Study of a superconductor—normal-metal interface in a finite geometry

1978 ◽  
Vol 18 (7) ◽  
pp. 3174-3184 ◽  
Author(s):  
Ora Entin-Wohlman ◽  
J. Bar-Sagi
Keyword(s):  
Finite Geometry ◽  
Normal Metal ◽  
Metal Interface

Electrical resistivity of HTSC–normal metal interface

2013 ◽  
Vol 39 (2) ◽  
pp. 98-101 ◽  
Author(s):  
V. I. Sokolenko ◽  
V. A. Frolov
Keyword(s):  
Electrical Resistivity ◽  
Normal Metal ◽  
Metal Interface

Disentanglement of bulk and interfacial spin Hall effect in ferromagnet/normal metal interface

2016 ◽  
Vol 94 (14) ◽  
Author(s):  
X. Zhou ◽  
M. Tang ◽  
X. L. Fan ◽  
X. P. Qiu ◽  
S. M. Zhou
Keyword(s):  
Hall Effect ◽  
Spin Hall Effect ◽  
Normal Metal ◽  
Metal Interface

The oxidation of Inconel alloy MA754 at low oxidation potential

1983 ◽  
Vol 41 ◽  
pp. 218-219
Author(s):  
D. N. Braski ◽  
P. D. Goodell ◽  
J. V. Cathcart ◽  
R. H. Kane
Keyword(s):  
Surface Layer ◽  
Oxidation Potential ◽  
Metal Interface ◽  
Elevated Temperature Strength ◽  
Surface Conditions ◽  
Inconel Alloy ◽  
Inco Alloy ◽  
Resistance To Oxidation ◽  
Oxide Particles ◽  
Cold Worked

It has been known for some time that the addition of small oxide particles to an 80 Ni—20 Cr alloy not only increases its elevated-temperature strength, but also markedly improves its resistance to oxidation. The mechanism by which the oxide dispersoid enhances the oxidation resistance is being studied collaboratively by ORNL and INCO Alloy Products Company.Initial experiments were performed using INCONEL alloy MA754, which is nominally: 78 Ni, 20 Cr, 0.05 C, 0.3 Al, 0.5 Ti, 1.0 Fe, and 0.6 Y2O3 (wt %).Small disks (3 mm diam × 0.38 mm thick) were cut from MA754 plate stock and prepared with two different surface conditions. The first was prepared by mechanically polishing one side of a disk through 0.5 μm diamond on a syntron polisher while the second used an additional sulfuric acid-methanol electropolishing treatment to remove the cold-worked surface layer. Disks having both surface treatments were oxidized in a radiantly heated furnace for 30 s at 1000°C. Three different environments were investigated: hydrogen with nominal dew points of 0°C, —25°C, and —55°C. The oxide particles and films were examined in TEM by using extraction replicas (carbon) and by backpolishing to the oxide/metal interface. The particles were analyzed by EDS and SAD.

Preparation of cross-sectional samples for near-surface TEM studies

1987 ◽  
Vol 45 ◽  
pp. 380-381
Author(s):  
R.C. Dickenson ◽  
K.R. Lawless
Keyword(s):  
Standard Sample ◽  
Surface Region ◽  
Specimen Preparation ◽  
Thick Sheet ◽  
Drill Bit ◽  
Sample Holder ◽  
Metal Interface ◽  
Cross Sectional ◽  
Near Surface ◽  
Cold Worked

In thermal oxidation studies, the structure of the oxide-metal interface and the near-surface region is of great importance. A technique has been developed for constructing cross-sectional samples of oxidized aluminum alloys, which reveal these regions. The specimen preparation procedure is as follows: An ultra-sonic drill is used to cut a 3mm diameter disc from a 1.0mm thick sheet of the material. The disc is mounted on a brass block with low-melting wax, and a 1.0mm hole is drilled in the disc using a #60 drill bit. The drill is positioned so that the edge of the hole is tangent to the center of the disc (Fig. 1) . The disc is removed from the mount and cleaned with acetone to remove any traces of wax. To remove the cold-worked layer from the surface of the hole, the disc is placed in a standard sample holder for a Tenupol electropolisher so that the hole is in the center of the area to be polished.

Sign in / Sign up

Export Citation Format

Share Document