameters and the taper. The experimental results show that the cylindrical hole of CFRP with a depth-to-diameter ratio of about 3:1 (taper < 0.32∘, HAZ < 10 m) was obtained by using femtosecond laser and a spiral drilling apparatus.


Nanoscale ◽  
2014 ◽  
Vol 6 (15) ◽  
pp. 9148-9156 ◽  
Author(s):  
Joyashish Debgupta ◽  
Ramireddy Devarapalli ◽  
Shakeelur Rahman ◽  
Manjusha V. Shelke ◽  
Vijayamohanan K. Pillai

Heterojunction (type II) of self standing, vertically aligned CdSe NTs (n-type) with electrodeposited Cu2O (p-type) exhibits excellent photoresponse, resulting from enhanced absorption of light and faster transport of photogenerated charge carriers by CdSe NTs.


2021 ◽  
Vol 23 (5) ◽  
Author(s):  
Piotr Dubinski ◽  
Katarzyna Czarzasta ◽  
Agnieszka Cudnoch-Jedrzejewska

Abstract Purpose of Review Based on the available data, it can be assumed that microbiota is an integral part of the human body. The most heavily colonized area of the human body is the gut, with bacterial accumulation ranging from 101–103 cells/g in the upper intestine to 1011–1012 cells/g in the colon. However, colonization of the gut is not the same throughout, as it was shown that there are differences between the composition of the microbiota in the intestine lumen and in the proximity of the mucus layer. Recent Findings Gut microbiota gradient can be differentially regulated by factors such as obesity and chronic stress. In particular, a high fat diet influences the gut microbial composition. It was also found that chronic stress may cause the development of obesity and thus change the organization of the intestinal barrier. Recent research has shown the significant effect of intestinal microflora on cardiovascular function. Enhanced absorption of bacterial fragments, such as lipopolysaccharide (LPS), promotes the onset of “metabolic endotoxemia,” which could activate toll-like receptors, which mediates an inflammatory response and in severe cases could cause cardiovascular diseases. It is presumed that the intestinal microbiota, and especially its metabolites (LPS and trimethylamine N-oxide (TMAO)), may play an important role in the pathogenesis of arterial hypertension, atherosclerosis, and heart failure. Summary This review focuses on how gut microbiota can change the morphological and functional activity of the cardiovascular system in the course of obesity and in conditions of chronic stress.


2021 ◽  
Vol 23 ◽  
pp. 104072
Author(s):  
Wei Cui ◽  
Lingqiao Li ◽  
Weiwei Xue ◽  
Hui Xu ◽  
Zhihui He ◽  
...  
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document