scholarly journals Paperfuge: An ultra-low cost, hand-powered centrifuge inspired by the mechanics of a whirligig toy

2016 ◽  
Author(s):  
M. Saad Bhamla ◽  
Brandon Benson ◽  
Chew Chai ◽  
Georgios Katsikis ◽  
Aanchal Johri ◽  
...  
Keyword(s):  
Point Of Care ◽  
Low Cost ◽  
Centrifugal Forces ◽  
Operating Limits ◽  
3D Printed ◽  
Bottle Neck ◽  
Materials Used ◽  
Human Powered ◽  
Opening Up ◽  
Health Applications

AbstractSample preparation, including separation of plasma from whole blood or isolation of parasites, is an unmet challenge in many point of care (POC) diagnostics and requires centrifugation as the first key step. From the context of global health applications, commercial centrifuges are expensive, bulky and electricity-powered, leading to a critical bottle-neck in the development of decentralized, electricity-free POC diagnostic devices. By uncovering the fundamental mechanics of an ancient whirligig toy (3300 B.C.E), we design an ultra-low cost (20 cents), light-weight (2 g), human-powered centrifuge that is made out of paper (“paperfuge”). To push the operating limits of this unconventional centrifuge, we present an experimentally-validated theoretical model that describes the paperfuge as a non-linear, non-conservative oscillator system. We use this model to inform our design process, achieving speeds of 125,000 rpm and equivalent centrifugal forces of 30,000 g, with theoretical limits predicting one million rpm. We harness these speeds to separate pure plasma in less than 1.5 minutes and isolate malaria parasites in 15 minutes from whole human blood. By expanding the materials used, we implement centrifugal microfluidics using PDMS, plastic and 3D-printed devices, ultimately opening up new opportunities for electricity-free POC diagnostics, especially in resource-poor settings.

scholarly journals Negligible-cost microfluidic device fabrication using 3D-printed interconnecting channel scaffolds

PLoS ONE ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. e0245206
Author(s):  
Harry Felton ◽  
Robert Hughes ◽  
Andrea Diaz-Gaxiola
Keyword(s):  
Rapid Prototyping ◽  
Point Of Care ◽  
Low Cost ◽  
Microfluidic Channel ◽  
Microfluidic Devices ◽  
Device Fabrication ◽  
Appropriate Technology ◽  
Channel Cross Section ◽  
Microfluidic Systems ◽  
3D Printed

This paper reports a novel, negligible-cost and open-source process for the rapid prototyping of complex microfluidic devices in polydimethylsiloxane (PDMS) using 3D-printed interconnecting microchannel scaffolds. These single-extrusion scaffolds are designed with interconnecting ends and used to quickly configure complex microfluidic systems before being embedded in PDMS to produce an imprint of the microfluidic configuration. The scaffolds are printed using common Material Extrusion (MEX) 3D printers and the limits, cost & reliability of the process are evaluated. The limits of standard MEX 3D-printing with off-the-shelf printer modifications is shown to achieve a minimum channel cross-section of 100×100 μm. The paper also lays out a protocol for the rapid fabrication of low-cost microfluidic channel moulds from the thermoplastic 3D-printed scaffolds, allowing the manufacture of customisable microfluidic systems without specialist equipment. The morphology of the resulting PDMS microchannels fabricated with the method are characterised and, when applied directly to glass, without plasma surface treatment, are shown to efficiently operate within the typical working pressures of commercial microfluidic devices. The technique is further validated through the demonstration of 2 common microfluidic devices; a fluid-mixer demonstrating the effective interconnecting scaffold design, and a microsphere droplet generator. The minimal cost of manufacture means that a 5000-piece physical library of mix-and-match channel scaffolds (100 μm scale) can be printed for ~$0.50 and made available to researchers and educators who lack access to appropriate technology. This simple yet innovative approach dramatically lowers the threshold for research and education into microfluidics and will make possible the rapid prototyping of point-of-care lab-on-a-chip diagnostic technology that is truly affordable the world over.

scholarly journals CoreView: Fresh Tissue Biopsy Assessment at the Bedside Using a Millifluidic Imaging Chip

