Fault Simulation and Diagnosis of Vacuum System Based on a Simulation Platform

2010 ◽  
Author(s):  
Li Qing ◽  
Xu Zhihua ◽  
Hu Niansu ◽  
Li Jun
Keyword(s):  
Fault Simulation ◽  
Vacuum System ◽  
Simulation Platform

Construction of network fault simulation platform and event samples acquisition techniques for event correlation

2001 ◽  
Vol 6 (3) ◽  
pp. 670-674
Author(s):  
Su Yu-bei ◽  
Wang Zhi ◽  
Cao Yang ◽  
Huang Tian-xi ◽  
Wang Li-na
Keyword(s):  
Fault Simulation ◽  
Simulation Platform ◽  
Event Correlation ◽  
Network Fault

scholarly journals Fault simulation platform of gear transmission system based on Labview

2019 ◽  
Vol 242 ◽  
pp. 032052
Author(s):  
Junguo Wang ◽  
Yang Yang ◽  
Rui Sun ◽  
Minqiang Ren ◽  
Yongxiangn Zhao
Keyword(s):  
Fault Simulation ◽  
Transmission System ◽  
Gear Transmission ◽  
Simulation Platform ◽  
Gear Transmission System

Replication of Wet Objects and Cells

1974 ◽  
Vol 32 ◽  
pp. 102-103
Author(s):  
S. Basu ◽  
D. F. Parsons
Keyword(s):  
Water Vapor Pressure ◽  
High Vacuum ◽  
Polystyrene Latex ◽  
Vacuum System ◽  
Saturated Water Vapor ◽  
Replication Method ◽  
New Methods ◽  
Saturated Water ◽  
Water Vapors ◽  
Intermediate Chamber

We are approaching the invasiveness of cancer cells from the studies of their wet surface morphology which should distinguish them from their normal counterparts. In this report attempts have been made to provide physical basis and background work to a wet replication method with a differentially pumped hydration chamber (Fig. 1) (1,2), to apply this knowledge for obtaining replica of some specimens of known features (e.g. polystyrene latex) and finally to realize more specific problems and to improvize new methods and instrumentation for their rectification. In principle, the evaporant molecules penetrate through a pair of apertures (250, 350μ), through water vapors and is, then, deposited on the specimen. An intermediate chamber between the apertures is pumped independently of the high vacuum system. The size of the apertures is sufficiently small so that full saturated water vapor pressure is maintained near the specimen.

Vacuum System to Minimize the Specimen Contamination of High-Performance EM

1977 ◽  
Vol 35 ◽  
pp. 68-69
Author(s):  
N. Yoshimura ◽  
K. Shirota ◽  
T. Etoh
Keyword(s):  
Electron Microscope ◽  
High Speed ◽  
High Performance ◽  
High Vacuum ◽  
Vacuum System ◽  
Pump System ◽  
Pumping System ◽  
Diffusion Pump ◽  
Almost All ◽  
Cascade Type

One of the most important requirements for a high-performance EM, especially an analytical EM using a fine beam probe, is to prevent specimen contamination by providing a clean high vacuum in the vicinity of the specimen. However, in almost all commercial EMs, the pressure in the vicinity of the specimen under observation is usually more than ten times higher than the pressure measured at the punping line. The EM column inevitably requires the use of greased Viton O-rings for fine movement, and specimens and films need to be exchanged frequently and several attachments may also be exchanged. For these reasons, a high speed pumping system, as well as a clean vacuum system, is now required. A newly developed electron microscope, the JEM-100CX features clean high vacuum in the vicinity of the specimen, realized by the use of a CASCADE type diffusion pump system which has been essentially improved over its predeces- sorD employed on the JEM-100C.

A Superconducting Microscope

1971 ◽  
Vol 29 ◽  
pp. 10-11 ◽  
Author(s):  
R. E. Worsham ◽  
J. E. Mann ◽  
E. G. Richardson
Keyword(s):  
Liquid Helium ◽  
Focal Length ◽  
Vacuum System ◽  
Objective Lens ◽  
Electrical Instability ◽  
Radiation Shields ◽  
And Control ◽  
Thermal Oscillations ◽  
Flux Pump

This superconducting microscope, Figure 1, was first operated in May, 1970. The column, which started life as a Siemens Elmiskop I, was modified by removing the objective and intermediate lenses, the specimen chamber, and the complete vacuum system. The large cryostat contains the objective lens and stage. They are attached to the bottom of the 7-liter helium vessel and are surrounded by two vapor-cooled radiation shields.In the initial operational period 5-mm and 2-mm focal length objective lens pole pieces were used giving magnification up to 45000X. Without a stigmator and precision ground pole pieces, a resolution of about 50-100Å was achieved. The boil-off rate of the liquid helium was reduced to 0.2-0.3ℓ/hour after elimination of thermal oscillations in the cryostat. The calculated boil-off was 0.2ℓ/hour. No effect caused by mechanical or electrical instability was found. Both 4.2°K and 1.7-1.9°K operation were routine. Flux pump excitation and control of the lens were quite smooth, simple, and, apparently highly stable. Alignment of the objective lens proved quite awkward, however, with the long-thin epoxy glass posts used for supporting the lens.

Sign in / Sign up

Export Citation Format

Share Document