Effect of constant and variable radii fillet on secondary flow field of transonic turbine stage's Nozzle Guide Vane

2016 ◽  
Author(s):  
K. Ananthakrishnan ◽  
M. Govardhan
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Guide Vane ◽  
Nozzle Guide Vane ◽  
Transonic Turbine ◽  
Nozzle Guide ◽  
Secondary Flow Field

On the Unsteady Formation of Secondary Flow Inside a Rotating Turbine Blade Passage

2013 ◽  
Vol 136 (6) ◽  
Author(s):  
C. M. Schneider ◽  
D. Schrack ◽  
M. Kuerner ◽  
M. G. Rose ◽  
S. Staudacher ◽  
...  
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Guide Vane ◽  
Low Pressure ◽  
Flow Structures ◽  
Low Pressure Turbine ◽  
Interaction Processes ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Secondary Flow Field

This paper addresses the unsteady formation of secondary flow structures inside a turbine rotor passage. The first stage of a two-stage, low-pressure turbine is investigated at a Reynolds Number of 75,000. The design represents the third and the fourth stages of an engine-representative, low-pressure turbine. The flow field inside the rotor passage is discussed in the relative frame of reference using the streamwise vorticity. A multistage unsteady Reynolds-averaged Navier–Stokes (URANS) prediction provides the time-resolved data set required. It is supported by steady and unsteady area traverse data acquired with five-hole probes and dual-film probes at rotor inlet and exit. The unsteady analysis reveals a nonclassical secondary flow field inside the rotor passage of this turbine. The secondary flow field is dominated by flow structures related to the upstream nozzle guide vane. The interaction processes at hub and casing appear to be mirror images and have characteristic forms in time and space. Distinct loss zones are identified, which are associated with vane-rotor interaction processes. The distribution of the measured isentropic stage efficiency at rotor exit is shown, which is reduced significantly by the secondary flow structures discussed. Their impacts on the steady as well as on the unsteady angle characteristics at rotor exit are presented to address the influences on the inlet conditions of the downstream nozzle guide vane. It is concluded that URANS should improve the optimization of rotor geometry and rotor loss can be controlled, to a degree, by nozzle guide vane (NGV) design.

On the Unsteady Formation of Secondary Flow Inside a Rotating Turbine Blade Passage

2013 ◽  
Author(s):  
C. M. Schneider ◽  
D. Schrack ◽  
M. Kuerner ◽  
M. G. Rose ◽  
S. Staudacher ◽  
...  
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Guide Vane ◽  
Low Pressure ◽  
Flow Structures ◽  
Low Pressure Turbine ◽  
Interaction Processes ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Secondary Flow Field

This paper addresses the unsteady formation of secondary flow structures inside a turbine rotor passage. The first stage of a two-stage low pressure turbine is investigated at a Reynolds Number of 75 000. The design represents the third and the fourth stages of an engine representative low pressure turbine. The flow field inside the rotor passage is discussed in the relative frame of reference using the streamwise vorticity. A multi-stage URANS prediction provides the time-resolved data set required. It is supported by steady and unsteady area traverse data acquired with five-hole probes and dual-film probes at rotor inlet and exit. The unsteady analysis reveals a non-classical secondary flow field inside the rotor passage of this turbine. The secondary flow field is dominated by flow structures related to the upstream nozzle guide vane. The interaction processes at hub and casing appear to be mirror images and have characteristic forms in time and space. Distinct loss zones are identified which are associated with vane-rotor interaction processes. The distribution of the measured isentropic stage efficiency at rotor exit is shown which is reduced significantly by the secondary flow structures discussed. Their impacts on the steady as well as on the unsteady angle characteristics at rotor exit are presented to address the influences on the inlet conditions of the downstream nozzle guide vane.

