3D FEA investigation of the PM segmentation on the iron loss of fractional-slot machines

2014 ◽  
Author(s):  
Asma Masmoudi ◽  
Ahmed Masmoudi
Keyword(s):  
Slot Machines ◽  
Iron Loss ◽  
3D Fea ◽  
Fractional Slot

scholarly journals Design for Reliability: The Case of Fractional-Slot Surface Permanent-Magnet Machines

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1691 ◽  
Author(s):  
Ambra Torreggiani ◽  
Claudio Bianchini ◽  
Matteo Davoli ◽  
Alberto Bellini
Keyword(s):  
Permanent Magnet ◽  
High Efficiency ◽  
Slot Machines ◽  
Design Parameters ◽  
Permanent Magnet Machines ◽  
Design Phase ◽  
Manufacturing Defects ◽  
Design For Reliability ◽  
Reliability Method ◽  
Fractional Slot

Surface permanent-magnet machines are widely used in different applications, from industrial automation to home appliance and electrical traction. Among any possible machine topology, the fractional-slot surface permanent-magnet one has gained increasing importance, because of its high torque density, low cogging torque, extended flux weakening capability and high efficiency. In addition, fractional-slot machines are attractive for tooth concentrated windings, which allow some optimized manufacturing solutions such as modular stator tooth and high slot filling factor, which result in copper volume reduction; cost reduction, and lower stator parasitic resistances. The slot–pole combination is one of the most important design parameter and, as shown in this paper, it affects performances and the robustness of the machine with respect to the manufacturing imperfections. In the literature, slot–pole combinations are optimized at design phase by finite-element analysis relying on a healthy machine model. The original contribution of this paper is a design for reliability method that models manufacturing defects and includes them at design phase in the optimization process of slot–pole combinations. A method is presented that allows defining the optimal design parameters for maximum performances and robustness towards unavoidable imperfections caused by tolerances of the manufacturing process.

Influence of unbalanced magnetic force on shaft deflection in permanent magnet synchronous motor with fractional slot concentrated windings

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1461-1468
Author(s):  
Ting Dong ◽  
Juyan Huang ◽  
Bing Peng ◽  
Ling Jian
Keyword(s):  
Permanent Magnet ◽  
Magnetic Force ◽  
Permanent Magnet Synchronous Motor ◽  
Operational Reliability ◽  
Topology Structure ◽  
Permanent Magnet Synchronous Motors ◽  
Synchronous Motors ◽  
Shaft Deflection ◽  
Large Length ◽  
Fractional Slot

The calculation accuracy of unbalanced magnetic forces (UMF) is very important to the design of rotor length, because it will effect the shaft deflection. But in some permanent magnet synchronous motors (PMSMs) with fractional slot concentrated windings (FSCW), the UMF caused by asymmetrical stator topology structure is not considered in the existing deflection calculation, which is very fatal for the operational reliability, especially for the PMSMs with the large length-diameter ratio, such as submersible PMSMs. Therefore, the part of UMF in the asymmetrical stator topology structure PMSMs caused by the choice of pole-slot combinations is analysized in this paper, and a more accurate rotor deflection calculation method is also proposed.

Measuring Iron Loss of the Electrical Steel Sheets with Different Grades under Compressive Stress Normal to the Surface

2019 ◽  
Vol 139 (4) ◽  
pp. 190-196
Author(s):  
Shinya Urata ◽  
Yoshitaka Maeda ◽  
Hideo Nakai ◽  
Yuuya Takeuchi ◽  
Kyyoul Yun ◽  
...  
Keyword(s):  
Compressive Stress ◽  
Electrical Steel ◽  
Iron Loss ◽  
Steel Sheets ◽  
Electrical Steel Sheets
Sign in / Sign up

Export Citation Format

Share Document