scholarly journals Incomplete fusion analysis of the Li7 -induced reaction on Nb93 within 3–6.5 MeV/nucleon

2017 ◽  
Vol 96 (4) ◽  
Author(s):  
Deepak Kumar ◽  
Moumita Maiti
Keyword(s):  
Incomplete Fusion ◽  
Fusion Analysis ◽  
Induced Reaction

scholarly journals Li7 -induced reaction on Monat : A study of complete versus incomplete fusion

2017 ◽  
Vol 96 (1) ◽  
Author(s):  
Deepak Kumar ◽  
Moumita Maiti ◽  
Susanta Lahiri
Keyword(s):  
Incomplete Fusion ◽  
Induced Reaction

Selective Corrosion of brazed joint between BNi-2 filler metal and stainless steel 316

1996 ◽  
Vol 54 ◽  
pp. 218-219
Author(s):  
H. S. Kim ◽  
R. U. Lee
Keyword(s):  
Stainless Steel ◽  
Filler Metal ◽  
Surface Preparation ◽  
Optical Microscope ◽  
Heating Element ◽  
Incomplete Fusion ◽  
Atmospheric Conditions ◽  
Leak Test ◽  
High Temperature Side ◽  
Inconel 600

A heating element/electrical conduit assembly used in the Orbiter Maneuvering System failed a leak test during a routine refurbishment inspection. The conduit, approximately 100 mm in length and 12 mm in diameter, was fabricated from two tubes and braze-joined with a sleeve. The tube on the high temperature side (heating element side) and the sleeve were made of Inconel 600 and the other tube was stainless steel (SS) 316. For the filler metal, a Ni-Cr-B brazing alloy per AWS BNi-2, was used. A Helium leak test spotted the leak located at the joint between the sleeve and SS 316 tubing. This joint was dissected, mounted in a plastic mold, polished, and examined with an optical microscope. Debonding of the brazed surfaces was noticed, more pronounced toward the sleeve end which was exposed to uncontrolled atmospheric conditions intermittently. Initially, lack of wetting was suspected, presumably caused by inadequate surface preparation or incomplete fusion of the filler metal. However, this postulation was later discarded based upon the following observations: (1) The angle of wetting between the fillet and tube was small, an indication of adequate wetting, (2) the fillet did not exhibit a globular microstructure which would be an indication of insufficient melting of the filler metal, and (3) debonding was intermittent toward the midsection of the sleeve.

Effect of the Critical Angular Momentum on Incomplete Fusion Dynamics

2015 ◽  
Vol 3 (1) ◽  
pp. 13-17
Author(s):  
D. Singh ◽  
◽  
S. Bharti Linda ◽  
Pankaj Kumar Giri ◽  
H. Kumar ◽  
...  
Keyword(s):  
Angular Momentum ◽  
Incomplete Fusion ◽  
Critical Angular Momentum

Data Fusion Analysis For Test Validation System

2009 ◽  
Author(s):  
Mark H. Hammond ◽  
Christian Minor ◽  
Susan Rose-Pehrsson
Keyword(s):  
Data Fusion ◽  
Test Validation ◽  
Fusion Analysis

Novel Products in the CO2-Laser Induced Reaction of Trichloroethylene

1995 ◽  
Vol 60 (1) ◽  
pp. 104-114 ◽  
Author(s):  
Boyd L. Earl ◽  
Richard L. Titus
Keyword(s):  
Irradiation Time ◽  
Product Distribution ◽  
Incident Power ◽  
Cell Geometry ◽  
Reaction Conditions ◽  
Peak Areas ◽  
Induced Decomposition ◽  
Nmr Methods ◽  
Induced Reaction ◽  
Novel Products

Previous reports on the thermal or CO2-laser induced decomposition of trichloroethylene have identified only one condensible product, hexachlorobenzene (in addition to HCl and mono- and dichloroacetylene). We have found that trichloroethylene vapor exposed to cw irradiation on the P(24) line of the (001 - 100) band of the CO2 laser at incident power levels from 8 - 17 W produces numerous products, of which the 13 major ones have been identified using IR, GC/MS, GC/FTIR, and NMR methods. All of these products have 4, 6, or 8 carbons, are highly unsaturated, and are completely chlorinated or contain a single hydrogen. C4HCl5 and C6Cl6 isomers (three of each) account for S 55% to 85% of total products (based on peak areas in the total ion chromatograms in GC/MS runs), depending on reaction conditions. In addition to characterizing the products, we discuss the dependence of the product distribution on laser power, irradiation time, and cell geometry, and we outline a possible mechanism.

scholarly journals A New Type of Fusion Analysis Applicable to Many Organisms: Protein Fusions to the URA3 Gene of Yeast

Genetics ◽  
1987 ◽  
Vol 117 (1) ◽  
pp. 5-12
Author(s):  
Eric Alani ◽  
Nancy Kleckner
Keyword(s):  
Gene Fusion ◽  
Enzyme Assay ◽  
Decarboxylase Activity ◽  
Lacz Gene ◽  
Coding Region ◽  
Ura3 Gene ◽  
Promoter Sequences ◽  
E Coli ◽  
New Type ◽  
Fusion Analysis

ABSTRACT We have made constructs that join the promoter sequences and a portion of the coding region of the Saccharomyces cerevisiae HIS4 and GAL1 genes and the E. coli lacZ gene to the sixth codon of the S. cerevisiae URA3 gene (encodes orotidine-5′-phosphate (OMP) decarboxylase) to form three in frame protein fusions. In each case the fusion protein has OMP decarboxylase activity as assayed by complementation tests and this activity is properly regulated. A convenient cassette consisting of the URA3 segment plus some immediately proximal amino acids of HIS4C is available for making URA3 fusions to other proteins of interest. URA3 fusions offer several advantages over other systems for gene fusion analysis: the URA3 specified protein is small and cytosolic; genetic selections exist to identify mutants with either increased or decreased URA3 function in both yeast (S. cerevisiae and Schizosaccharomyces pombe) and bacteria (Escherichia coli and Salmonella typhimurium); and a sensitive OMP decarboxylase enzyme assay is available. Also, OMP decarboxylase activity is present in mammals, Drosophila and plants, so URA3 fusions may eventually be applicable in these other organisms as well.

scholarly journals Complete and incomplete fusion of Li7 projectiles on heavy targets

2020 ◽  
Vol 102 (6) ◽  
Author(s):  
M. R. Cortes ◽  
J. Rangel ◽  
J. L. Ferreira ◽  
J. Lubian ◽  
L. F. Canto
Keyword(s):  
Incomplete Fusion ◽  
Complete And Incomplete Fusion
Sign in / Sign up

Export Citation Format

Share Document