A Comparison between Predicted and Experimental Results for Swaged Fin Heat Sinks

2006 ◽  
Author(s):  
J.A. Visser ◽  
A. Zaghlol ◽  
F.D. Conradie
Keyword(s):  
Experimental Results ◽  
Heat Sinks

Finned Metal Foam Heat Sinks for Electronics Cooling in Forced Convection

2002 ◽  
Vol 124 (3) ◽  
pp. 155-163 ◽  
Author(s):  
A. Bhattacharya ◽  
R. L. Mahajan
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Forced Convection ◽  
Metal Foam ◽  
Experimental Results ◽  
Heat Sinks ◽  
The Heat Transfer Coefficient

In this paper, we present recent experimental results on forced convective heat transfer in novel finned metal foam heat sinks. Experiments were conducted on aluminum foams of 90 percent porosity and pore size corresponding to 5 PPI (200 PPM) and 20 PPI (800 PPM) with one, two, four and six fins, where PPI (PPM) stands for pores per inch (pores per meter) and is a measure of the pore density of the porous medium. All of these heat sinks were fabricated in-house. The forced convection results show that heat transfer is significantly enhanced when fins are incorporated in metal foam. The heat transfer coefficient increases with increase in the number of fins until adding more fins retards heat transfer due to interference of thermal boundary layers. For the 20 PPI samples, this maximum was reached for four fins. For the 5 PPI heat sinks, the trends were found to be similar to those for the 20 PPI heat sinks. However, due to larger pore sizes, the pressure drop encountered is much lower at a particular air velocity. As a result, for a given pressure drop, the heat transfer coefficient is higher compared to the 20 PPI heat sink. For example, at a Δp of 105 Pa, the heat transfer coefficients were found to be 1169W/m2-K and 995W/m2-K for the 5 PPI and 20 PPI 4-finned heat sinks, respectively. The finned metal foam heat sinks outperform the longitudinal finned and normal metal foam heat sinks by a factor between 1.5 and 2, respectively. Finally, an analytical expression is formulated based on flow through an open channel and incorporating the effects of thermal dispersion and interfacial heat transfer between the solid and fluid phases of the porous medium. The agreement of the proposed relation with the experimental results is promising.

Buoyancy-Induced Convection in Metal Foam and Finned Metal Foam Heat Sinks©

2000 ◽  
Author(s):  
A. Bhattacharya ◽  
Roop L. Mahajan
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Metal Foam ◽  
Metal Foams ◽  
Experimental Results ◽  
Heat Sinks ◽  
Normal Metal ◽  
Optimum Number

Abstract In this paper, we present our recent experimental results on buoyancy induced convection in metal foams of different pore densities (corresponding to 5, 10, 20 and 40 pores per inch) and porosities (0.89–0.96). The results show that compared to a hot surface facing up, the heat transfer coefficients in these heat sinks are 5 to 6 times higher. However, when compared to commercially available heat sinks of similar dimensions, the enhancement is found to be marginal. The experimental results also show that for a given pore size, the heat transfer rate increases with porosity suggesting the dominant role played by conduction in enhancing heat transfer. On the other hand, if the porosity is held constant, the heat transfer rate is found to be lower at higher pore densities. This can be attributed to the higher permeability with the larger pores, which allows higher entrainment of air through the porous medium. An empirical correlation, developed for the estimation of Nusselt number in terms of Rayleigh and Darcy numbers, is found to be in good agreement with the experimental data with a maximum error of 10%. We also report our results on novel finned metal foam heat sinks© in natural convection. Experiments were conducted on aluminum foams of 90% porosity with 5 and 20 PPI (pores per inch) with one, two, and four aluminum fins inserted in the foam. All these heat sinks were fabricated in-house. The results show that the finned metal foam heat sinks© are superior in thermal performance compared to the normal metal foam and conventional finned heat sinks. The heat transfer increases with increase in the number of fins. However, the relative enhancement is found to decrease with each additional fin. The indication is that there exists an optimum number of fins beyond which the enhancement in heat transfer due to increased surface area is offset by the retarding effect of overlapping thermal boundary layers. Similar to normal metal foams, the 5 PPI samples are found to give higher values of the heat transfer coefficient compared to the 20 PPI samples due to higher permeability of the porous medium. Future work is planned to arrive at the optimal heat sink configuration for even larger enhancement in heat transfer.

