Warpage Control of Liquid Molding Compound for Fan-Out Wafer Level Packaging

2018 ◽  
Author(s):  
Yosuke Oi ◽  
Yasuhito Fujii ◽  
Takashi Hiraoka ◽  
Yukio Yada ◽  
Katsushi Kan
Keyword(s):  
Wafer Level ◽  
Molding Compound ◽  
Wafer Level Packaging ◽  
Liquid Molding

Fan-Out Wafer-Level Packaging (FOWLP) of Large Chip with Multiple Redistribution Layers (RDLs)

2017 ◽  
Vol 14 (4) ◽  
pp. 123-131 ◽  
Author(s):  
John Lau ◽  
Ming Li ◽  
Nelson Fan ◽  
Eric Kuah ◽  
Zhang Li ◽  
...  
Keyword(s):  
Thin Layer ◽  
Glass Wafer ◽  
Front Side ◽  
Wafer Level ◽  
Molding Compound ◽  
The Third ◽  
Wafer Level Packaging ◽  
Die Attach ◽  
Solder Balls ◽  
Test Package

This study is for fan-out wafer-level packaging with chip-first (die face-up) formation. Chips with Cu contact-pads on the front side and a die attach film on the backside are picked and placed face-up on a temporary-glass-wafer carrier with a thin layer of light-to-heat conversion material. It is followed by compression molding with an epoxy molding compound (EMC) and a post-mold cure on the reconstituted wafer carrier and then backgrinding the molded EMC to expose the Cu contact-pads of the chips. The next step is to build up the redistribution layers (RDLs) from the Cu contact-pads and then mount the solder balls. This is followed by the debonding of the carrier with a laser and then the dicing of the whole reconstituted wafer into individual packages. A 300-mm reconstituted wafer with a package/die ratio = 1.8 and a die-top EMC cap = 100 μm has also been fabricated (a total of 325 test packages on the reconstituted wafer). This test package has three RDLs; the line width/spacing of the first RDL is 5 μm/5 μm, of the second RDL is 10 μm/10 μm, and of the third RDL is 15 μm/15 μm. The dielectric layer of the RDLs is fabricated with a photosensitive polyimide and the conductor layer of the RDLs is fabricated by electrochemical Cu deposition (ECD).

Warpage Characterization of Molded Wafer for Fan-Out Wafer-Level Packaging

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Hsien-Chie Cheng ◽  
Yan-Cheng Liu
Keyword(s):  
Measurement Data ◽  
Mechanical Analysis ◽  
Volumetric Shrinkage ◽  
Heat Of Reaction ◽  
Wafer Level ◽  
Molding Process ◽  
Scanning Calorimetry ◽  
Molding Compound ◽  
Wafer Level Packaging

Abstract This study presents a comprehensive assessment of the process-induced warpage of molded wafer for chip-first, face-down fan-out wafer-level packaging (FOWLP) during the fan-out fabrication process. A process-dependent simulation methodology is introduced, which integrates nonlinear finite element (FE) analysis and element death-birth technique. The effects of the cure-dependent volumetric shrinkage, geometric nonlinearity, and gravity loading on the process-induced warpage are examined. The study starts from experimental characterization of the temperature-dependent material properties of the applied liquid type epoxy molding compound (EMC) system through dynamic mechanical analysis (DMA) and thermal mechanical analysis. Furthermore, its cure state (heat of reaction and degree of cure (DOC)) during the compression molding process (CMP) is measured by differential scanning calorimetry (DSC) tests. Besides, the cure dependent-volumetric (chemical) shrinkages of the EMC system after the in-mold cure (IMC) and postmold cure (PMC) are experimentally determined by which the volumetric shrinkage at the gelation point is predicted through a linear extrapolation approach. To demonstrate the effectiveness of the proposed theoretical model, the prediction results are compared against the inline warpage measurement data. One possible cause of the asymmetric/nonaxisymmetric warpage is also addressed. Finally, the influences of some geometric dimensions on the warpage of the molded wafer are identified through parametric analysis.

