scholarly journals Endosomal explosion induced by hypertonicity enhances chitosan transfection

2019 ◽  
Author(s):  
Shupeng Wang ◽  
Shaohua Jin ◽  
Guangzhi Li ◽  
Rui Sun ◽  
Qinghai Shu ◽  
...  
Keyword(s):  
Cell Lines ◽  
Cell Function ◽  
Transfection Efficiency ◽  
Low Cost ◽  
Research Field ◽  
Gene Vector ◽  
Practical Strategy ◽  
Efficient Delivery ◽  
High Efficient ◽  
Short Time

AbstractTransferring DNA into cells to regulate cell function is a novel research field in recent decades. Chitosan is a gene vector with the properties of low-cost and safe, but high efficient delivery has remained challenging. We developed a strategy termed EEIH, for endosomal explosion induced by hypertonicity, in which short-time exposure to hypertonic solutions triggers endosomes destabilization like explosions. EEIH can force chitosan/DNA polyplexes to break through the endosomal barriers to approach the nucleus, which results in boosting the transfection efficiency of chitosan in several cell lines. We demonstrate that EEIH is a significant and practical strategy in chitosan transfection system without sophisticated modification of chitosan.

scholarly journals Gene delivery ability of polyethylenimine and polyethylene glycol dual-functionalized nanographene oxide in 11 different cell lines

2017 ◽  
Vol 4 (10) ◽  
pp. 170822 ◽  
Author(s):  
Liping Wu ◽  
Jinshan Xie ◽  
Tan Li ◽  
Zihao Mai ◽  
Lu Wang ◽  
...  
Keyword(s):  
Polyethylene Glycol ◽  
Gene Delivery ◽  
Cell Lines ◽  
High Efficiency ◽  
Articular Chondrocytes ◽  
Transfection Efficiency ◽  
H9c2 Cell ◽  
Hela Cell Lines ◽  
High Efficient ◽  
Plasmid Transfection

We recently developed a polyethylenimine (PEI) and polyethylene glycol (PEG) dual-functionalized reduced graphene oxide (GO) (PEG−nrGO−PEI, RGPP) for high-efficient gene delivery in HepG2 and Hela cell lines. To evaluate the feasibility and applicability of RGPP as a gene delivery carrier, we here assessed the transfection efficiency of RGPP on gene plasmids and siRNA in 11 different cell lines. Commercial polyalkyleneimine cation transfection reagent (TR) was used as comparison. In HepG2 cells, RGPP exhibited much stronger delivery ability for siRNA and large size plasmids than TR. For green fluorescent protein (GFP) plasmid, RGPP showed about 47.1% of transfection efficiency in primary rabbit articular chondrocytes, and about 27% of transfection efficiency in both SH-SY5Y and A549 cell lines. RGPP exhibited about 37.2% of GFP plasmid transfection efficiency in EMT6 cells and about 26.0% of GFP plasmid transfection efficiency in LO2 cells, but induced about 33% of cytotoxicity in both cell lines. In 4T1 and H9C2 cell lines, RGPP had less than 10% of GFP plasmid transfection efficiency. Collectively, RGPP is a potential nano-carrier for high-efficiency gene delivery, and needs to be further optimized for different cell lines.

Low-Cost Hardware Implementation of Human Blood Identification Device Using Feed-Forward Artificial Neural Network on FPGA

2018 ◽  
Author(s):  
Rizki Eka Putri ◽  
Denny Darlis
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Low Cost ◽  
Image Resolution ◽  
Blood Type ◽  
Feed Forward ◽  
Testing Facility ◽  
System Input ◽  
Artificial Neural ◽  
Short Time

This article was under review for ICELTICS 2018 -- In the medical world there is still service dissatisfaction caused by lack of blood type testing facility. If the number of tested blood arise, a lot of problems will occur so that electronic devices are needed to determine the blood type accurately and in short time. In this research we implemented an Artificial Neural Network on Xilinx Spartan 3S1000 Field Programable Gate Array using XSA-3S Board to identify the blood type. This research uses blood sample image as system input. VHSIC Hardware Discription Language is the language to describe the algorithm. The algorithm used is feed-forward propagation of backpropagation neural network. There are 3 layers used in design, they are input, hidden1, and output. At hidden1layer has two neurons. In this study the accuracy of detection obtained are 92%, 92%, 92%, 90% and 86% for 32x32, 48x48, 64x64, 80x80, and 96x96 pixel blood image resolution, respectively.

