scholarly journals Noise emitted from a generic side-view mirror with different aspect ratios and inclinations

2021 ◽  
Vol 33 (8) ◽  
pp. 084105
Author(s):  
K. K. Chode ◽  
H. Viswanathan ◽  
K. Chow
Keyword(s):  
Side View ◽  
Aspect Ratios

Radial mass analysis of unstained STEM images of molluscan hemocyanins

1990 ◽  
Vol 48 (3) ◽  
pp. 810-811
Author(s):  
M.G. Hamilton ◽  
T.T. Herskovits ◽  
J.S. Wall
Keyword(s):  
Image Analysis ◽  
Hollow Cylinder ◽  
Electron Micrographs ◽  
Side View ◽  
Mass Analysis ◽  
Mass Measurements ◽  
Electron Microscopic ◽  
Transmission Electron ◽  
Transmission Electron Microscopic ◽  
Microscopic Studies

The hemocyanins of molluscs are aggregates of a cylindrical decameric subparticle that assembles into di-, tri-, tetra-, penta-, and larger multi-decameric particles with masses that are multiples of the 4.4 Md decamer. Electron micrographs of these hemocyanins typically show the particles with two profiles: circular representing the cylinder viewed from the end and rectangular representing the side-view of the hollow cylinder.The model proposed by Mellema and Klug from image analysis of a didecameric hemocyanin with the two decamers facing one another with collar (closed) ends outward fits the appearance of side-views of the negatively-stained cylinders. These authors also suggested that there might be caps at the ends. In one of a series of transmission electron microscopic studies of molluscan hemocyanins, Siezen and Van Bruggen supported the Mellema-Klug model, but stated that they had never observed a cap component. With STEM we have tested the end cap hypothesis by direct mass measurements across the end-views of unstained particles.

Tire Treadwear — A Comprehensive Evaluation of the Factors: Generic Type, Aspect Ratio, Tread Pattern, and Tread Composition Part III: Results of Supplementary and UTQG Treadwear Test Series

1986 ◽  
Vol 14 (4) ◽  
pp. 235-263
Author(s):  
A. G. Veith
Keyword(s):  
Carbon Black ◽  
Comprehensive Evaluation ◽  
Work Intensity ◽  
Generic Type ◽  
Aspect Ratios ◽  
Index Variation ◽  
Primary Determinant ◽  
Severity Levels ◽  
High Test ◽  
Better Than

Abstract The effect of tread compound variation on tire treadwear was studied using bias and radial tires of two aspect ratios. Compound variations included types of rubber and carbon black as well as the levels of carbon black, process oil, and curatives. At low to moderate test severity, SBR and an SBR/BR blend performed better than NR while at high test severity NR and SBR were better than the SBR/BR blend. The SBR/BR blend was the best at low severity testing. Higher structure and higher surface area carbon black gave improved treadwear at all severity levels. The concept of a “frictional work intensity” as the primary determinant of treadwear index variation with test severity is proposed. Some factors which influence frictional work intensity are discussed.

Advanced Fringe Analysis Techniques in Circuit Edit

2006 ◽  
Author(s):  
R.K. Jain ◽  
T. Malik ◽  
T.R. Lundquist ◽  
C.-C. Tsao ◽  
W.J. Walecki
Keyword(s):  
Imaging System ◽  
Success Rates ◽  
Endpoint Detection ◽  
Fringe Analysis ◽  
Analysis Techniques ◽  
Aspect Ratios ◽  
Slope Correction ◽  
Trench Area ◽  
And Control ◽  
Thickness Measurements

Abstract Novel Fabry Perot [1] fringe analysis techniques for monitoring the etching process with a coaxial photon-ion column [2] in the Credence OptiFIB are reported. Presently the primary application of these techniques in circuit edit is in trenching either from the front side or from the backside of a device. Optical fringes are observed in reflection geometry through the imaging system when the trench floor is thin and semi-transparent. The observed fringes result from optical interference in the etalon formed between the trench floor (Si in the case of backside trenching) and the circuitry layer beyond the trench floor. In-situ real-time thickness measurements and slope correction techniques are proposed that improve endpoint detection and control planarity of the trench floor. For successful through silicon edits, reliable endpoint detection and co-planarity of a local trench is important. Reliable endpoint detection prevents milling through bulk silicon and damaging active circuitry. Uneven trench floor thickness results in premature endpoint detection with sufficient thickness remaining in only part of the trench area. Good co-planarity of the trench floor also minimizes variability in the aspect ratios of the edit holes, hence increasing success rates in circuit edit.

scholarly journals Differential Sorting of Microparticles Using Spiral Microchannels with Elliptic Configurations

