p-Type MOSFET Contact Resistance Improvement by Conformal Plasma Doping and Nanosecond Laser Annealing

2019 ◽  
Vol 40 (2) ◽  
pp. 307-309 ◽  
Author(s):  
C. I. Li ◽  
N. Breil ◽  
T. Y. Wen ◽  
S. Y. Liu ◽  
M. S. Hsieh ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Laser Annealing ◽  
Nanosecond Laser ◽  
Plasma Doping ◽  
P Type ◽  
Resistance Improvement

Contact Resistance Improvement for Advanced Logic by Integration of Epi, Implant and Anneal Innovations

MRS Advances ◽  
2019 ◽  
Vol 4 (48) ◽  
pp. 2559-2576
Author(s):  
Fareen Adeni Khaja
Keyword(s):  
Contact Resistance ◽  
Nanosecond Laser ◽  
Dopant Activation ◽  
Cmos Scaling ◽  
Dominant Component ◽  
Plasma Doping ◽  
Recent Trends ◽  
Metastable Alloys ◽  
Laser Anneal

ABSTRACTAs advanced CMOS scaling with FinFETs continues beyond the 10/7nm nodes, contact resistance (Rc) remains a dominant component affecting device performance. The FinFET Source/Drain (S/D) contact area has become smaller with fin pitch scaling, resulting in drastically increased Rc. To achieve higher drive currents and fully realize the performance gain from FinFET architectural changes, it is critical to continue to reduce contact resistivity (ρc) < 1.0x10-9 Ω.cm2 for both NMOS and PMOS. In this paper, we review the recent trends for ρc reduction for advanced CMOS devices and discuss approaches that have demonstrated reduction in ρc, such as in-situ heavily doped epitaxial films for S/D, advanced ion implantation and laser anneals. The implant techniques include pre-amorphization implants (PAI), dopant boosting implants, cryogenic (-100°C) implants for damage engineering and plasma doping (PLAD) for conformal doping of high aspect ratio (HAR) contacts. With such high levels of doping from epi and implants, advanced laser anneals are key for epitaxial regrowth and formation of metastable alloys for dopant supersaturation or segregation in top layers. Millisecond laser anneal (MSA) improves dopant activation and nanosecond laser anneal (NLA) permits superactivation, and both have become key enablers for ρc reduction. This paper also reviews two alternative contact approaches: dual silicide scheme and wrap-around contact (WAC), as potential pathways to further reduce Rc for advanced CMOS nodes.

Improvement of the Specific Contact Resistance on P-Type 4H-SiC by Using a Highly P-Typed Doped 4H-SiC Layer Selectively Grown by VLS Transport

2014 ◽  
Vol 806 ◽  
pp. 57-60
Author(s):  
Nicolas Thierry-Jebali ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Mihai Lazar ◽  
Gabriel Ferro ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Schottky Barrier Height ◽  
Annealing Temperature ◽  
Process Condition ◽  
Specific Contact Resistance ◽  
High Doping Level ◽  
Annealing Temperatures ◽  
Specific Contact ◽  
P Type

This work reports on the improvement of ohmic contacts made on heavily p-type doped 4H-SiC epitaxial layer selectively grown by Vapor-Liquid-Solid (VLS) transport. Even before any annealing process, the contact is ohmic. This behavior can be explained by the high doping level of the VLS layer (Al concentration > 1020 cm-3) as characterized by SIMS profiling. Upon variation of annealing temperatures, a minimum value of the Specific Contact Resistance (SCR) down to 1.3x10-6 Ω.cm2 has been obtained for both 500 °C and 800 °C annealing temperature. However, a large variation of the SCR was observed for a same process condition. This variation is mainly attributed to a variation of the Schottky Barrier Height.

Photoluminescence of Pulsed Ruby Laser Annealed Crystalline and Ion Implanted GaAs

1981 ◽  
Vol 4 ◽  
Author(s):  
Douglas H. Lowndes ◽  
Bernard J. Feldman
Keyword(s):  
Radiative Recombination ◽  
Laser Annealing ◽  
Laser Energy ◽  
Pulsed Laser ◽  
High Dose ◽  
Pulsed Laser Annealing ◽  
Recombination Centers ◽  
Pl Intensity ◽  
P Type ◽  
Ion Implanted

ABSTRACTIn an effort to understand the origin of defects earlier found to be present in p–n junctions formed by pulsed laser annealing (PLA) of ion implanted (II) semiconducting GaAs, photoluminescence (PL) studies have been carried out. PL spectra have been obtained at 4K, 77K and 300K, for both n–and p–type GaAs, for laser energy densities 0 ≤ El ≤ 0.6 J/cm2. It is found that PLA of crystalline (c−) GaAs alters the PL spectrum and decreases the PL intensity, corresponding to an increase in density of non-radiative recombination centers with increasing El. The variation of PL intensity with El is found to be different for n– and p–type material. No PL is observed from high dose (1 or 5×1015 ions/cm2 ) Sior Zn-implanted GaAs, either before or after laser annealing. The results suggest that the ion implantation step is primarily responsible for formation of defects associated with the loss of radiative recombination, with pulsed annealing contributing only secondarily.