Robust Test Method of TSOP PEMs for Space Application

2019 ◽  
Author(s):  
Yasunobu Iwai ◽  
Koichi Shinozaki ◽  
Daiki Tanaka
Keyword(s):  
Evaluation Method ◽  
Low Cost ◽  
Reliability Evaluation ◽  
Test Method ◽  
Thermal Shock Test ◽  
Space Application ◽  
Space Applications ◽  
Limit Test ◽  
Long Time ◽  
Short Time

Abstract Compared with space parts, consumer parts are highly functional, low cost, compact and lightweight. Therefore, their increased usage in space applications is expected. Prior testing and evaluation on space applicability are necessary because consumer parts do not have quality guarantees for space application [1]. However, in the conventional reliability evaluation method, the test takes a long time, and the problem is that the robustness of the target sample can’t be evaluated in a short time. In this report, we apply to the latest TSOP PEM (Thin Small Outline Package Plastic Encapsulated Microcircuit) an evaluation method that combines preconditioning and HALT (Highly Accelerated Limit Test), which is a test method that causes failures in a short time under very severe environmental conditions. We show that this method can evaluate the robustness of TSOP PEMs including solder connections in a short time. In addition, the validity of this evaluation method for TSOP PEM is shown by comparing with the evaluation results of thermal shock test and life test, which are conventional reliability evaluation methods.

scholarly journals YB-1 Is Altered in Pregnancy-Associated Disorders and Affects Trophoblast in Vitro Properties via Alternation of Multiple Molecular Traits

2021 ◽  
Vol 22 (13) ◽  
pp. 7226
Author(s):  
Violeta Stojanovska ◽  
Aneri Shah ◽  
Katja Woidacki ◽  
Florence Fischer ◽  
Mario Bauer ◽  
...  
Keyword(s):  
Cell Lines ◽  
Cancer Progression ◽  
Cell Function ◽  
Trophoblast Cell ◽  
Mrna Levels ◽  
Trophoblast Cells ◽  
Invasion And Migration ◽  
And Migration ◽  
Apoptosis And Inflammation

Cold shock Y-box binding protein-1 (YB-1) coordinates several molecular processes between the nucleus and the cytoplasm and plays a crucial role in cell function. Moreover, it is involved in cancer progression, invasion, and metastasis. As trophoblast cells share similar characteristics with cancer cells, we hypothesized that YB-1 might also be necessary for trophoblast functionality. In samples of patients with intrauterine growth restriction, YB-1 mRNA levels were decreased, while they were increased in preeclampsia and unchanged in spontaneous abortions when compared to normal pregnant controls. Studies with overexpression and downregulation of YB-1 were performed to assess the key trophoblast processes in two trophoblast cell lines HTR8/SVneo and JEG3. Overexpression of YB-1 or exposure of trophoblast cells to recombinant YB-1 caused enhanced proliferation, while knockdown of YB-1 lead to proliferative disadvantage in JEG3 or HTR8/SVneo cells. The invasion and migration properties were affected at different degrees among the trophoblast cell lines. Trophoblast expression of genes mediating migration, invasion, apoptosis, and inflammation was altered upon YB-1 downregulation. Moreover, IL-6 secretion was excessively increased in HTR8/SVneo. Ultimately, YB-1 directly binds to NF-κB enhancer mark in HTR8/SVneo cells. Our data show that YB-1 protein is important for trophoblast cell functioning and, when downregulated, leads to trophoblast disadvantage that at least in part is mediated by NF-κB.