2021 ◽  
Author(s):  
David Cooper ◽  
Chuqin Huang ◽  
Dylan Klavins ◽  
Mark Fauver ◽  
Matthew Carson ◽  
...  
Keyword(s):  
Fluid Transport ◽  
Point Of Care ◽  
Low Cost ◽  
Breast Cancer Diagnosis ◽  
Fresh Tissue ◽  
Core Needle ◽  
Medical Diagnoses ◽  
Tissue Identification ◽  
3D Printed ◽  
Non Destructive

Minimally invasive core needle biopsies for medical diagnoses have become increasingly common for many diseases. Although tissue cores can yield more diagnostic information than fine needle biopsies and cytologic evaluation, there is no rapid evaluation at the point-of-care for intact tissue cores that is low-cost and non-destructive to the biopsy. We have developed a proof-of-concept 3D printed millifluidic histopathology lab-on-a-chip device to automatically handle, process, and image fresh core needle biopsies. This device, named CoreView, includes modules for biopsy removal from the acquisition tool, transport, staining and rinsing, imaging, segmentation, and multiplexed storage. Reliable removal from side-cutting needles and bidirectional fluid transport of core needle biopsies from five tissue types has been demonstrated with 0.5-mm positioning accuracy. Automation is aided by a MATLAB-based biopsy tracking algorithm that can detect the location of tissue and air bubbles in the channels of the millifluidic chip. With current and emerging optical imaging technologies, CoreView can be used for a rapid adequacy test at the point-of-care for tissue identification and glomeruli counting from renal core needle biopsies, and has the potential to be used for breast cancer diagnosis, phenotyping, and mapping of enriched tumorous regions for downstream analyses in global health applications.<br>

scholarly journals 3D Printed End of Arm Tooling (EOAT) for Robotic Automation

Robotics ◽  
2018 ◽  
Vol 7 (3) ◽  
pp. 49
Author(s):  
Daniel Ong U Jing ◽  
Declan Devine ◽  
John Lyons
Keyword(s):  
Lean Manufacturing ◽  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Filament Fabrication ◽  
3D Printed ◽  
Potential Weight ◽  
Materials Used ◽  
Strength And Stiffness ◽  
Flexural Tests ◽  
Robotic Automation

This research furthers the practice of designing and manufacturing End of Arm Tooling (EOAT) by utilizing a low cost additive manufacturing Fused Filament Fabrication (FFF) technique to enable tool weight saving and provision of low cost EOATs on demand, thereby facilitating zero inventory lean manufacturing. The materials used in this research for the fabrication of the EOAT parts were Acrylonitrile butadiene styrene (ABS) and nylon with infill densities of 20% and 100%. Three-point flexural tests were performed to determine the differences in strength and stiffness between varying polymers, infill ratios, and a standard metal part. Additionally, potential weight savings were identified and challenges with utilizing low cost FFF technologies are outlined. A motion of programmed trajectories was executed utilizing a standard 6-axis robot and the power consumption was evaluated. This study demonstrates the utility of using thermoplastic material with the fabrication of 3D printed parts used in EOATs.

scholarly journals 3D-Printed Immunosensor Arrays for Cancer Diagnostics

Sensors ◽  
2020 ◽  
Vol 20 (16) ◽  
pp. 4514 ◽  
Author(s):  
Mohamed Sharafeldin ◽  
Karteek Kadimisetty ◽  
Ketki S. Bhalerao ◽  
Tianqi Chen ◽  
James F. Rusling
Keyword(s):  
3D Printing ◽  
Early Stage ◽  
Point Of Care ◽  
Low Cost ◽  
Cancer Diagnostics ◽  
Diagnostic Tools ◽  
Protein Biomarkers ◽  
Protein Biomarker ◽  
Subtractive Manufacturing ◽  
3D Printed