Heat Transfer and Phase Transformations in Laser Annealing of Thin a-Si Films

2001 ◽  
Author(s):  
Seung-Jae Moon ◽  
Minghong Lee ◽  
Costas P. Grigoropoulos
Keyword(s):  
Laser Annealing ◽  
Thermal Emission ◽  
Electrical Conductance ◽  
Nanosecond Laser ◽  
Solidification Velocity ◽  
Emission Measurement ◽  
Excimer Laser Annealing ◽  
In Situ Experiments ◽  
Si Films

Abstract The liquid-solid interface motion and the temperature history of thin Si films during excimer laser annealing are observed by in situ experiments combining time-resolved (∼lns) thermal emission measurements, optical reflectance and transmittance at near-IR wavelengths and electrical conductance measurements. The spontaneous nucleation temperature in the supercooled liquid melt is studied from the thermal emission measurement A new double laser recrystallization technique using a temporally modulated CW Ar+ laser in conjunction with a superposed nanosecond laser pulse produces lateral grain growth at the irradiated spot. The laser melting process is numerically simulated. High-resolution laser flash photography enabled in-situ direct visualization of the resolidification process. The images reveal lateral solidification velocity of about 10 m/s.

Ohmic Contacts to p-Type InGaAs/InP with a Graded Bandgap Heterobarrier

1993 ◽  
Vol 318 ◽  
Author(s):  
Patrick W. Leech ◽  
Geoffrey K. Reeves
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Rutherford Backscattering Spectrometry ◽  
Specific Contact Resistance ◽  
Superlattice Structure ◽  
Specific Contact ◽  
P Type ◽  
Metal Layers ◽  
Anneal Temperature ◽  
Graded Bandgap

ABSTRACTOhmic contacts to p-type InP with an In0.47Ga0.53As buffer layer and an interposed superlattice of 50 Å In0.47Ga0.53As/ 50 Å InP have been investigated. Initial studies of contacts to In0.47Ga0.53As/ InP without the superlattice structure have shown that Pd/Zn/Pd/Au metallization produced a lower specific contact resistance (pc = 1.1 × 10−4 Ω cm2) than Pd/Ge/Au, and over a wider range of anneal temperature than Au/Zn/Au. The incorporation of the superlattice in the p-In0.47Ga0.53As/ InP structure resulted in Pd/Zn/Pd/Au contacts with pc of 3.2 × 10−5 Ω cm2 as-deposited and 7.5 × 10−6 Ω.cm2 after a 500 °C anneal. The presence of Pd/Zn in the metallization was shown as important in reducing pc. Significant intermixing of the metal layers and In0.47Ga0.53As occured at ≥ 350 °C, as revealed by Rutherford backscattering spectrometry.

scholarly journals Исследование формирования омических контактов Au/Mo/Ti с пониженным сопротивлением к эпитаксиальным слоям алмаза p-типа

2019 ◽  
Vol 89 (12) ◽  
pp. 1923
Author(s):  
М.Н. Дроздов ◽  
Е.В. Демидов ◽  
Ю.Н. Дроздов ◽  
С.А. Краев ◽  
В.И. Шашкин ◽  
...  
Keyword(s):  
Titanium Carbide ◽  
Contact Resistance ◽  
Ohmic Contacts ◽  
Contact Region ◽  
Effective Diffusion ◽  
Protective Properties ◽  
High Adhesion ◽  
Heavy Doping ◽  
P Type

The formation of ohmic Au/Mo/Ti contacts to epitaxial p-type diamond films is studied. The effect of annealing on the electrical and structural properties of contacts has been investigated. It was shown that during rapid thermal annealing, the outer layer of gold protects the contact system from oxidation up to a temperature of 850°C, unlike the simplified Au/Ti system, which is more common in modern works. In Au/Ti structures without a Mo layer after high-temperature annealing, effective diffusion of titanium into the gold layer occurs, which reduces its protective properties and accelerates the diffusion of oxygen to the boundary with the diamond. Oxidation of the Ti/C contact region blocks the formation of a conductive layer of titanium carbide with high adhesion at the border with diamond. The role of various factors in reducing the contact resistance is compared: annealing for the formation of titanium carbide, heavy doping of diamond with boron atoms, and crystalline perfection of epitaxial diamond substrates. For doped epitaxial films grown on single-sector quality substrates, non-annealed ohmic contacts with a record contact resistance of 4•10<-7> Ω•cm<2> were obtained.

Sign in / Sign up

Export Citation Format

Share Document