A two-dimensional axisymmetric flow model for the analysis of pulsed detonation thermal spraying

2003 ◽  
Vol 175 (9) ◽  
pp. 1649-1677 ◽  
Author(s):  
K. Ramadan ◽  
P. Barry Butler
Keyword(s):  
Flow Model ◽  
Axisymmetric Flow ◽  
Thermal Spraying ◽  
Two Dimensional ◽  
Pulsed Detonation

scholarly journals Nozzle Shape Optimization for an MPD Thruster Using a Two-Dimensional Axisymmetric Flow Model

2011 ◽  
Vol 59 (687) ◽  
pp. 90-96 ◽  
Author(s):  
Masakatsu NAKANE ◽  
Masao NAGAO ◽  
Yoshio ISHIKAWA ◽  
Kenichi KUBOTA ◽  
Ikkou FUNAKI
Keyword(s):  
Shape Optimization ◽  
Flow Model ◽  
Axisymmetric Flow ◽  
Two Dimensional ◽  
Nozzle Shape

An Evaluation of the Average Flow Model [1] for Surface Roughness Effects in Lubrication

1980 ◽  
Vol 102 (3) ◽  
pp. 360-366 ◽  
Author(s):  
J. L. Teale ◽  
A. O. Lebeck
Keyword(s):  
Surface Roughness ◽  
Flow Model ◽  
Two Dimensional ◽  
Roughness Effects ◽  
Important Conclusion ◽  
Average Flow ◽  
One Dimensional ◽  
Dimensional Flow ◽  
Two Dimensional Flow ◽  
Average Flow Model

The average flow model presented by Patir and Cheng [1] is evaluated. First, it is shown that the choice of grid used in the average flow model influences the results. The results presented are different from those given by Patir and Cheng. Second, it is shown that the introduction of two-dimensional flow greatly reduces the effect of roughness on flow. Results based on one-dimensional flow cannot be relied upon for two-dimensional problems. Finally, some average flow factors are given for truncated rough surfaces. These can be applied to partially worn surfaces. The most important conclusion reached is that an even closer examination of the average flow concept is needed before the results can be applied with confidence to lubrication problems.

Measurement of Recovery Factors and Friction Coefficients for Supersonic Flow of Air in a Tube: 2—Results Based on a Two-Dimensional Flow Model for Entrance Region

1952 ◽  
Vol 19 (2) ◽  
pp. 185-194
Author(s):  
J. Kaye ◽  
T. Y. Toong ◽  
R. H. Shoulberg
Keyword(s):  
Boundary Layer ◽  
Supersonic Flow ◽  
Laminar Boundary Layer ◽  
Flow Model ◽  
Variable Mass ◽  
Entrance Region ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Change Of State ◽  
Two Dimensional Flow

Abstract The first part of a program to obtain reliable data on the rate of heat transfer to air moving at supersonic speeds in a tube has been devoted to measurements made on adiabatic supersonic flow of air in a tube. The details of these measurements have been described in a previous paper. The calculated quantities such as the local apparent friction coefficient, recovery factor, Mach number, and so forth, were obtained from the simple one-dimensional flow model for which the properties of the stream are uniform at any section, and boundary-layer effects are ignored. The analysis of some of the same data given in the previous paper is undertaken here with the aid of a simplified two-dimensional flow model. The supersonic flow in the tube is divided into a supersonic core of variable mass with the fluid remaining in the core undergoing a reversible adiabatic change of state, and a laminar boundary layer of variable mass. The compressible laminar boundary layer increases in thickness in the direction of flow, and then undergoes a transition to a turbulent boundary layer. The two-dimensional flow model is limited here to the region where a laminar boundary layer appears to be present in the entrance region of the tube. The results of the analysis based on the two-dimensional flow model indicate that where the flow in the tube boundary layer appears to be laminar, the measured pressures and temperatures in the tube for adiabatic supersonic flow of air could have been predicted, with sufficient accuracy for engineering problems, from measured data for supersonic flow of air over a flat plate with a laminar boundary layer, and with zero pressure gradient.

A Two-Dimensional Potential Flow Model of the Wave Field Generated by a Semisubmerged Body in Heaving Motion

1988 ◽  
Vol 32 (02) ◽  
pp. 83-91
Author(s):  
X. M. Wang ◽  
M. L. Spaulding
Keyword(s):  
Free Surface ◽  
Boundary Conditions ◽  
Potential Flow ◽  
Flow Model ◽  
Second Order ◽  
Two Dimensional ◽  
Third Order ◽  
The Third ◽  
Potential Flow Model ◽  
Good Agreement

A two-dimensional potential flow model is formulated to predict the wave field and forces generated by a sere!submerged body in forced heaving motion. The potential flow problem is solved on a boundary fitted coordinate system that deforms in response to the motion of the free surface and the heaving body. The full nonlinear kinematic and dynamic boundary conditions are used at the free surface. The governing equations and associated boundary conditions are solved by a second-order finite-difference technique based on the modified Euler method for the time domain and a successive overrelaxation (SOR) procedure for the spatial domain. A series of sensitivity studies of grid size and resolution, time step, free surface and body grid redistribution schemes, convergence criteria, and free surface body boundary condition specification was performed to investigate the computational characteristics of the model. The model was applied to predict the forces generated by the forced oscillation of a U-shaped cylinder. Numerical model predictions are generally in good agreement with the available second-order theories for the first-order pressure and force coefficients, but clearly show that the third-order terms are larger than the second-order terms when nonlinearity becomes important in the dimensionless frequency range 1≤ Fr≤ 2. The model results are in good agreement with the available experimental data and confirm the importance of the third order terms.

Sign in / Sign up

Export Citation Format

Share Document