Detecting cancer at an early stage of disease progression promises better treatment outcomes and longer lifespans for cancer survivors. Research has been directed towards the development of accessible and highly sensitive cancer diagnostic tools, many of which rely on protein biomarkers and biomarker panels which are overexpressed in body fluids and associated with different types of cancer. Protein biomarker detection for point-of-care (POC) use requires the development of sensitive, noninvasive liquid biopsy cancer diagnostics that overcome the limitations and low sensitivities associated with current dependence upon imaging and invasive biopsies. Among many endeavors to produce user-friendly, semi-automated, and sensitive protein biomarker sensors, 3D printing is rapidly becoming an important contemporary tool for achieving these goals. Supported by the widely available selection of affordable desktop 3D printers and diverse printing options, 3D printing is becoming a standard tool for developing low-cost immunosensors that can also be used to make final commercial products. In the last few years, 3D printing platforms have been used to produce complex sensor devices with high resolution, tailored towards researchers’ and clinicians’ needs and limited only by their imagination. Unlike traditional subtractive manufacturing, 3D printing, also known as additive manufacturing, has drastically reduced the time of sensor and sensor array development while offering excellent sensitivity at a fraction of the cost of conventional technologies such as photolithography. In this review, we offer a comprehensive description of 3D printing techniques commonly used to develop immunosensors, arrays, and microfluidic arrays. In addition, recent applications utilizing 3D printing in immunosensors integrated with different signal transduction strategies are described. These applications include electrochemical, chemiluminescent (CL), and electrochemiluminescent (ECL) 3D-printed immunosensors. Finally, we discuss current challenges and limitations associated with available 3D printing technology and future directions of this field.

scholarly journals A Portable 3D-Printed Platform for Point-of-Care Diagnosis of Clostridium Difficile Infection and Malaria

2019 ◽  
Author(s):  
Soichiro Tsuda ◽  
Lewis A. Fraser ◽  
Salah Sharabi ◽  
Mohammed Hezwani ◽  
Andrew Kinghorn ◽  
...  
Keyword(s):  
Clostridium Difficile ◽  
3D Printing ◽  
Open Source ◽  
Clostridium Difficile Infection ◽  
Point Of Care ◽  
Low Cost ◽  
Clinical Applications ◽  
Printing Technology ◽  
3D Printing Technology ◽  
3D Printed

Here, we integrate 3D-printing technology with low-cost open source electronics to develop a portable diagnostic platform suitable for a wide variety of diagnostic and sensing assays. We demonstrate two different clinical applications in the diagnosis of <i>Clostridium difficile</i> infection and malaria.

scholarly journals A Portable 3D-Printed Platform for Point-of-Care Diagnosis of Clostridium Difficile Infection and Malaria

2019 ◽  
Author(s):  
Soichiro Tsuda ◽  
Lewis A. Fraser ◽  
Salah Sharabi ◽  
Mohammed Hezwani ◽  
Andrew Kinghorn ◽  
...  
Keyword(s):  
Clostridium Difficile ◽  
3D Printing ◽  
Open Source ◽  
Clostridium Difficile Infection ◽  
Point Of Care ◽  
Low Cost ◽  
Clinical Applications ◽  
Printing Technology ◽  
3D Printing Technology ◽  
3D Printed

Here, we integrate 3D-printing technology with low-cost open source electronics to develop a portable diagnostic platform suitable for a wide variety of diagnostic and sensing assays. We demonstrate two different clinical applications in the diagnosis of <i>Clostridium difficile</i> infection and malaria.

scholarly journals In-Hospital 3D Printed Scaphoid Prosthesis Using Medical-Grade Polyetheretherketone (PEEK) Biomaterial

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Philipp Honigmann ◽  
Neha Sharma ◽  
Ralf Schumacher ◽  
Jasmine Rueegg ◽  
Mathias Haefeli ◽  
...  
Keyword(s):  
3D Printing ◽  
Point Of Care ◽  
Low Cost ◽  
Three Dimensional ◽  
Patient Specific ◽  
Fused Filament Fabrication ◽  
Patient Specific Implants ◽  
Surgical Guides ◽  
3D Printed ◽  
Medical Grade

Recently, three-dimensional (3D) printing has become increasingly popular in the medical sector for the production of anatomical biomodels, surgical guides, and prosthetics. With the availability of low-cost desktop 3D printers and affordable materials, the in-house or point-of-care manufacturing of biomodels and Class II medical devices has gained considerable attention in personalized medicine. Another projected development in medical 3D printing for personalized treatment is the in-house production of patient-specific implants (PSIs) for partial and total bone replacements made of medical-grade material such as polyetheretherketone (PEEK). We present the first in-hospital 3D printed scaphoid prosthesis using medical-grade PEEK with fused filament fabrication (FFF) 3D printing technology.

