On low-cost space mapping optimization of antenna structures

2016 ◽  
Author(s):  
Slawomir Koziel ◽  
Qingsha S. Cheng ◽  
Qingfeng Zhang
Keyword(s):  
Low Cost ◽  
Space Mapping

scholarly journals Modelling Wireless Propagation for Indoor Localization

2016 ◽  
Author(s):  
Shweta Jain ◽  
Christian Barona ◽  
Nicholas Madamopoulos
Keyword(s):  
Ray Tracing ◽  
Indoor Localization ◽  
Low Cost ◽  
Path Loss ◽  
Signal Propagation ◽  
Space Mapping ◽  
Indoor Space ◽  
Tracing Techniques ◽  
Vector Sum ◽  
Indoor Spaces

This paper presents a ray-tracing technique to model the multi-path fading effect in indoor spaces. Random set P of points on all surfaces inside a given hypothetical indoor space are chosen. Each pi ∈ P is considered to be a point from which the transmitted signal reflects just before reaching the receiver. The received signal is the vector sum of various reflections that arrive at the receiver. The received signal strength (RSS) is then computed from the signal envelope. This technique provides RSS statistics that are similar to the models of signal propagation developed after extensive measurements in multi-path environments. In addition, this technique captures the spatial correlation of signal impairment. For example, path loss computed with this technique shows that co-moving receivers experience correlated signal fades while those moving in different spaces see un-correlated fading. The technique presented here is a low cost, first principle approach to simulate channel impairments due to multi-path effect and interference. It benefits any wireless simulation study that needs the signal-space mapping and context such as indoor localization. This randomized ray-tracing technique does not compete with or replace other, more accurate ray-tracing techniques that use either brute force or geometric optics to obtain site-specific signal-to-space mapping.  

scholarly journals EXPERIMENTAL ASSESSMENT OF 3D NARROW SPACE MAPPING TECHNOLOGIES

2020 ◽  
Vol XLIII-B2-2020 ◽  
pp. 149-156
Author(s):  
G. Piniotis ◽  
S. Soile ◽  
F. Bourexis ◽  
M. Tsakiri ◽  
C. Ioannidis
Keyword(s):  
Low Cost ◽  
Point Clouds ◽  
3D Models ◽  
Space Mapping ◽  
Experimental Assessment ◽  
High Importance ◽  
3D Point Clouds ◽  
Narrow Space ◽  
Mapping Result ◽  
Mapping Systems

Abstract. Narrow space surveying and mapping is of high importance for many applications, with the demand for digital 3D models in a low-cost and relatively fast way growing rapidly. This paper examines SLAM-based and image-based mapping systems for indoor mapping and focuses on the comparison of the 3D point clouds acquired from two commercial mapping systems, Leica BLK2GO and Matterport Pro2 3D (MC250). Issues that are addressed include the effect of the mapping trajectory on the produced mapping result, and the amount of mapping propagation error in narrow space surveying. The two systems are experimentally compared against both an ideal geometric target facility and in an example environment of a narrow corridor. Finally, results are given with derived metrics that can be possibly extended to several real applications.

Decomposition of the metastable beta titanium alloy Ti-15-3

1983 ◽  
Vol 41 ◽  
pp. 264-265
Author(s):  
Y. L. Chen ◽  
S. Fujlshiro
Keyword(s):  
Low Cost ◽  
High Strength ◽  
Alpha Phase ◽  
Thick Sheet ◽  
Omega Phase ◽  
Beta Titanium Alloy ◽  
Beta Titanium ◽  
Beta Matrix ◽  
Metastable Beta ◽  
Very High

Metastable beta titanium alloys have been known to have numerous advantages such as cold formability, high strength, good fracture resistance, deep hardenability, and cost effectiveness. Very high strength is obtainable by precipitation of the hexagonal alpha phase in a bcc beta matrix in these alloys. Precipitation hardening in the metastable beta alloys may also result from the formation of transition phases such as omega phase. Ti-15-3 (Ti-15V- 3Cr-3Al-3Sn) has been developed recently by TIMET and USAF for low cost sheet metal applications. The purpose of the present study was to examine the aging characteristics in this alloy.The composition of the as-received material is: 14.7 V, 3.14 Cr, 3.05 Al, 2.26 Sn, and 0.145 Fe. The beta transus temperature as determined by optical metallographic method was about 770°C. Specimen coupons were prepared from a mill-annealed 1.2 mm thick sheet, and solution treated at 827°C for 2 hr in argon, then water quenched. Aging was also done in argon at temperatures ranging from 316 to 616°C for various times.