A Novel Micropump for Electronics Cooling

2004 ◽  
Author(s):  
Vishal Singhal ◽  
Suresh V. Garimella
Keyword(s):  
Numerical Model ◽  
Charge Transport ◽  
Flow Rate ◽  
Electronics Cooling ◽  
Experimental Results ◽  
Heat Sinks ◽  
Flow Rates ◽  
Microchannel Heat Sinks ◽  
Combined Action

A novel micropump design for electronics cooling applications capable of integration into microchannel heat sinks is presented. The pumping action is due to the combined action of Coulomb forces due to induction electrohydrodynamics (EHD) and a vibrating diaphragm with nozzle-diffuser elements for flow rectification. A comprehensive numerical model of the micropump accounting for transient charge transport and vibrating diaphragm deformation is developed. Each component of the model is validated by comparing to analytical, numerical or experimental results from the literature. It is shown that the flow rate achieved by the micropump with combined action of EHD and vibrating diaphragm can be higher than the sum of flow rates achieved from the action of the EHD and the vibrating diaphragm, independent of each other.

scholarly journals Study on Thermoelectric Cooler Driven by Solar Energy in Medan City

2018 ◽  
Vol 6 (2) ◽  
pp. 317-327
Author(s):  
Tulus Burhanuddin Sitorus ◽  
Zulkifli Lubis ◽  
Farida Ariani ◽  
Ferry Sembiring
Keyword(s):  
Solar Energy ◽  
Low Temperatures ◽  
Cooling System ◽  
Thermoelectric Module ◽  
Weather Conditions ◽  
Experimental Results ◽  
Heat Sinks ◽  
Peltier Effect ◽  
Thermoelectric Cooler ◽  
Cold Side

The primary purpose of this study is to investigate the performance of thermoelectric cooler driven by solar energy in Medan city, Indonesia. This cooler able to use in a remote area where electricity is still not available. The cooler could be used to store beverage that must be stored at low temperatures to maintain the freshness such as drink cup. The solar thermoelectric cooler is based on the principles of a thermoelectric module or Peltier effect to create a hot side and a cold side. The cold side of the thermoelectric module is utilized for cooling purposes to the cooling space. The heat from the hot side of the module is rejected to ambient surroundings by using heat sinks and fans. The solar thermoelectric cooler was experimentally tested for the cooling purpose. Experimental results showed that the solar thermoelectric cooler could reduce the temperature of the drink cup from 26oC to 15oC in approximately 40 min. The maximum COP of the cooling system during the experiment was calculated and found to be about 0.356. The effect of weather conditions on the COP value was about 85.90%.

Experiments and Modeling of the Heat Transfer of In-Line Square Pin Fin Heat Sinks With Top By-Pass Flow

2002 ◽  
Author(s):  
M. Baris Dogruoz ◽  
Mario Urdaneta ◽  
Alfonso Ortega
Keyword(s):  
Heat Transfer ◽  
Experimental Results ◽  
Heat Sinks ◽  
Transfer Coefficients ◽  
Clearance Ratio ◽  
One Dimensional ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Approach Velocity ◽  
Good Agreement

This paper presents experimental results on the heat transfer characteristics of in-line square pin fin heat sinks with and without top by-pass. A self-consistent set of aluminum heat sinks were utilized, where the pin height was varied from 12.5 mm to 22.5 mm, the pin pitch was varied from 3.4 mm to 5.8 mm and the base dimensions were kept fixed at 25 × 25 mm. The overall base to ambient thermal resistance was measured as a function of Reynolds number and bypass height. Experimental results were then compared with predictions based on a simple one-dimensional “two-branch by-pass model”. Comparisons were made with the data using heat transfer coefficients available in the literature for infinitely long tube bundles. It was shown that there is a good agreement between the temperature predictions based on the model and the experimental data at high approach velocities for tall heat sinks, however the discrepancy between the computations and experiments increases as the approach velocity and heat sink height decrease. The validated model was used to identify optimum pin spacing as a function of clearance ratio.

scholarly journals Water cooled micro-hole cellular structure as a heat dissipation media: An experimental and numerical study

2020 ◽  
Vol 24 (2 Part A) ◽  
pp. 683-692 ◽  
Author(s):  
Hussain Tariq ◽  
Ahmad Shoukat ◽  
Muhammad Anwar ◽  
Asif Israr ◽  
Hafiz Ali
Keyword(s):  
Flow Rate ◽  
Cellular Structure ◽  
Heat Dissipation ◽  
Numerical Study ◽  
Volumetric Flow Rate ◽  
Experimental Results ◽  
Heat Sinks ◽  
Base Temperature ◽  
Micro Hole ◽  
Alumina Nanofluid

Thermal performance of micro-hole cellular structure using water as a cool?ing fluid was investigated through CFD and then numerical results were validated with the experimental results. The minimum base temperature for the micro-hole cellular structure was found to be 29.7?C and 32.3?C numerically and experimentally, respectively, with volumetric flow rate of 0.000034 m3/s (2 Lpm) at a heating power of 345 W. Numerical values of the base temperature are in close agreement with experimental results with an error of 8.75%. Previously, the base temperatures of heat sinks using alumina nanofluid with 1% of volumetric concentration and water with volumetric flow rate of 0.000017 m3/s (1 Lpm) have been reported to be 43.9?C and 40.5?C, respectively.

