Optical signal quality monitor using direct Q-factor measurement

1999 ◽  
Vol 11 (10) ◽  
pp. 1307-1309 ◽  
Author(s):  
S. Ohteru ◽  
N. Takachio
Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1534
Author(s):  
Remigiusz Rajewski

The banyan-type switching networks, well known in switching theory and called the logdN switching fabrics, are composed of symmetrical switching elements of size d×d. In turn, the modified baseline architecture, called the MBA(N,e,g), is only partially built from symmetrical optical switching elements, and it is constructed mostly from asymmetrical optical switching elements. Recently, it was shown that the MBA(N,e,g) structure requires a lower number of passive as well as active optical elements than the banyan-type switching fabric of the same capacity and functionality, which makes it an attractive solution. However, the optical signal-to-crosstalk ratio for the MBA(N,e,g) was not investigated before. Therefore, in this paper, the optical signal-to-crosstalk ratio in the MBA(N,e,g) was determined. Such crosstalk influences the output signal’s quality. Thus, if such crosstalk is lower, the signal quality is better. The switching fabric proposed in the author’s previous work has lower optical signal losses than a typical Beneš and banyan-type switching networks of this same capacity and functionality, which gives better quality of transmitted optical signals at the switching node’s output. The investigated MBA(N,e,g) architecture also contains one stage fewer than banyan-type network of the same capacity, which is an essential feature from the optical switching point of view.


2012 ◽  
Author(s):  
Xu W. ◽  
S. Belomestnykh ◽  
I. Ben-Zvi ◽  
H. Hahn

2019 ◽  
Vol 40 (1) ◽  
pp. 1-6 ◽  
Author(s):  
Kulwinder Singh ◽  
Manjeet Singh Patterh ◽  
Manjit Singh Bhamrah

Abstract In this paper, dual-order bidirectional pumping schemes of distributed fiber Raman amplifier are compared with standard first-order pumping in wavelength division multiplexed optical transmission systems. The novel comparison analysis is carried out in terms of Optical signal-to-noise ratio and Q-factor, on-off gain and noise figure by varying optical input power and fiber lengths. The results indicate that dual-order schemes present 0.02 dB higher OSNR and 5 dB higher Q-factor in comparison to first-order pumping when input optical power is varied from −4 to 5 dBm. Similarly, there is 4 dB higher on-off gain with dual order comparatively to first order when fiber length varied from 10 to 100 km. However, there is degradation in noise figure and Q-factor due to DRBS noise with dual-order pumping when fiber length from 10 to 100 km. Further, the signal power evolutions along fiber length show that there is 5 dBm improvement for 100 km fiber. The novelty of the work is that comparative analysis exhibits improvement in OSNR, on-off gain and Q-factor using dual-order bidirectional pumping.


2000 ◽  
Vol 36 (3) ◽  
pp. 271 ◽  
Author(s):  
X.S. Rao ◽  
C.K. Ong ◽  
Y.P. Feng

2019 ◽  
Vol 24 (5) ◽  
pp. 115
Author(s):  
Humam Husseinˡ ◽  
Dogu Cagdas Atilla1 ◽  
Essa Essa2 ◽  
Cagatay Aydin1

In recent years, there has been a growing and continuous demand for great (data rates) beyond existing wired and wireless networks. Radio-over-Fiber technology is considered as an efficient and practical solution for providing broadband wireless. In this paper, many techniques are used to implement a system that has the capability to provide a great bit rate, broadband bandwidth, and minimum cost. So Radio-over-Fiber technology was used to modulate the light with radio-signal and transmission the signals through an optical fiber cable. Wavelength-Division-Multiplexing technique was used to send many signals through the same link, and Subcarrier Multiplexing-Amplitude Shift keying as a modulation format. 2Gpbs separate on two channels was transmitted on Single-Mode Fiber. The average results obtained from our experience was as follows: maximum Q factor average = 4.9712925, minimum BER average = 3.63*10-7, total power average (dBm) = -51.1502, the OSNR average (dB) = 52.085 for channel_1. The results of channel_2 were: maximum Q factor average = 5.5901325, minimum BER average = 1.26*10-8, total power average (dBm) = -46.60135, the average of optical signal-to-noise ratio (dB) = 54.65. All the average result that has from our simulation was very good and acceptable. The simulation and performance test of our experience was done using Optisystem 7.0.   http://dx.doi.org/10.25130/tjps.24.2019.100


Sign in / Sign up

Export Citation Format

Share Document