A 75dB-gain Low-power, Low-noise Amplifier for Low-frequency Bio-signal Recording

2010 ◽  
Author(s):  
Dalila Salhi ◽  
Balwant Godara
Keyword(s):  
Low Power ◽  
Low Frequency ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Noise Amplifier ◽  
Signal Recording

Tunable Low-Power Low-Noise Amplifier for Healthcare Applications

2021 ◽  
Author(s):  
Rafael Vieira ◽  
Nuno Horta ◽  
Nuno Lourenço ◽  
Ricardo Póvoa
Keyword(s):  
Low Power ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Healthcare Applications ◽  
Noise Amplifier

scholarly journals A 219-µW ultra-low power low-noise amplifier for IEEE 802.15.4 based battery powered, portable, wearable IoT applications

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
S. Chrisben Gladson ◽  
Adith Hari Narayana ◽  
V. Thenmozhi ◽  
M. Bhaskar
Keyword(s):  
Low Power ◽  
Ieee 802.15.4 ◽  
Low Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Process Technology ◽  
Ultra Low Power ◽  
Power Mode ◽  
Noise Amplifier

AbstractDue to the increased processing data rates, which is required in applications such as fifth-generation (5G) wireless networks, the battery power will discharge rapidly. Hence, there is a need for the design of novel circuit topologies to cater the demand of ultra-low voltage and low power operation. In this paper, a low-noise amplifier (LNA) operating at ultra-low voltage is proposed to address the demands of battery-powered communication devices. The LNA dual shunt peaking and has two modes of operation. In low-power mode (Mode-I), the LNA achieves a high gain ($$S21$$ S 21 ) of 18.87 dB, minimum noise figure ($${NF}_{min.}$$ NF m i n . ) of 2.5 dB in the − 3 dB frequency range of 2.3–2.9 GHz, and third-order intercept point (IIP3) of − 7.9dBm when operating at 0.6 V supply. In high-power mode (Mode-II), the achieved gain, NF, and IIP3 are 21.36 dB, 2.3 dB, and 13.78dBm respectively when operating at 1 V supply. The proposed LNA is implemented in UMC 180 nm CMOS process technology with a core area of $$0.40{\mathrm{ mm}}^{2}$$ 0.40 mm 2 and the post-layout validation is performed using Cadence SpectreRF circuit simulator.

Low power active shunt feedback CMOS low noise amplifier for wideband wireless systems

Integration ◽  
2019 ◽  
Vol 69 ◽  
pp. 189-197 ◽  
Author(s):  
Asieh Parhizkar Tarighat ◽  
Mostafa Yargholi
Keyword(s):  
Low Power ◽  
Wireless Systems ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Noise Amplifier

scholarly journals Design of Low Power UWB CMOS Low Noise Amplifier using Active Inductor for WLAN Receiver

2018 ◽  
Vol 7 (2.24) ◽  
pp. 448
Author(s):  
S Manjula ◽  
M Malleshwari ◽  
M Suganthy
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Wide Band ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Design System ◽  
Active Inductor ◽  
Chip Area ◽  
Noise Amplifier

This paper presents a low power Low Noise Amplifier (LNA) using 0.18µm CMOS technology for ultra wide band (UWB) applications. gm boosting common gate (CG) LNA is designed to improve the noise performance.  For the reduction of on chip area, active inductor is employed at the input side of the designed LNA for input impedance matching. The proposed UWB LNA is designed using Advanced Design System (ADS) at UWB frequency of 3.1-10.6 GHz. Simulation results show that the gain of 10.74+ 0.01 dB, noise figure is 4.855 dB, input return loss <-13 dB and 12.5 mW power consumption.  

Low power size-efficient CMOS UWB low-noise amplifier design

2008 ◽  
Vol 51 (2) ◽  
pp. 494-496
Author(s):  
Hee-Sauk Jhon ◽  
Ickhyun Song ◽  
Jongwook Jeon ◽  
MinSuk Koo ◽  
Byung-Gook Park ◽  
...  
Keyword(s):  
Low Power ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Amplifier Design ◽  
Noise Amplifier
Sign in / Sign up

Export Citation Format

Share Document