Micromachines ◽  
2020 ◽  
Vol 11 (4) ◽  
pp. 412
Author(s):  
Kaan Erdem ◽  
Vahid Ebrahimpour Ahmadi ◽  
Ali Kosar ◽  
Lütfullah Kuddusi
Keyword(s):  
Cell Sorting ◽  
Microfluidic Channel ◽  
Major Axis ◽  
Label Free ◽  
Flow Rates ◽  
Inertial Focusing ◽  
Size Dependent ◽  
Curved Channels ◽  
Aspect Ratios ◽  
Dependent Cell

Label-free, size-dependent cell-sorting applications based on inertial focusing phenomena have attracted much interest during the last decade. The separation capability heavily depends on the precision of microparticle focusing. In this study, five-loop spiral microchannels with a height of 90 µm and a width of 500 µm are introduced. Unlike their original spiral counterparts, these channels have elliptic configurations of varying initial aspect ratios, namely major axis to minor axis ratios of 3:2, 11:9, 9:11, and 2:3. Accordingly, the curvature of these configurations increases in a curvilinear manner through the channel. The effects of the alternating curvature and channel Reynolds number on the focusing of fluorescent microparticles with sizes of 10 and 20 µm in the prepared suspensions were investigated. At volumetric flow rates between 0.5 and 3.5 mL/min (allowing separation), each channel was tested to collect samples at the designated outlets. Then, these samples were analyzed by counting the particles. These curved channels were capable of separating 20 and 10 µm particles with total yields up to approximately 95% and 90%, respectively. The results exhibited that the level of enrichment and the focusing behavior of the proposed configurations are promising compared to the existing microfluidic channel configurations.

scholarly journals Assessing Machine Learning versus a Mathematical Model to Estimate the Transverse Shear Stress Distribution in a Rectangular Channel

Mathematics ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 596
Author(s):  
Babak Lashkar-Ara ◽  
Niloofar Kalantari ◽  
Zohreh Sheikh Khozani ◽  
Amir Mosavi
Keyword(s):  
Shear Stress ◽  
Stress Distribution ◽  
Fuzzy Inference ◽  
Rectangular Channel ◽  
Tsallis Entropy ◽  
Shear Stress Distribution ◽  
Data Series ◽  
Shear Stresses ◽  
Inference System ◽  
Aspect Ratios

One of the most important subjects of hydraulic engineering is the reliable estimation of the transverse distribution in the rectangular channel of bed and wall shear stresses. This study makes use of the Tsallis entropy, genetic programming (GP) and adaptive neuro-fuzzy inference system (ANFIS) methods to assess the shear stress distribution (SSD) in the rectangular channel. To evaluate the results of the Tsallis entropy, GP and ANFIS models, laboratory observations were used in which shear stress was measured using an optimized Preston tube. This is then used to measure the SSD in various aspect ratios in the rectangular channel. To investigate the shear stress percentage, 10 data series with a total of 112 different data for were used. The results of the sensitivity analysis show that the most influential parameter for the SSD in smooth rectangular channel is the dimensionless parameter B/H, Where the transverse coordinate is B, and the flow depth is H. With the parameters (b/B), (B/H) for the bed and (z/H), (B/H) for the wall as inputs, the modeling of the GP was better than the other one. Based on the analysis, it can be concluded that the use of GP and ANFIS algorithms is more effective in estimating shear stress in smooth rectangular channels than the Tsallis entropy-based equations.

scholarly journals Non-linear deflection and stress analysis of laminated composite sandwich plate with elliptical cutout under different transverse loadings in hygro-thermal environment

2020 ◽  
Vol 7 (1) ◽  
pp. 80-100
Author(s):  
Rahul Kumar ◽  
Achchhe Lal ◽  
B. M. Sutaria
Keyword(s):  
Stress Concentration ◽  
Sandwich Plate ◽  
Thermal Environment ◽  
Shear Deformation Theory ◽  
Laminated Composite ◽  
Gauss Point ◽  
Composite Sandwich ◽  
Aspect Ratios ◽  
Present Solution ◽  
Non Linear

AbstractIn this paper, non-linear transverse deflection, stress and stress concentration factors (SCF) of isotropic and laminated composite sandwich plate (LCSP) with and without elliptical cutouts subjected to various trans-verse loadings in hygrothermal environment are studied. The basic formulation is based on secant function-based shear deformation theory (SFSDT) with von-Karman nonlinearity. The governing equation of non-linear deflection is derived using C0 finite element method (FEM) through minimum potential energy approach. Normalized trans-verse maximum deflections (NTMD) along with stress concentration factor is determined by using Newton’s Raphson method through Gauss point stress extrapolation. Influence of fiber orientations, load parameters, fiber volume fractions, plate span to thickness ratios, aspect ratios, thickness of core and face, position of core, boundary conditions, environmental conditions and types of transverse loading in MATLAB R2015a environment are examined. The numerical results using present solution methodology are verified with the results available in the literatures.