DEPOSITION OF SINGLE-PHASE CuInSe2 THIN FILMS UNDER LOW VACUUM LEVEL BY A TWO-STAGE GROWTH TECHNIQUE

2009 ◽  
Vol 16 (03) ◽  
pp. 381-386 ◽  
Author(s):  
J. B. CHU ◽  
H. B. ZHU ◽  
Z. A. WANG ◽  
Z. Q. BIAN ◽  
Z. SUN ◽  
...  
Keyword(s):  
Solar Cells ◽  
Single Phase ◽  
Low Cost ◽  
Control Process ◽  
Rf Magnetron Sputtering ◽  
Chalcopyrite Structure ◽  
Sputtering Deposition ◽  
Vacuum Level ◽  
X Ray ◽  
High Efficient

Single-phase CuInSe 2 films were grown by high vapor selenization of CuIn alloy precursors within a partially closed graphite box. The CuIn precursors were prepared using Cu x In y alloy targets with different composition rates under low vacuum level by a homemade sputtering system. The Cu and In composition rates of the used targets are 11:9, 10:10, and 9:11, respectively. The metallic precursor films were selenized using a two-step temperature profile, i.e. at 250°C and 400–500°C, respectively. The influence of the temperature at the second selenization step on the quality of the CIS absorbing layers was investigated. The CIS films were characterized by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis, and Raman spectroscopy. The deposited CIS absorbers selenized at a high temperature of 500°C for 30 min exhibited a single-phase chalcopyrite structure with a preferential orientation in the (112) direction. These layers display uniform, large, and densely packed crystals with a grain size of about 3–5 μm. Cadmium sulfide buffer layer was manufactured by chemical bath deposition method. Bilayers ZnO / ZnO : Al were prepared by RF magnetron sputtering deposition. CIS solar cells with an efficiency of about 6.5% were produced without antireflective films. The method to fabricate CIS solar cells by a combination of the low vacuum sputtering deposition and the graphite box selenization process has provided a simple control process and shown a promising potential for developing high efficient and low-cost CuInSe 2 solar cells.

scholarly journals Rapid Generation of Single-Tumor Spheroids for High-Throughput Cell Function and Toxicity Analysis

2006 ◽  
Vol 11 (8) ◽  
pp. 922-932 ◽  
Author(s):  
Andrea Ivascu ◽  
Manfred Kubbies
Keyword(s):  
Tumor Cell ◽  
Suspension Culture ◽  
Cell Lines ◽  
Cell Function ◽  
Tumor Cell Lines ◽  
Proliferating Cells ◽  
Basement Membrane Extract ◽  
Rapid Generation ◽  
Size Heterogeneity

Spheroids are widely used in biology because they provide an in vitro 3-dimensional (3D) model to study proliferation, cell death, differentiation, and metabolism of cells in tumors and the response of tumors to radiotherapy and chemotherapy. The methods of generating spheroids are limited by size heterogeneity, long cultivation time, or mechanical accessibility for higher throughput fashion. The authors present a rapid method to generate single spheroids in suspension culture in individual wells. A defined number of cells ranging from 1000 to 20,000 were seeded into wells of poly-HEMA-coated, 96-well, round-or conical-bottom plates in standard medium and centrifuged for 10 min at 1000 g. This procedure generates single spheroids in each well within a 24-h culture time with homogeneous sizes, morphologies, and stratification of proliferating cells in the rim and dying cells in the core region. Because a large number of tumor cell lines form only loose aggregates when cultured in 3D, the authors also performed a screen for medium additives to achieve a switch from aggregate to spheroid morphology. Small quantities of the basement membrane extract Matrigel, added to the culture medium prior to centrifugation, most effectively induced compact spheroid formation. The compact spheroid morphology is evident as early as 24 h after centrifugation in a true suspension culture. Twenty tumor cell lines of different lineages have been used to successfully generate compact, single spheroids with homogenous size in 96-well plates and are easily accessible for subsequent functional analysis.

scholarly journals Superior Antireflection Coating for a Silicon Cell with a Micronanohybrid Structure

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Hsi-Chien Liu ◽  
Gou-Jen Wang
Keyword(s):  
Solar Cell ◽  
Silicon Solar Cell ◽  
Low Cost ◽  
Antireflection Coating ◽  
Light Spectrum ◽  
Two Stage ◽  
Liquid Diffusion ◽  
Pyramid Structure ◽  
Short Time ◽  
Structure Array