SiP(System in Package) Solutions with Wafer Level Packaging Technology

2011 ◽  
Vol 2011 (DPC) ◽  
pp. 002226-002253 ◽  
Author(s):  
In Soo Kang ◽  
Jong Heon (Jay) Kim
Keyword(s):  
Embedded System ◽  
High Performance ◽  
Low Cost ◽  
Wafer Level ◽  
Molding Compound ◽  
Wafer Level Packaging ◽  
Ic Packaging ◽  
Chip Size ◽  
Bonding Technology ◽  
Small Form Factor

In mobile application, the WLP technology has been developing to make whole package size almost same as chip size. However, the I/O per chip unit area has increased so that it gets difficult to realize ideal pad pitch for better reliability. Recently, to achieve the thin and small size, high performance and low cost semiconductor package, Embedding Die and Fanout Technologies have been suggested and developed based on wafer level processing. In this work, as a solution of system in package, wafer level embedded package and fanout technology will be reviewed. Firstly, Wafer level embedded System in Package (WL-eSiP) which has daughter chip (small chip) embedded inside mother chip (bigger chip) without any special substrate has been suggested and developed. To realize wafer level embedded system in package (WL-eSiP), wafer level based new processes like wafer level molding for underfilling and encapsulation by molding compound without any special substrate have been applied and developed, including high aspect ratio Cu bumping, mold thinning and chip-to-wafer flipchip bonding. Secondly, Fan-out Package is considered as alternative package structure which means merged package structure of WLCSP (wafer level chip size package) and PCB process. We can make IC packaging widen area for SIP(System in Package) or 3D package. In addition, TSV and IPD are key enabling technology to meet market demands because TSV interconnection can provide wider bandwidth and high transmission speed due to vertical one compared to wire bonding technology and IPD can provide higher performance, more area saving to be assembled and small form factor compared to discrete passive components.

Optimization of laser release layer, glass carrier, and organic build-up layer to enable RDL-first fan-out wafer-level packaging

2016 ◽  
Vol 2016 (1) ◽  
pp. 000190-000195 ◽  
Author(s):  
Alvin Lee ◽  
Jay Su ◽  
Baron Huang ◽  
Ram Trichur ◽  
Dongshun Bai ◽  
...  
Keyword(s):  
High Speed ◽  
Process Integration ◽  
Cost Effective ◽  
Wafer Level ◽  
Molding Compound ◽  
Fine Line ◽  
Glass Substrates ◽  
Laser Ablation Process ◽  
Wafer Level Packaging ◽  
Increasing Demand

Abstract With increasing demand for mobile devices to be lighter and thinner and consume less power while operating at high speed and high bandwidth, many equipment suppliers and assembly participants have invested great efforts to achieve fine-line fan-out wafer-level packaging (FOWLP). However, the inherent warp of reconstituted wafers, which can contribute to poor die placement accuracy and/or delamination at the interface of the build-up layer and carrier, remains a major challenge. In this study, the interactions among laser release layer, glass carrier, and build-up layer were evaluated for optimization of redistribution layer (RDL)–first FOWLP as a foundation to move toward fine-line FOWLP. In this study, a series of experiments incorporating glass carrier, laser release layer, and build-up layers were carried out to determine the optimal setup for RDL-first FOWLP. First, glass carriers (300 mm × 300 mm × 0.7 mm) with coefficients of thermal expansion of 3 and 8 ppm/°C were treated with 150-nm laser release layers. After deposition of 0.1 μm of sacrificial material on the glass carrier, 8-μm build-up layers were coated and patterned by lithography to electroplate Cu interconnections with a density of approximately 10% of the surface area. Subsequent to die attachment, molding compound was applied on top to form a 200-μm protective overcoat. The reconstituted wafer was then separated from the glass carrier through a laser ablation process using a 308-nm laser to complete the design of experiments (DOE). An experiment to study the correlation of glass carrier, laser release layer, build-up layers, and molding compound in RDL-first FOWLP processes is discussed to address full process integration on 300-mm glass substrates. The combination of glass carrier, laser release layer, build-up layer, and molding compound will pave the way for realizing cost-effective RDL-first FOWLP on panel-size substrates.

Self Priming Low Stress Aqueous Developable Benzocyclobutene (AD-BCB) Photodielectric Materials for Advanced Wafer Level Packaging

2015 ◽  
Vol 2015 (DPC) ◽  
pp. 000679-000697
Author(s):  
Hua Dong ◽  
Greg Prokopowicz ◽  
Bob Barr ◽  
Joe Lachowski ◽  
Jeff Calvert ◽  
...  
Keyword(s):  
Silicon Oxide ◽  
High Reliability ◽  
Semiconductor Industry ◽  
Dielectric Materials ◽  
Film Stress ◽  
Wafer Level ◽  
Adhesion Promoter ◽  
Molding Compound ◽  
Wafer Level Packaging ◽  
New Formulation