scholarly journals Microfabrication and Surface Functionalization of Soda Lime Glass through Direct Laser Interference Patterning

Nanomaterials ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 129
Author(s):  
Marcos Soldera ◽  
Sabri Alamri ◽  
Paul Alexander Sürmann ◽  
Tim Kunze ◽  
Andrés Fabián Lasagni
Keyword(s):  
Laser Radiation ◽  
Surface Functionalization ◽  
Incident Light ◽  
Chemical Properties ◽  
Visible Spectrum ◽  
Soda Lime ◽  
Soda Lime Glass ◽  
Textured Surfaces ◽  
Aspect Ratios ◽  
Direct Laser

All-purpose glasses are common in many established and emerging industries, such as microelectronics, photovoltaics, optical components, and biomedical devices due to their outstanding combination of mechanical, optical, thermal, and chemical properties. Surface functionalization through nano/micropatterning can further enhance glasses’ surface properties, expanding their applicability into new fields. Although laser structuring methods have been successfully employed on many absorbing materials, the processability of transparent materials with visible laser radiation has not been intensively studied, especially for producing structures smaller than 10 µm. Here, interference-based optical setups are used to directly pattern soda lime substrates through non-lineal absorption with ps-pulsed laser radiation in the visible spectrum. Line- and dot-like patterns are fabricated with spatial periods between 2.3 and 9.0 µm and aspect ratios up to 0.29. Furthermore, laser-induced periodic surface structures (LIPSS) with a feature size of approximately 300 nm are visible within these microstructures. The textured surfaces show significantly modified properties. Namely, the treated surfaces have an increased hydrophilic behavior, even reaching a super-hydrophilic state for some cases. In addition, the micropatterns act as relief diffraction gratings, which split incident light into diffraction modes. The process parameters were optimized to produce high-quality textures with super-hydrophilic properties and diffraction efficiencies above 30%.

scholarly journals Effects of Steel Fiber Percentage and Aspect Ratios on Fresh and Harden Properties of Ultra-High Performance Fiber

2021 ◽  
Vol 2 (3) ◽  
pp. 501-515
Author(s):  
Rajib Kumar Biswas ◽  
Farabi Bin Ahmed ◽  
Md. Ehsanul Haque ◽  
Afra Anam Provasha ◽  
Zahid Hasan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
High Performance ◽  
Steel Fiber ◽  
Setting Time ◽  
Fiber Reinforced Concrete ◽  
Future Research ◽  
Manufacturing Cost ◽  
Aspect Ratios ◽  
High Performance Fiber

Steel fibers and their aspect ratios are important parameters that have significant influence on the mechanical properties of ultrahigh-performance fiber-reinforced concrete (UHPFRC). Steel fiber dosage also significantly contributes to the initial manufacturing cost of UHPFRC. This study presents a comprehensive literature review of the effects of steel fiber percentages and aspect ratios on the setting time, workability, and mechanical properties of UHPFRC. It was evident that (1) an increase in steel fiber dosage and aspect ratio negatively impacted workability, owing to the interlocking between fibers; (2) compressive strength was positively influenced by the steel fiber dosage and aspect ratio; and (3) a faster loading rate significantly improved the mechanical properties. There were also some shortcomings in the measurement method for setting time. Lastly, this research highlights current issues for future research. The findings of the study are useful for practicing engineers to understand the distinctive characteristics of UHPFRC.

scholarly journals Surface Texturing of Si with Periodically Arrayed Oblique Nanopillars to Achieve Antireflection

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 380
Author(s):  
Jun-Hyun Kim ◽  
Sanghyun You ◽  
Chang-Koo Kim
Keyword(s):  
Aspect Ratio ◽  
Plasma Etching ◽  
Surface Texturing ◽  
Light Reflection ◽  
Si Substrate ◽  
Weighted Mean ◽  
Optical Reflectance ◽  
Si Substrates ◽  
Aspect Ratios ◽  
Shadowing Effect

Si surfaces were texturized with periodically arrayed oblique nanopillars using slanted plasma etching, and their optical reflectance was measured. The weighted mean reflectance (Rw) of the nanopillar-arrayed Si substrate decreased monotonically with increasing angles of the nanopillars. This may have resulted from the increase in the aspect ratio of the trenches between the nanopillars at oblique angles due to the shadowing effect. When the aspect ratios of the trenches between the nanopillars at 0° (vertical) and 40° (oblique) were equal, the Rw of the Si substrates arrayed with nanopillars at 40° was lower than that at 0°. This study suggests that surface texturing of Si with oblique nanopillars reduces light reflection compared to using a conventional array of vertical nanopillars.

Sign in / Sign up

Export Citation Format

Share Document