scholarly journals CoreView: Fresh Tissue Biopsy Assessment at the Bedside Using a Millifluidic Imaging Chip

2021 ◽  
Author(s):  
David Cooper ◽  
Chuqin Huang ◽  
Dylan Klavins ◽  
Mark Fauver ◽  
Matthew Carson ◽  
...  
Keyword(s):  
Fluid Transport ◽  
Point Of Care ◽  
Low Cost ◽  
Breast Cancer Diagnosis ◽  
Fresh Tissue ◽  
Core Needle ◽  
Medical Diagnoses ◽  
Tissue Identification ◽  
3D Printed ◽  
Non Destructive

Minimally invasive core needle biopsies for medical diagnoses have become increasingly common for many diseases. Although tissue cores can yield more diagnostic information than fine needle biopsies and cytologic evaluation, there is no rapid evaluation at the point-of-care for intact tissue cores that is low-cost and non-destructive to the biopsy. We have developed a proof-of-concept 3D printed millifluidic histopathology lab-on-a-chip device to automatically handle, process, and image fresh core needle biopsies. This device, named CoreView, includes modules for biopsy removal from the acquisition tool, transport, staining and rinsing, imaging, segmentation, and multiplexed storage. Reliable removal from side-cutting needles and bidirectional fluid transport of core needle biopsies from five tissue types has been demonstrated with 0.5-mm positioning accuracy. Automation is aided by a MATLAB-based biopsy tracking algorithm that can detect the location of tissue and air bubbles in the channels of the millifluidic chip. With current and emerging optical imaging technologies, CoreView can be used for a rapid adequacy test at the point-of-care for tissue identification and glomeruli counting from renal core needle biopsies, and has the potential to be used for breast cancer diagnosis, phenotyping, and mapping of enriched tumorous regions for downstream analyses in global health applications.<br>

Design and evaluation of a novel and sustainable human-powered low-cost 3D printed thermal laryngoscope

2019 ◽  
Vol 43 (5) ◽  
Author(s):  
Michael Dinsmore ◽  
Sachin Doshi ◽  
Vivian Sin ◽  
Clyde Matava
Keyword(s):  
Low Cost ◽  
3D Printed ◽  
Human Powered

Opening up a New Field of Modern Medical Research 1

2020 ◽  
Author(s):  
Xiaoguang Li
Keyword(s):  
Chinese Medicine ◽  
Traditional Chinese Medicine ◽  
Human Body ◽  
Low Cost ◽  
Acupuncture Point ◽  
Modern Medicine ◽  
Body Structure ◽  
Special Effect ◽  
Special Knowledge ◽  
Opening Up

Modern medicine tells us that the human body is an organism composed of heart, lung, liver, kidney, spleen, stomach, brain, nerves, muscles, bones, blood vessels, blood and so on, while traditional Chinese medicine believes that besides these tissues and organs, the human body still has another part of the structure, traditional Chinese medicine calls them Jing Luo and Shu Xue. Jing Luo means the longitudinal line of the human body and the accompanying net, translated into English Meridians and Collaterals. Shu Xue means holes distributed on Jing Luo and outside Jing Luo, because stimulating Shu Xue's position by acupuncture, massage and other methods can cure diseases, so Shu Xue is translated into English acupuncture point, abbreviated as acupoint or point. Meridians and acupoints are the special knowledge of human body structure in traditional Chinese medicine. Traditional Chinese medicine not only draws the distribution map of the meridians and acupoints in the human body, but also has been using them to treat diseases for thousands of years. There are hundreds of these acupoints, stimulating each one by acupuncture, massage or other methods will have a special effect on the human body and can treat various diseases. But what effect does stimulating every acupoint have on the human body so that it can treat various diseases? The discussion of traditional Chinese medicine is vague and incomprehensible, and can not be proved by experiments. According to the author's research for more than 30 years, this paper makes a clear and accurate exposition of the effects on the human body and diseases that can be treated with acupoint massage. These statements can be proved by experiments, so they are believed to be reliable. It is hoped that meridians, acupoints and massage therapy can be incorporated into modern medicine and become a part of modern medicine after being proved by others through experiments. Massaging acupoints can not only treat many diseases that are difficult to be treated with drugs, but also have simple methods and low cost.

Sign in / Sign up

Export Citation Format

Share Document