The object of this paper is to develop a high antireflection silicon solar cell. A novel two-stage metal-assisted etching (MAE) method is proposed for the fabrication of an antireflective layer of a micronanohybrid structure array. The processing time for the etching on an N-type high-resistance (NH) silicon wafer can be controlled to around 5 min. The resulting micronanohybrid structure array can achieve an average reflectivity of 1.21% for a light spectrum of 200–1000 nm. A P-N junction on the fabricated micronanohybrid structure array is formed using a low-cost liquid diffusion source. A high antireflection silicon solar cell with an average efficiency of 13.1% can be achieved. Compared with a conventional pyramid structure solar cell, the shorted circuit current of the proposed solar cell is increased by 73%. The major advantage of the two-stage MAE process is that a high antireflective silicon substrate can be fabricated cost-effectively in a relatively short time. The proposed method is feasible for the mass production of low-cost solar cells.

scholarly journals Tracking the Evolution of Riverbed Morphology on the Basis of UAV Photogrammetry

2021 ◽  
Vol 13 (4) ◽  
pp. 829
Author(s):  
Teresa Gracchi ◽  
Guglielmo Rossi ◽  
Carlo Tacconi Stefanelli ◽  
Luca Tanteri ◽  
Rolando Pozzani ◽  
...  
Keyword(s):  
Management Practices ◽  
Low Cost ◽  
3D Models ◽  
Vegetation Coverage ◽  
Detection Analysis ◽  
Digital Terrain ◽  
Fluvial Dynamics ◽  
Aerial Vehicle ◽  
One Year ◽  
Short Time

Unmanned aerial vehicle (UAV) photogrammetry has recently become a widespread technique to investigate and monitor the evolution of different types of natural processes. Fluvial geomorphology is one of such fields of application where UAV potentially assumes a key role, since it allows for overcoming the intrinsic limits of satellite and airborne-based optical imagery on one side, and in situ traditional investigations on the other. The main purpose of this paper was to obtain extensive products (digital terrain models (DTMs), orthophotos, and 3D models) in a short time, with low costs and at a high resolution, in order to verify the capability of this technique to analyze the active geomorphic processes on a 12 km long stretch of the French–Italian Roia River at both large and small scales. Two surveys, one year apart from each other, were carried out over the study area and a change detection analysis was performed on the basis of the comparison of the obtained DTMs to point out and characterize both the possible morphologic variations related to fluvial dynamics and modifications in vegetation coverage. The results highlight how the understanding of different fluvial processes may be improved by appropriately exploiting UAV-based products, which can thus represent a low-cost and non-invasive tool to crucially support decisionmakers involved in land management practices.

Implementation of a Rig Test for Rotor/Stator Interaction of Low-Pressure Compressor Blades and Comparison of Experimental Results With Numerical Model

2020 ◽  
Author(s):  
Laura Pacyna ◽  
Alexandre Bertret ◽  
Alain Derclaye ◽  
Luc Papeleux ◽  
Jean-Philippe Ponthot
Keyword(s):  
Low Cost ◽  
Low Pressure ◽  
Angular Speed ◽  
Compressor Blades ◽  
Abradable Coating ◽  
Rotor Stator Interaction ◽  
Blade Tip ◽  
Numerical Tool ◽  
Short Time ◽  
Pressure Compressor

Abstract To investigate the contact phenomenon between the blade tip and the abradable coated casing, a rig test was designed and built. This rig test fills the following constraints: simplification of the low-pressure compressor environment but realistic mechanical conditions, ability to test several designs in short time, at low cost and repeatability. The rig test gives the opportunity to investigate the behavior of different blade designs regarding the sought phenomenon, to refine and mature the phenomenon comprehension and to get data for the numerical tool validation. The numerical tool considers a 3D finite elements model of low-pressure compressor blades with a surrounding rigid casing combined with a specialized model to take into account the effects of the wear of the abradable coating on the blade dynamics. Numerical results are in good agreement with tests in terms of: critical angular speed, blade dynamics and wear pattern on the abradable coated casing.

Sign in / Sign up

Export Citation Format

Share Document