A Low Noise Analog Front-end Design with an N-path Filter for Dry EEG Recording

2018 ◽  
Author(s):  
Takumi Deguchi ◽  
Ryoya Tanaka ◽  
Shohei Kawazoe ◽  
Ryuto Fukuoka ◽  
Nobuhiko Nakano
Keyword(s):  
Low Noise ◽  
Front End ◽  
Analog Front End

scholarly journals 14.85 µW Analog Front-End for Photoplethysmography Acquisition with 142-dBΩ Gain and 64.2-pArms Noise

Sensors ◽  
2019 ◽  
Vol 19 (3) ◽  
pp. 512
Author(s):  
Binghui Lin ◽  
Mohamed Atef ◽  
Guoxing Wang
Keyword(s):  
Dynamic Range ◽  
Automatic Gain Control ◽  
Gain Control ◽  
Low Noise ◽  
Total Power ◽  
Cmos Process ◽  
Control Block ◽  
Silicon Area ◽  
Front End ◽  
Analog Front End

A low-power, high-gain, and low-noise analog front-end (AFE) for wearable photoplethysmography (PPG) acquisition systems is designed and fabricated in a 0.35 μm CMOS process. A high transimpedance gain of 142 dBΩ and a low input-referred noise of only 64.2 pArms was achieved. A Sub-Hz filter was integrated using a pseudo resistor, resulting in a small silicon area. To mitigate the saturation problem caused by background light (BGL), a BGL cancellation loop and a new simple automatic gain control block are used to enhance the dynamic range and improve the linearity of the AFE. The measurement results show that a DC photocurrent component up-to-10 μA can be rejected and the PPG output swing can reach 1.42 Vpp at THD < 1%. The chip consumes a total power of 14.85 μW using a single 3.3-V power supply. In this work, the small area and efficiently integrated blocks were used to implement the PPG AFE and the silicon area is minimized to 0.8 mm × 0.8 mm.

scholarly journals A 0.5 V 68 nW ECG Monitoring Analog Front-End for Arrhythmia Diagnosis

2018 ◽  
Vol 8 (3) ◽  
pp. 27 ◽  
Author(s):  
Avish Kosari ◽  
Jacob Breiholz ◽  
NingXi Liu ◽  
Benton Calhoun ◽  
David Wentzloff
Keyword(s):  
Low Power ◽  
Power Efficiency ◽  
Low Noise ◽  
Signal Acquisition ◽  
Cmos Process ◽  
Ecg Signal ◽  
Ecg Monitoring ◽  
Power Circuit ◽  
Front End ◽  
Analog Front End

This paper presents a power efficient analog front-end (AFE) for electrocardiogram (ECG) signal monitoring and arrhythmia diagnosis. The AFE uses low-noise and low-power circuit design methodologies and aggressive voltage scaling to satisfy both the low power consumption and low input-referred noise requirements of ECG signal acquisition systems. The AFE was realized with a three-stage fully differential AC-coupled amplifier, and it provides bio-signal acquisition with programmable gain and bandwidth. The AFE was implemented in a 130 nm CMOS process, and it has a measured tunable mid-band gain from 31 to 52 dB with tunable low-pass and high-pass corner frequencies. Under only 0.5 V supply voltage, it consumes 68 nW of power with an input-referred noise of 2.8 µVrms and a power efficiency factor (PEF) of 3.9, which makes it very suitable for energy-harvesting applications. The low-noise 68nW AFE was also integrated on a self-powered physiological monitoring System on Chip (SoC) that is used to capture ECG bio-signals. Heart rate extraction (R-R) detection algorithms were implemented and utilized to analyze the ECG data received by the AFE, showing the feasibility of <100 nW AFE for continuous ECG monitoring applications.

scholarly journals 22nm FINFET Based High Gain Wide Band Differential Amplifier

2021 ◽  
Vol 15 ◽  
pp. 55-62
Author(s):  
G Vasudeva ◽  
Uma B. V.
Keyword(s):  
Performance Metrics ◽  
Dynamic Range ◽  
High Gain ◽  
Low Noise ◽  
Vlsi Circuits ◽  
Differential Amplifier ◽  
Model Parameters ◽  
Front End ◽  
Analog Front End ◽  
High K

Differential Amplifier is a primary building block of analog and mixed signal circuit for pre-processing and signal conditioning of analog signal. FINFET devices with high-k gate oxide at 22nm technology are predominantly used for high speed and low power complex VLSI circuits. FINFET based differential amplifiers are widely used in ADC’s and signal Processing applications due to their advantages in terms of power dissipation. Analog front end of complex VLSI circuits need to offer high gain, higher stability and low noise figure. Designing of FINFET based VLSI sub-circuits requires proper design procedure that can provide designers flexibility in controlling the circuit performances. In this paper, differential amplifier is designed using model parameters of high-k FINFET in 22nm technology. The conventional procedures for designing MOSFET based differential amplifier are modified for designing FINFET based differential amplifier. Schematic capture is carried out in Cadence environment and simulations are obtained considering 22nm FINFET PDK. The performance metrics are evaluated and optimized considering multiple iterations. The designed differential amplifier has slew rate of 6V/µSec and settling time of 0.9 µSec which is a desired metric for ADCs. Power Supply Rejection Ratio (PSRR) is 83 dB and dynamic range is 1.6754 V. Open loop DC gain of DA is achieved to be 103 dB with phase margin of 630 that demonstrates the advantages of DA designed in this work suitable for analog front end

Sign in / Sign up

Export Citation Format

Share Document