As the semiconductor industry drives to more functionality in smaller and lighter devices, it requires new materials to meet the changing requirements of new and more advanced chip designs and packaging solutions. Photoimagable polymeric dielectric materials are a key building block for wafer level packaging (WLP); these include polyimide (PI), polybenzoxazole (PBO), acrylics, silicones, epoxy-phenolics and benzocyclobutene (BCB). Because of low copper diffusion, low temperature curing, high reliability and low moisture adsorption, BCB was the platform chosen for modification. In this work, we will focus on the development of self priming, low stress, aqueous developable version of BCB, known as AD-BCB. This new photodielectric material has improved mechanical properties of <25MPa film stress value and >28% elongation while maintaining good post develop and post cure adhesion on various substrates including silicon, silicon oxide, silicon nitride, copper, aluminum and epoxy molding compound. Elongation is significantly increased for this positive tone, aqueous developable, photodielectric materials, while film stress and wafer bow are significantly reduced. In addition, this new formulation is self priming and does not require a spin-on adhesion promoter. The material can be cured at as low as 200 °C with lithographic feature size of <10 μm and dielectric constant of 3.0.

Fan-Out Wafer-Level Packaging (FOWLP) of Large Chip with Multiple Redistribution-Layers (RDLs)

2017 ◽  
Vol 2017 (1) ◽  
pp. 000576-000583 ◽  
Author(s):  
John Lau ◽  
Ming Li ◽  
Nelson Fan ◽  
Eric Kuah ◽  
Zhang Li ◽  
...  
Keyword(s):  
Thin Layer ◽  
Glass Wafer ◽  
Front Side ◽  
Wafer Level ◽  
Molding Compound ◽  
The Third ◽  
Wafer Level Packaging ◽  
Die Attach ◽  
Solder Balls ◽  
Test Package

Abstract This study is for fan-out wafer-level packaging (FOWLP) with chip-first (die face-up) formation. The chips with Cu contact-pads on the front-side and a die attach film (DAF) on the backside are picked and placed face-up on a temporary glass wafer carrier with a thin layer of light-to-heat conversion (LTHC) material. It is followed by compression molding with epoxy molding compound (EMC) and post mold cure (PMC) on the reconstituted wafer carrier, and then backgrinding the molded EMC to expose the Cu contact-pads of the chips. The next step is to build up the redistribution layers (RDLs) from the Cu contact-pads and then mount the solder balls. Next comes the de-bonding of the carrier with a laser, and then the dicing of the whole reconstituted wafer into individual packages. A 300mm reconstituted wafer with a package/die ratio = 1.8 and a die-top EMC cap = 100μm has also been fabricated (a total of 325 test packages on the reconstituted wafer.) This test package has three RDLs; the line width/spacing of the first RDL is 5μm/5μm, of the second RDL is 10μm/10μm, and of the third RDL is 15μm/15μm. The dielectric layer of the RDLs is fabricated with a photosensitive polyimide (PI) and the conductor layer of the RDLs is fabricated by electrochemical Cu deposition (ECD).

Mechanical Analyses of Advanced Multi-Chip Embedded Wafer Level Packages

2013 ◽  
Vol 740 ◽  
pp. 289-294
Author(s):  
Siow Ling Ho ◽  
Lin Bu ◽  
Dexter Velez Sorono ◽  
Ser Choong Chong ◽  
Tai Chong Chai ◽  
...  
Keyword(s):  
Cycling Performance ◽  
Market Demand ◽  
Wafer Level ◽  
Molding Process ◽  
Molding Compound ◽  
Mechanical Effects ◽  
Wafer Level Packaging ◽  
Attractive Option ◽  
Small Form Factor ◽  
Improved Accuracy

ncreasing functionality accompanied with device miniaturization in microelectronics has led to increased market demand for packages with small form factor. Over the years, embedded wafer level packaging (EWLP) has become an attractive option since it allows a reduction in package size and height. In the EWLP approach, the singulated dies are embedded within the molding compound through the wafer level compression molding process. For this study, critical mechanical challenges such as die shift and thermal cycling performance of a multi-chip embedded wafer level package (MCEWLP) are addressed through numerical modeling. For improved accuracy in die shift predictions, both mechanical effects and fluidic effects need to be taken into account. Mechanical effects account for around 75% of the die shift while fluidic effect contributes to the remaining 25%. It is shown that reducing the die size and the inclusion of UBM as a buffer layer can effectively increase the fatigue life of the packages.

Sign in / Sign up

Export Citation Format

Share Document