Numerical Investigations of Geometric Design Parameters Defining Nozzle Guide Vane Endwall Heat Transfer

2006 ◽  
Author(s):  
Frank G. Rubensdo¨rffer ◽  
Torsten H. Fransson
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Combustion Chamber ◽  
Guide Vane ◽  
Heat Shield ◽  
Nozzle Guide Vane ◽  
Transfer Pattern ◽  
Nozzle Guide ◽  
Cooling Air ◽  
Secondary Flow Field

The objective of this work is to compare the predicted flow field and the endwall heat transfer of a baseline nozzle guide vane configuration with a combustion chamber variant, a heat shield variant without and with additional cooling air, and a cavity variant without and with additional cooling air. The comparison is carried out numerically using the commercial 3D Navier-Stokes software package Fluent [1]. For the turbulence modeling the v2-f model by Durbin [2] been used. The detailed comparison of the flow field and the endwall heat transfer shows major differences between the baseline and heat shield configuration. The heat shield in front of the airfoil of the nozzle guide vane cascade influences the secondary flow field and the endwall heat transfer pattern strongly. The additional cooling air, released under the heat shield also has a distinctive influence. The cavity between the combustion chamber and the nozzle guide vane affects the secondary flow field and the endwall heat transfer pattern. Here the influence of the additional cavity cooling air is more decisive.

Flow Measurements in a Nozzle Guide Vane Passage With a Low Aspect Ratio and Endwall Contouring

2000 ◽  
Author(s):  
Steven W. Burd ◽  
Terrence W. Simon
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Guide Vane ◽  
Flow Measurements ◽  
Vast Number ◽  
Aspect Ratios ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

The vast number of turbine cascade studies in the literature has been performed in straight-endwall, high-aspect-ratio, linear cascades. As a result, there has been little appreciation for the role of, and added complexity imposed by, reduced aspect ratios. There also has been little documentation of endwall profiling at these reduced spans. To examine the role of these factors on cascade hydrodynamics, a large-scale nozzle guide vane simulator was constructed at the Heat Transfer Laboratory of the University of Minnesota. This cascade is comprised of three airfoils between one contoured and one flat endwall. The geometries of the airfoils and endwalls, as well as the experimental conditions in the simulator, are representative of those in commercial operation. Measurements with hot-wire anemometry were taken to characterize the flow approaching the cascade. These measurements show that the flow field in this cascade is highly elliptic and influenced by pressure gradients that are established within the cascade. Exit flow field measurements with triple-sensor anemometry and pressure measurements within the cascade indicate that the acceleration imposed by endwall contouring and airfoil turning is able to suppress the size and strength of key secondary flow features. In addition, the flow field near the contoured endwall differs significantly from that adjacent to the straight endwall.

Experimental Investigations and Numerical Validation of an Outlet Guide Vane With an Engine Mount Recess

2008 ◽  
Author(s):  
Johan Hja¨rne ◽  
Valery Chernoray ◽  
Jonas Larsson
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Guide Vane ◽  
Test Facility ◽  
Experimental Investigations ◽  
Flow Angle ◽  
Sst Model ◽  
Engine Mount ◽  
Inlet Conditions ◽  
Secondary Flow Field

This paper presents experiments and CFD calculations of a Low Pressure Turbine/Outlet Guide Vane (LPT/OGV) equipped with an engine mount recess (a bump) tested in the Chalmers linear LPT/OGV cascade. The investigated characteristics include performance for the design point in terms of total pressure loss and turning as well as a detailed description of the downstream development of the secondary flow field. The numerical simulations are performed for the same inlet conditions as in the test-facility with engine-like properties in terms of Reynolds number, boundary-layer thickness and inlet flow angle. The objective is to validate how accurately and reliably the secondary flow field and losses can be predicted for an LPT/OGV equipped with a bump. Three different turbulent models as implemented in FLUENT, the k-ε realizable model, the kω-SST model and the RSM are validated against detailed measurements. From these results it can be concluded that the kω-SST model predicts both the secondary flow field and the losses most accurately.