Chromic Acid Etching of Polyethylene

1973 ◽  
Vol 31 ◽  
pp. 72-73
Author(s):  
J. D. Muzzy ◽  
R. D. Hester ◽  
J. L. Hubbard
Keyword(s):  
Chromic Acid ◽  
Low Cost ◽  
Acid Etching ◽  
Crystalline Morphology ◽  
Bulk Specimen ◽  
Morphological Studies ◽  
Perfect Form ◽  
Molecular Length ◽  
Lamellar Texture ◽  
Cost Studies

Polyethylene is one of the most important plastics produced today because of its good physical properties, ease of fabrication and low cost. Studies to improve the properties of polyethylene are leading to an understanding of its crystalline morphology. Polyethylene crystallized by evaporation from dilute solutions consists of thin crystals called lamellae. The polyethylene molecules are parallel to the thickness of the lamellae and are folded since the thickness of the lamellae is much less than the molecular length. This lamellar texture persists in less perfect form in polyethylene crystallized from the melt.Morphological studies of melt crystallized polyethylene have been limited due to the difficulty of isolating the microstructure from the bulk specimen without destroying or deforming it.

Glass Knife Geometry as Seen by the SEM

1971 ◽  
Vol 29 ◽  
pp. 454-455
Author(s):  
J. Temple Black
Keyword(s):  
Low Cost ◽  
Amorphous Material ◽  
Stress Concentrations ◽  
Basic Tool ◽  
Tool Materials ◽  
Optical Inspection ◽  
Surface Flaws ◽  
Slip Planes ◽  
Glass Knife ◽  
Diamond Knife

In ultramicrotomy, the two basic tool materials are glass and diamond. Glass because of its low cost and ease of manufacture of the knife itself is still widely used despite the superiority of diamond knives in many applications. Both kinds of knives produce plastic deformation in the microtomed section due to the nature of the cutting process and microscopic chips in the edge of the knife. Because glass has no well defined slip planes in its structure (it's an amorphous material), it is very strong and essentially never fails in compression. However, surface flaws produce stress concentrations which reduce the strength of glass to 10,000 to 20,000 psi from its theoretical or flaw free values of 1 to 2 million psi. While the microchips in the edge of the glass or diamond knife are generally too small to be observed in the SEM, the second common type of defect can be identified. This is the striations (also termed the check marks or feathers) which are always present over the entire edge of a glass knife regardless of whether or not they are visable under optical inspection. These steps in the cutting edge can be observed in the SEM by proper preparation of carefully broken knives and orientation of the knife, with respect to the scanning beam.

Spectraplot: A PC-based spectrum translation and display program

1988 ◽  
Vol 46 ◽  
pp. 918-919
Author(s):  
H. O. Colijn
Keyword(s):  
Low Cost ◽  
Transfer Program ◽  
File Transfer ◽  
Transfer Data ◽  
Error Checking ◽  
Data Files ◽  
The University

Many labs today wish to transfer data between their EDS systems and their existing PCs and minicomputers. Our lab has implemented SpectraPlot, a low- cost PC-based system to allow offline examination and plotting of spectra. We adopted this system in order to make more efficient use of our microscopes and EDS consoles, to provide hardcopy output for an older EDS system, and to allow students to access their data after leaving the university.As shown in Fig. 1, we have three EDS systems (one of which is located in another building) which can store data on 8 inch RT-11 floppy disks. We transfer data from these systems to a DEC MINC computer using “SneakerNet”, which consists of putting on a pair of sneakers and running down the hall. We then use the Hermit file transfer program to download the data files with error checking from the MINC to the PC.

Transmission Electron Microscopy of oriented Co84Cr14Ta2 thin films for longitudinal magnetic recording

1991 ◽  
Vol 49 ◽  
pp. 756-757
Author(s):  
T. P. Nolan
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Cost ◽  
Low Noise ◽  
Information Storage ◽  
High Coercivity ◽  
Magnetic Alloy ◽  
Magnetic Media ◽  
Transmission Electron

Thin film magnetic media are being used as low cost, high density forms of information storage. The development of this technology requires the study, at the sub-micron level, of morphological, crystallographic, and magnetic properties, throughout the depth of the deposited films. As the microstructure becomes increasingly fine, widi grain sizes approaching 100Å, the unique characterization capabilities of transmission electron microscopy (TEM) have become indispensable to the analysis of such thin film magnetic media.Films were deposited at 225°C, on two NiP plated Al substrates, one polished, and one circumferentially textured with a mean roughness of 55Å. Three layers, a 750Å chromium underlayer, a 600Å layer of magnetic alloy of composition Co84Cr14Ta2, and a 300Å amorphous carbon overcoat were then sputter deposited using a dc magnetron system at a power of 1kW, in a chamber evacuated below 10-6 torr and filled to 12μm Ar pressure. The textured medium is presently used in industry owing to its high coercivity, Hc, and relatively low noise. One important feature is that the coercivity in the circumferential read/write direction is significandy higher than that in the radial direction.

Sign in / Sign up

Export Citation Format

Share Document