Dependence of solder joint reliability on solder volume, Composition and printed circuit board surface finish

2014 ◽  
Author(s):  
Babak Arfaei ◽  
Francis Mutuku ◽  
Keith Sweatman ◽  
Ning-Cheng Lee ◽  
Eric Cotts ◽  
...  
Keyword(s):  
Solder Joint ◽  
Surface Finish ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Solder Joint Reliability ◽  
Printed Circuit ◽  
Joint Reliability ◽  
Solder Volume ◽  
Board Surface

Effects of Void, Crack, and PCB Thickness on the Solder Joint Reliability of Wafer-Level Chip-Scale Package (WLCSP) Assemblies

2002 ◽  
Author(s):  
John Lau ◽  
Yida Zou ◽  
Sergio Camerlo
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Temperature Cycling ◽  
Circuit Board ◽  
J Integral ◽  
Wafer Level ◽  
Solder Joint Reliability ◽  
Printed Circuit ◽  
Joint Reliability ◽  
Chip Scale Package

The creep analyses of solder-bumped wafer-level chip-scale package (WLCSP) on printed circuit board (PCB) subjected to temperature cycling loading are presented. Emphasis is placed on the effects of PCB thickness on the solder joint reliability of the WLCSP assembly. Also, the effects of crack-length on the crack tip characteristics such as the J-integral in the WLCSP solder joint are studied by the fracture mechanics method. Finally, the effects of voids on the crack growth in the WLCSP solder joint are investigated.

scholarly journals Improving the Solder Joint Reliability of a Power Leadframe Package Using Thermomechanical Simulation

2019 ◽  
pp. 1-6
Author(s):  
Jefferson Talledo
Keyword(s):  
Solder Joint ◽  
Heat Dissipation ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Mold Material ◽  
Element Analysis ◽  
Solder Joint Reliability ◽  
Joint Reliability ◽  
Thermomechanical Simulation ◽  
Board Level

Leadframe-based packages are commonly used for semiconductor power devices. With these packages, heat dissipation is much better compared with laminate substrated-based packages. However, the solder joint reliability requirement under thermal cycling condition is also higher and this is what makes the development of a power package challenging. One of the usual requirements from customers is that there should be no solder joint failure up to 2,000 thermal cycles. This paper presents the thermomechanical simulation of a power leadframe package that was conducted to improve its solder joint reliability. Board level solder joint cycle life was predicted using finite element analysis and the result was validated with actual solder life result from board level reliability evaluation. Since available solder prediction equation was for the characteristic life (63.2% accumulative failure), using the normalized characteristic life was implemented for predicting the number of cycles to first failure of the solder joint connection and the approach showed good agreement with the actual result. Results also indicated that the choice of epoxy mold material and the type of PCB (printed circuit board) have a significant contribution to the solder joint reliability performance.

scholarly journals Study on the Impact of Lead Sidewall Solder Coverage and Corner Lead Size on Joint Reliability

2021 ◽  
pp. 62-69
Author(s):  
Jefferson Talledo
Keyword(s):  
Solder Joint ◽  
Integrated Circuit ◽  
High Speed ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Element Analysis ◽  
Solder Joint Reliability ◽  
Joint Reliability ◽  
Solder Fatigue ◽  
The Impact

Solder joint reliability is very important to ensure that an integrated circuit (IC) semiconductor package is functional within its intended life span as the solder joint establishes electrical connection between the IC and the printed circuit board (PCB). Solder fatigue failure or crack under thermal cycling is one of the common problems with board-mounted packages. There are several factors or package characteristics that have impact on solder fatigue life like package size and material properties of the package components. This paper presents a thermo-mechanical modeling of a leadframe-based semiconductor package to study the impact of lead sidewall solder coverage and corner lead size on the solder joint reliability. Finite element analysis (FEA) technique was used to calculate the solder life considering 50% and 100% package lead sidewall solder coverage as well as smaller and larger critical corner leads of the package. The results of the analysis showed that higher lead sidewall solder coverage and larger lead could significantly increase solder life. Therefore, ensuring lead sidewall solder wettability to have higher solder coverage is beneficial. The study also reveals that packages with side wettable flanks are not only enabling high speed automated optical inspection required for the automotive industry, but they are also providing improved solder joint reliability.