Aero-Thermal Performance of a Two-Dimensional Highly Loaded Transonic Turbine Nozzle Guide Vane: A Test Case for Inviscid and Viscous Flow Computations

1992 ◽  
Vol 114 (1) ◽  
pp. 147-154 ◽  
Author(s):  
T. Arts ◽  
M. Lambert de Rouvroit
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Static Pressure ◽  
Free Stream ◽  
Guide Vane ◽  
Free Stream Turbulence ◽  
Nozzle Guide Vane ◽  
Transonic Turbine ◽  
Nozzle Guide ◽  
Highly Loaded

This contribution deals with an experimental aero-thermal investigation around a highly loaded transonic turbine nozzle guide vane mounted in a linear cascade arrangement. The measurements were performed in the von Karman Institute short duration Isentropic Light Piston Compression Tube facility allowing a correct simulation of Mach and Reynolds numbers as well as of the gas to wall temperature ratio compared to the values currently observed in modern aero engines. The experimental program consisted of flow periodicity checks by means of wall static pressure measurements and Schlieren flow visualizations, blade velocity distribution measurements by means of static pressure tappings, blade convective heat transfer measurements by means of platinum thin films, downstream loss coefficient and exit flow angle determinations by using a new fast traversing mechanism, and free-stream turbulence intensity and spectrum measurements. These different measurements were performed for several combinations of the free-stream flow parameters looking at the relative effects on the aerodynamic blade performance and blade convective heat transfer of Mach number, Reynolds number, and free-stream turbulence intensity.

scholarly journals Aero-Thermal Performance of a Two Dimensional Highly Loaded Transonic Turbine Nozzle Guide Vane: A Test Case for Inviscid and Viscous Flow Computations

1990 ◽  
Author(s):  
Tony Arts ◽  
Muriel Lambert De Rouvroit
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Turbulence Intensity ◽  
Static Pressure ◽  
Guide Vane ◽  
Nozzle Guide Vane ◽  
Transonic Turbine ◽  
Nozzle Guide ◽  
Highly Loaded

This contribution deals with an experimental aero-thermal investigation around a highly loaded transonic turbine nozzle guide vane mounted in a linear cascade arrangement. The measurements were performed in the von Karman Institute short duration Isentropic Light Piston Compression Tube facility allowing a correct simulation of Mach and Reynolds numbers as well as of the gas to wall temperature ratio compared to the values currently observed in modern aero engines. The experimental programme consisted of flow periodicity checks by means of wall static pressure measurements and Schlieren flow visualizations, blade velocity distribution measurements by means of static pressure tappings, blade convective heat transfer measurements by means of platinum thin films, downstream loss coefficient and exit flow angle determinations by using a new fast traversing mechanism and freestream turbulence intensity and spectrum measurements. These different measurements were performed for several combinations of the freestream flow parameters looking at the relative effects on the aerodynamic blade performance and blade convective heat transfer of Mach number, Reynolds number and freestream turbulence intensity.

Measurements of Hub Flow Interaction on Film Cooled Nozzle Guide Vane in Transonic Annular Cascade

2015 ◽  
Vol 137 (8) ◽  
Author(s):  
Lamyaa A. El-Gabry ◽  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Film Cooling ◽  
Guide Vane ◽  
Leading Edge ◽  
Field Measurements ◽  
Co2 Concentration ◽  
Horseshoe Vortex ◽  
Mainstream Flow ◽  
Nozzle Guide

An experimental study has been performed in a transonic annular sector cascade of nozzle guide vanes (NGVs) to investigate the aerodynamic performance and the interaction between hub film cooling and mainstream flow. The focus of the study is on the endwalls, specifically the interaction between the hub film cooling and the mainstream. Carbon dioxide (CO2) has been supplied to the coolant holes to serve as tracer gas. Measurements of CO2 concentration downstream of the vane trailing edge (TE) can be used to visualize the mixing of the coolant flow with the mainstream. Flow field measurements are performed in the downstream plane with a five-hole probe to characterize the aerodynamics in the vane. Results are presented for the fully cooled and partially cooled vane (only hub cooling) configurations. Data presented at the downstream plane include concentration contour, axial vorticity, velocity vectors, and yaw and pitch angles. From these investigations, secondary flow structures such as the horseshoe vortex, passage vortex, can be identified and show the cooling flow significantly impacts the secondary flow and downstream flow field. The results suggest that there is a region on the pressure side (PS) of the vane TE where the coolant concentrations are very low suggesting that the cooling air introduced at the platform upstream of the leading edge (LE) does not reach the PS endwall, potentially creating a local hotspot.

