scholarly journals Splash-cup plants accelerate raindrops to disperse seeds

2013 ◽  
Vol 10 (79) ◽  
pp. 20120880 ◽  
Author(s):  
Guillermo J. Amador ◽  
Yasukuni Yamada ◽  
Matthew McCurley ◽  
David L. Hu
Keyword(s):  
High Speed ◽  
Cone Angle ◽  
Three Dimensional ◽  
Dispersal Distance ◽  
Optimal Angle ◽  
Three Dimensional Printing ◽  
A Value ◽  
Dispersal Distances ◽  
Drop Impacts ◽  
Dimensional Printing

The conical flowers of splash-cup plants Chrysosplenium and Mazus catch raindrops opportunistically, exploiting the subsequent splash to disperse their seeds. In this combined experimental and theoretical study, we elucidate their mechanism for maximizing dispersal distance. We fabricate conical plant mimics using three-dimensional printing, and use high-speed video to visualize splash profiles and seed travel distance. Drop impacts that strike the cup off-centre achieve the largest dispersal distances of up to 1 m. Such distances are achieved because splash speeds are three to five times faster than incoming drop speeds, and so faster than the traditionally studied splashes occurring upon horizontal surfaces. This anomalous splash speed is because of the superposition of two components of momentum, one associated with a component of the drop's motion parallel to the splash-cup surface, and the other associated with film spreading induced by impact with the splash-cup. Our model incorporating these effects predicts the observed dispersal distance within 6–18% error. According to our experiments, the optimal cone angle for the splash-cup is 40°, a value consistent with the average of five species of splash-cup plants. This optimal angle arises from the competing effects of velocity amplification and projectile launching angle.

scholarly journals Laser-induced forward transfer of viscoplastic fluids

2019 ◽  
Vol 880 ◽  
pp. 497-513 ◽  
Author(s):  
Maziyar Jalaal ◽  
Martin Klein Schaarsberg ◽  
Claas-Willem Visser ◽  
Detlef Lohse
Keyword(s):  
High Speed ◽  
Laser Energy ◽  
Three Dimensional ◽  
Liquid Jet ◽  
Control Parameters ◽  
Optimal Conditions ◽  
High Speed Imaging ◽  
Three Dimensional Printing ◽  
Forward Transfer ◽  
Dimensional Printing

Laser-induced forward transfer (LIFT) is a nozzle-free printing technology that can be used for two- and three-dimensional printing. In LIFT, a laser pulse creates an impulse inside a thin film of material that results in the formation of a liquid jet. We experimentally study LIFT of viscoplastic materials by visualizing the process of jetting with high-speed imaging. The shape of the jet depends on the laser energy, focal height, surface tension and material rheology. We theoretically identify the characteristic jetting velocity and how it depends on the control parameters, and define non-dimensional groups to classify the regimes of jetting. Based on the results, we propose the optimal conditions for printing with LIFT technology.

scholarly journals Rebound of self-lubricating compound drops

2020 ◽  
Vol 6 (11) ◽  
pp. eaay3499 ◽  
Author(s):  
Nathan Blanken ◽  
Muhammad Saeed Saleem ◽  
Carlo Antonini ◽  
Marie-Jean Thoraval
Keyword(s):  
Solid Surface ◽  
High Speed ◽  
Water Drop ◽  
Three Dimensional ◽  
Strong Impact ◽  
High Speed Imaging ◽  
Three Dimensional Printing ◽  
Compound Drops ◽  
The Impact ◽  
Dimensional Printing

Drop impact on solid surfaces is encountered in numerous natural and technological processes. Although the impact of single-phase drops has been widely explored, the impact of compound drops has received little attention. Here, we demonstrate a self-lubrication mechanism for water-in-oil compound drops impacting on a solid surface. Unexpectedly, the core water drop rebounds from the surface below a threshold impact velocity, irrespective of the substrate wettability. This is interpreted as the result of lubrication from the oil shell that prevents contact between the water core and the solid surface. We combine side and bottom view high-speed imaging to demonstrate the correlation between the water core rebound and the oil layer stability. A theoretical model is developed to explain the observed effect of compound drop geometry. This work sets the ground for precise complex drop deposition, with a strong impact on two- and three-dimensional printing technologies and liquid separation.

scholarly journals Study of Layer Formation During Droplet-Based Three-Dimensional Printing of Gel Structures

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
Kyle Christensen ◽  
Yong Huang
Keyword(s):  
Inkjet Printing ◽  
High Speed ◽  
Three Dimensional ◽  
Layer By Layer ◽  
Layer Formation ◽  
High Speed Imaging ◽  
Three Dimensional Printing ◽  
Drop On Demand ◽  
Image Velocimetry ◽  
Dimensional Printing