Thermal conductivity from hierarchical heat sinks using carbon nanotubes and graphene nanosheets

Nanoscale ◽  
2015 ◽  
Vol 7 (44) ◽  
pp. 18663-18670 ◽  
Author(s):  
Chien-Te Hsieh ◽  
Cheng-En Lee ◽  
Yu-Fu Chen ◽  
Jeng-Kuei Chang ◽  
Hsi-sheng Teng
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Thermal Management ◽  
Graphene Nanosheets ◽  
Consumer Electronics ◽  
Experimental Results ◽  
Heat Sinks ◽  
Empirical Equations ◽  
The Relationship

The relationship between thermal conductivity (k) and electrical conductivity (ε) values was well described by two empirical equations. The experimental results were obtained within the 323–373 K range, suitably complementing the thermal management of chips for consumer electronics.

Metal Foam and Finned Metal Foam Heat Sinks for Electronics Cooling in Buoyancy-Induced Convection

2005 ◽  
Vol 128 (3) ◽  
pp. 259-266 ◽  
Author(s):  
A. Bhattacharya ◽  
R. L. Mahajan
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Metal Foam ◽  
Metal Foams ◽  
Experimental Results ◽  
Heat Sinks ◽  
Normal Metal ◽  
Optimum Number

In this paper, we present our recent experimental results on buoyancy-induced convection in aluminum metal foams of different pore densities [corresponding to 5, 10, 20, and 40 pores per in. (PPI)] and porosities (0.89–0.96). The results show that compared to a heated surface, the heat transfer coefficients in these heat sinks are five to six times higher. However, when compared to commercially available heat sinks of similar dimensions, the enhancement is found to be marginal. The experimental results also show that for a given pore size, the heat transfer rate increases with porosity, suggesting the dominant role played by conduction in enhancing heat transfer. On the other hand, if the porosity is held constant, the heat transfer rate is found to be lower at higher pore densities. This can be attributed to the higher permeability with the larger pores, which allows higher entrainment of air through the porous medium. New empirical correlations are proposed for the estimation of Nusselt number in terms of Rayleigh and Darcy numbers. We also report our results on novel finned metal foam heat sinks in natural convection. Experiments were conducted on aluminum foams of 90% porosity with 5 and 20 PPI with one, two, and four aluminum fins inserted in the foam. All of these heat sinks were fabricated in-house. The results show that the finned metal foam heat sinks are superior in thermal performance compared to the normal metal foam and conventional finned heat sinks. The heat transfer increases with an increase in the number of fins. However, the relative enhancement is found to decrease with each additional fin. The indication is that there exists an optimum number of fins beyond which the enhancement in heat transfer, due to increased surface area, is offset by the retarding effect of overlapping thermal boundary layers. Similar to normal metal foams, the 5 PPI samples are found to give higher values of h compared to the 20 PPI samples due to higher permeability of the porous medium. Future work is planned to arrive at the optimal heat sink configuration for even larger enhancement in heat transfer.

Diagnostics of Gold Laser Plasmas

1988 ◽  
Vol 102 ◽  
pp. 357-360
Author(s):  
J.C. Gauthier ◽  
J.P. Geindre ◽  
P. Monier ◽  
C. Chenais-Popovics ◽  
N. Tragin ◽  
...  
Keyword(s):  
Experimental Results ◽  
Pure Gold ◽  
Electronic Temperature ◽  
X Ray ◽  
Laser Plasmas ◽  
Collisional Radiative Model ◽  
Radiative Model

AbstractIn order to achieve a nickel-like X ray laser scheme we need a tool to determine the parameters which characterise the high-Z plasma. The aim of this work is to study gold laser plasmas and to compare experimental results to a collisional-radiative model which describes nickel-like ions. The electronic temperature and density are measured by the emission of an aluminium tracer. They are compared to the predictions of the nickel-like model for pure gold. The results show that the density and temperature can be estimated in a pure gold plasma.

Observation of Phase Contrast Images in STEM and CTEM Modes by Using 100 kV Field Emission Electron Gun

1974 ◽  
Vol 32 ◽  
pp. 390-391
Author(s):  
Y. Harada ◽  
T. Goto ◽  
H. Koike ◽  
T. Someya
Keyword(s):  
Field Emission ◽  
Phase Contrast ◽  
Image Formation ◽  
Fresnel Diffraction ◽  
Experimental Results ◽  
Electron Gun ◽  
Scanning Microscopy ◽  
Emission Electron ◽  
Lattice Images

Since phase contrasts of STEM images, that is, Fresnel diffraction fringes or lattice images, manifest themselves in field emission scanning microscopy, the mechanism for image formation in the STEM mode has been investigated and compared with that in CTEM mode, resulting in the theory of reciprocity. It reveals that contrast in STEM images exhibits the same properties as contrast in CTEM images. However, it appears that the validity of the reciprocity theory, especially on the details of phase contrast, has not yet been fully proven by the experiments. In this work, we shall investigate the phase contrast images obtained in both the STEM and CTEM modes of a field emission microscope (100kV), and evaluate the validity of the reciprocity theory by comparing the experimental results.

Sign in / Sign up

Export Citation Format

Share Document