Controlling the Solder Joint Reliability of eWLB Packages in Automotive Radar Applications Using a Design for Reliability Approach

2018 ◽  
Author(s):  
M. Niessner ◽  
G. Haubner ◽  
W. Hartner ◽  
S. Pahlke
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Wafer Level ◽  
Automotive Radar ◽  
Low Loss ◽  
Solder Joint Reliability ◽  
Design For Reliability ◽  
Joint Reliability ◽  
Ball Grid Array Packages

A DfR (Design for Reliability) approach which is systematically based on simulation, sensitivity analysis and experimental validation is applied for identifying, understanding and controlling the key factors which determine the solder joint reliability of eWLB (Embedded Wafer Level Ball Grid Array) packages that carry embedded 77 GHz dies and sit on hybrid PCB (Printed Circuit Board) stacks. The hybrid stack investigated in this work is characteristic to automotive RADAR (Radio Detection And Ranging) applications and consists of one low-loss RF (Radio Frequency) layer and several FR4 layers. In line with previous work [1], the mechanical material properties of the low-loss RF laminate material are found to be the key factor. Simulation is used to systematically screen for mechanical properties which are favorable for achieving a high solder joint reliability on the unconstrained PCBs used for standardized solder joint reliability testing. A simplified virtual assessment of PCBs constrained by the mounting in system module housings is done. Both simulation and experimental results show that RF laminate materials with low Young’s modulus are the class of materials which allows for the highest solder joint reliability for all the conditions investigated in this study.

Materials Characterization of Lead Free Compositions for Minimum Temperature SMT Processes at the SLI-Second Level Interconnect Solder Joint

2004 ◽  
Author(s):  
Norman J. Armendariz ◽  
Prawin Paulraj
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Gold Surface ◽  
Circuit Board ◽  
Lead Free ◽  
Processing Temperature ◽  
The European Union ◽  
Printed Circuit ◽  
Higher Temperature ◽  
Tin Silver Copper

Abstract The European Union is banning the use of Pb in electronic products starting July 1st, 2006. Printed circuit board assemblies or “motherboards” require that planned CPU sockets and BGA chipsets use lead-free solder ball compositions at the second level interconnections (SLI) to attach to a printed circuit board (PCB) and survive various assembly and reliability test conditions for end-use deployment. Intel is pro-actively preparing for this anticipated Pb ban, by evaluating a new lead free (LF) solder alloy in the ternary Tin- Silver-Copper (Sn4.0Ag0.5Cu) system and developing higher temperature board assembly processes. This will be pursued with a focus on achieving the lowest process temperature required to avoid deleterious higher temperature effects and still achieve a metallurgically compatible solder joint. One primary factor is the elevated peak reflow temperature required for surface mount technology (SMT) LF assembly, which is approximately 250 °C compared to present eutectic tin/lead (Sn37Pb) reflow temperatures of around 220 °C. In addition, extended SMT time-above-liquidus (TAL) and subsequent cooling rates are also a concern not only for the critical BGA chipsets and CPU BGA sockets but to other components similarly attached to the same PCB substrate. PCBs used were conventional FR-4 substrates with organic solder preservative on the copper pads and mechanical daisychanged FCBGA components with direct immersion gold surface finish on their copper pads. However, a materials analysis method and approach is also required to characterize and evaluate the effect of low peak temperature LF SMT processing on the PBA SLI to identify the absolute limits or “cliffs” and determine if the minimum processing temperature and TAL could be further lowered. The SLI system is characterized using various microanalytical techniques, such as, conventional optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and microhardness testing. In addition, the SLI is further characterized using macroanalytical techniques such as dye penetrant testing (DPT) with controlled tensile testing for mechanical strength in addition to disbond and crack area mapping to complete the analysis.