Additive manufacturing, also known as three-dimensional (3D) printing, is an approach in which a structure may be fabricated layer by layer. For 3D inkjet printing, droplets are ejected from a nozzle, and each layer is formed droplet by droplet. Inkjet printing has been widely applied for the fabrication of 3D biological gel structures, but the knowledge of the microscale interactions between printed droplets is still largely elusive. This study aims to elucidate the layer formation mechanism in terms of the formation of single lines and layers comprised of adjacent lines during drop-on-demand inkjet printing of alginate using high speed imaging and particle image velocimetry. Inkjet droplets are found to impact, spread, and coalesce within a fluid region at the deposition site, forming coherent printed lines within a layer. The effects of printing conditions on the behavior of droplets during layer formation are discussed and modeled based on gelation dynamics, and recommendations are presented to enable controllable and reliable fabrication of gel structures. The effects of gelation on droplet impact dynamics are found to be negligible during alginate printing, and interfaces are found to form between printed lines within a layer depending on printing conditions, printing path orientation, and gelation dynamics.

scholarly journals Exploring the Optimal Design for and Experimentation on a Bowl-Based Mechanism for Transplanting Potted Strawberry Seedlings

2021 ◽  
Author(s):  
Yin Daqing ◽  
Yang Yuchao ◽  
Zhou Maile ◽  
Wei Mingxu ◽  
Wang Jinwu
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
High Speed Photography ◽  
Simulation Design ◽  
Three Dimensional Model ◽  
Three Dimensional Printing ◽  
New Device ◽  
Working Principle ◽  
Dimensional Printing ◽  
Actual Trajectory

Abstract To improve the mechanization of strawberry planting integration and the efficiency of fetching and transplanting seedlings, an integrated transplanting mechanism with protruding, fetching and planting is designed. This new device can realize rapid fetching and pushing bowl movements. The working principle of the slewing mechanism is analyzed, a kinematics model of the mechanism is established, and the optimization goal is established. Visual auxiliary analysis software is developed, optimized parameters are established, and the corresponding theoretical trajectory is provided. A three-dimensional model is established and a virtual simulation design analysis is performed to obtain a simulation trajectory. Three-dimensional printing technology is used to manufacture the test prototype, and the actual working trajectory of the test prototype is extracted using high-speed photography technology, which verifies the consistency of the actual trajectory with the theoretical and simulated trajectories. A prototype transplanting experiment is performed, showing that the success rate of seedling extraction is 91.2% and the rate of excellent planting is 82.8%, which meet the requirements for integrated strawberry harvesting, planting and transplanting and verify the correctness and feasibility of the mechanism design.

A novel fast disintegrating tablet fabricated by three‐dimensional printing

2009 ◽  
Vol 00 (00) ◽  
pp. 090730035508060-7
Author(s):  
Deng-Guang Yu ◽  
Chris Branford-White ◽  
Yi-Cheng Yang ◽  
Li-Min Zhu ◽  
Edward William Welbeck ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Fast Disintegrating Tablet ◽  
Dimensional Printing

Central ossifying fibroma of mandible

2020 ◽  
Vol 13 (12) ◽  
pp. e239286
Author(s):  
Kumar Nilesh ◽  
Prashant Punde ◽  
Nitin Shivajirao Patil ◽  
Amol Gautam
Keyword(s):  
Fibrous Tissue ◽  
Three Dimensional ◽  
Facial Asymmetry ◽  
Ossifying Fibroma ◽  
Mandible Reconstruction ◽  
Three Dimensional Printing ◽  
Osseous Lesion ◽  
Large Size ◽  
Dimensional Printing

Ossifying fibroma (OF) is a rare, benign, fibro-osseous lesion of the jawbone characterised by replacement of the normal bone with fibrous tissue. The fibrous tissue shows varying amount of calcified structures resembling bone and/or cementum. The central variant of OF is rare, and shows predilection for mandible among the jawbone. Although it is classified as fibro-osseous lesion, it clinically behaves as a benign tumour and can grow to large size, causing bony swelling and facial asymmetry. This paper reports a case of large central OF of mandible in a 40-year-old male patient. The lesion was treated by segmental resection of mandible. Reconstruction of the surgical defect was done using avascular fibula bone graft. Role of three-dimensional printing of jaw and its benefits in surgical planning and reconstruction are also highlighted.

scholarly journals Three-Dimensional Printing in Orthopedics: from the Basics to Surgical Applications

2021 ◽  
Author(s):  
Leandro Ejnisman ◽  
Bruno Gobbato ◽  
Andre Ferrari de França Camargo ◽  
Eduardo Zancul
Keyword(s):  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Dimensional Printing
Sign in / Sign up

Export Citation Format

Share Document