An optical integrated circuit for time-division 2-D velocity measurement

1989 ◽  
Vol 7 (2) ◽  
pp. 364-367 ◽  
Author(s):  
H. Toda ◽  
K. Kasazumi ◽  
M. Haruna ◽  
H. Nishihara
Keyword(s):  
Integrated Circuit ◽  
Velocity Measurement ◽  
Time Division ◽  
Division 2 ◽  
Optical Integrated Circuit

scholarly journals Simultaneous Voltage and Current Measurement Instrumentation Amplifier for ECG and PPG Monitoring

Electronics ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 679
Author(s):  
Jongpal Kim
Keyword(s):  
Integrated Circuit ◽  
Cardiovascular Health ◽  
Current Noise ◽  
Instrumentation Amplifier ◽  
Current Sensing ◽  
Application Specific Integrated Circuit ◽  
Time Division ◽  
Electrocardiogram Ecg ◽  
First Time ◽  
Application Specific

An instrumentation amplifier (IA) capable of sensing both voltage and current at the same time has been introduced and applied to electrocardiogram (ECG) and photoplethysmogram (PPG) measurements for cardiovascular health monitoring applications. The proposed IA can switch between the voltage and current sensing configurations in a time–division manner faster than the ECG and PPG bandwidths. The application-specific integrated circuit (ASIC) of the proposed circuit design was implemented using 180 nm CMOS fabrication technology. Input-referred voltage noise and current noise were measured as 3.9 µVrms and 172 pArms, respectively, and power consumption was measured as 34.9 µA. In the current sensing configuration, a current noise reduction technique is applied, which was confirmed to be a 25 times improvement over the previous version. Using a single IA, ECG and PPG can be monitored in the form of separated ECG and PPG signals. In addition, for the first time, a merged ECG/PPG signal is acquired, which has features of both ECG and PPG peaks.

Exotic Doping for Zno Thin Films: Possibility of Monolithic Optical Integrated Circuit

1999 ◽  
Vol 574 ◽  
Author(s):  
Norifumi Fujimura ◽  
Tamaki Shimura ◽  
Toshifumi Wakano ◽  
Atsushi Ashida ◽  
Taichiro Ito
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Nonlinear Optic ◽  
Integrated Circuit ◽  
Film Surface ◽  
Zno Thin Films ◽  
Process Window ◽  
Electro Optic ◽  
Film Substrate ◽  
Optical Integrated Circuit

AbstractWe propose the application of ZnO:X (X = Li, Mg, N, In, Al, Mn, Gd, Yb etc.) films for a monolithic Optical Integrated Circuit (OIC). Since ZnO exhibits excellent piezoelectric effect and has also electro-optic and nonlinear optic effects and the thin films are easily obtained, it has been studied as one of the important thin film wave guide materials especially for an acoustooptic device[1]. In terms of electro-optic and nonlinear optic effects, however, LiNbO3 or LiTaO3 is superior to ZnO. The most important issue of thin film waveguide using such ferroelectrics is optical losses at the film/substrate interface and the film surface, because the process window to control the surface morphology is very narrow due to their high deposition temperature. Since ZnO can be grown at extremely low temperature, the roughness at the surface and the interface is expected to be minimized. This is the absolute requirement especially for waveguide using a blue or ultraviolet laser. Recently, lasing at the wavelength of ultraviolet, ferroelectric and antiferromagnetic behaviors of ZnO doped with various exotic elements (exotic doping) have been reported. This paper discusses the OIC application of ZnO thin films doped with exotic elements.

Sign in / Sign up

Export Citation Format

Share Document