Experimental Investigation by Speckle Interferometry of Solder Joint Failure Under Thermomechanical Load Aggravated by Boundary Conditions at Board Level

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
D. N. Borza ◽  
I. T. Nistea
Keyword(s):  
Solder Joint ◽  
Fundamental Frequency ◽  
Printed Circuit Board ◽  
Speckle Interferometry ◽  
Circuit Board ◽  
Joint Failure ◽  
Printed Circuit ◽  
Out Of Plane ◽  
Fringe Patterns ◽  
Board Level

Reliability of electronic assemblies at board level and solder joint integrity depend upon the stress applied to the assembly. The stress is often of thermomechanical or of vibrational nature. In both cases, the behavior of the assembly is strongly influenced by the mechanical boundary conditions created by the printed circuit board (PCB) to casing fasteners. In many previously published papers, the conditions imposed to the fasteners are mostly aiming at an increase of the fundamental frequency and a decrease of static or dynamic displacement values characterizing the deformation. These conditions aim at reducing the fatigue in different parts of these assemblies. In the photomechanics laboratory of INSA Rouen, the origins of solder joint failure have been investigated by means of full-field measurements of the flexure deformation induced by vibrations or by forced thermal convection. The measurements were done both at a global level for the whole printed circuit board assembly (PCBA) and at a local level at the solder joints where failure was reported. The experimental technique used was phase-stepped laser speckle interferometry. This technique has a submicrometer sensitivity with respect to out-of-plane deformations induced by bending and its use is completely nonintrusive. Some of the results were comforted by comparison with a numerical finite elements model. The experimental results are presented either as time-average holographic fringe patterns, as in the case of vibrations, or as wrapped phase patterns, as in the case of deformation under thermomechanical stress. Both types of fringe patterns may be processed so as to obtain the explicit out-of-plane static deformation (or vibration amplitude) maps. Experimental results show that the direct cause of solder joint failure may be a high local PCB curvature produced by a supplementary fastening screw intended to reduce displacements and increase fundamental frequency. The curvature is directly responsible for tensile stress appearing in the leads of a large quad flat pack (QFP) component and for shear in the corresponding solder joints. The general principle of increasing the fundamental frequency and decreasing the static or dynamic displacement values has to be checked against the consequences on the PCB curvature near large electronic devices having high stiffness.

Numerical Model to Simulate the Drop Test of Printed Circuit Board (PCB)

2011 ◽  
Vol 423 ◽  
pp. 26-30
Author(s):  
S. Assif ◽  
M. Agouzoul ◽  
A. El Hami ◽  
O. Bendaou ◽  
Y. Gbati
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Drop Test ◽  
Dynamic Responses ◽  
Circuit Board ◽  
Joint Stress ◽  
Printed Circuit ◽  
Increasing Demand ◽  
Improved Model ◽  
Board Level

Increasing demand for smaller consumer electronic devices with multi-function capabilities has driven the packaging architectures trends for the finer-pitch interconnects, thus increasing chances of their failures. A simulation of the Board Level Drop-Test according to JEDEC (Joint Electron Device Council) is performed to evaluate the solder joint reliability under drop impact test. After good insights to the physics of the problem, the results of the numerical analysis on a simple Euler-Bernoulli beam were validated against analytical analysis. Since the simulation has to be performed on ANSYS Mechanical which is an implicit software, two methods were proposed, the acceleration-input and the displacement-input. The results are the same for both methods. Therefore, the simulation is carried on the real standard model construction of the board package level2. Then a new improved model is proposed to satisfy shape regular element and accuracy. All the models are validated to show excellent first level correlation on the dynamic responses of Printed Circuit Board, and second level correlation on solder joint stress. Then a static model useful for quick design analysis and optimization’s works is proposed and validated. Finally, plasticity behavior is introduced on the solder ball and a non-linear analysis is performed.

Sign in / Sign up

Export Citation Format

Share Document