Measurements of Hub Flow Interaction on Film Cooled Nozzle Guide Vane in Transonic Annular Cascade

2012 ◽  
Author(s):  
Lamyaa A. El-Gabry ◽  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Film Cooling ◽  
Guide Vane ◽  
Leading Edge ◽  
Field Measurements ◽  
Co2 Concentration ◽  
Pressure Side ◽  
Trailing Edge ◽  
Nozzle Guide

An experimental study has been performed in a transonic annular sector cascade of nozzle guide vanes to investigate the aerodynamic performance and the interaction between hub film cooling and mainstream flow. The focus of the study is on the endwalls, specifically the interaction between the hub film cooling and the mainstream. Carbon dioxide (CO2) has been supplied to the coolant holes to serve as tracer gas. Measurements of CO2 concentration downstream of the vane trailing edge can be used to visualize the mixing of the coolant flow with the mainstream. Flow field measurements are performed in the downstream plane with a 5-hole probe to characterize the aerodynamics in the vane. Results are presented for the fully cooled and partially cooled vane (only hub cooling) configurations. Data presented at the downstream plane include concentration contour, axial vorticity, velocity vectors, and yaw and pitch angles. From these investigations, secondary flow structures such as the horseshoe vortex, passage vortex, can be identified and show the cooling flow significantly impacts the secondary flow and downstream flow field. The results suggest that there is a region on the pressure side of the vane trailing edge where the coolant concentrations are very low suggesting that the cooling air introduced at the platform upstream of the leading edge does not reach the pressure side endwall, potentially creating a local hotspot.

scholarly journals Wake Region Measurements of a Highly Three-Dimensional Nozzle Guide Vane Tested at DRA Pyestock Using Particle Image Velocimetry

1994 ◽  
Author(s):  
M. Funes-Gallanzi ◽  
P. J. Bryanston-Cross ◽  
K. S. Chana
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Guide Vane ◽  
Three Dimensional ◽  
Light Sheet ◽  
Test Facility ◽  
Velocity Mapping ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Annular Cascade

The quantitative whole field flow visualization technique of PIV has over the last few years been successfully demonstrated for transonic flow applications. A series of such measurements has been made at DRA Pyestock. Several of the development stages critical to a full engine application of the work have now been achieved using the Isentropic Light Piston Cascade (ILPC) test facility operating with high inlet turbulence levels: • A method of seeding the flow with 0.5μm diameter styrene particles has provided an even coverage of the flow field. • A method of projecting a 1 mm thick high power Nd/YAG laser light sheet within the turbine stator cascade. This has enabled a complete instantaneous intra-blade velocity mapping of the flow field to be visualized, by a specially developed diffraction-limited optics arrangement. • Software has been developed to automatically analyze the data. Due to the sparse nature of the data obtained, a spatial approach to the extraction of the velocity vector data was employed. • Finally, a comparison of the experimental results with those obtained from a three-dimensional viscous flow program of Dawes; using the Baldwin-Lomax model for eddy viscosity and assuming fully turbulent flow. The measurements provide an instantaneous quantitative whole field visualization of a high-speed unsteady region of flow in a highly three-dimensional nozzle guide vane; which has been successfully compared with a full viscous calculation. This work represents the first such measurements to be made in a full-size transonic annular cascade at engine representative conditions.

Sign in / Sign up

Export Citation Format

Share Document