Piezoelectric inertial rotary actuator operating in two-step motion mode for eliminating backward motion

2020 ◽  
Vol 117 (3) ◽  
pp. 031902
Author(s):  
Yili Hu ◽  
Shengrong Lin ◽  
Jijie Ma ◽  
Yu Zhang ◽  
Jianping Li ◽  
...  
Keyword(s):  
Step Motion ◽  
Rotary Actuator ◽  
Motion Mode

The analysis on the influence of mixed sliding-rolling motion mode to precision degradation of ball screw

2021 ◽  
pp. 095440622098201
Author(s):  
Qiang Cheng ◽  
Baobao Qi ◽  
Hongyan Chu ◽  
Ziling Zhang ◽  
Zhifeng Liu ◽  
...  
Keyword(s):  
Structural Parameters ◽  
Experimental Tests ◽  
Theoretical Models ◽  
Operating Conditions ◽  
Ball Screw ◽  
Rolling Motion ◽  
Degradation Model ◽  
Sliding Motion ◽  
Factors Analysis ◽  
Motion Mode

The combination of sliding/rolling motion can influence the degree of precision degradation of ball screw. Precision degradation modeling and factors analysis can reveal the evolution law of ball screw precision. This paper presents a precision degradation model for factors analysis influencing precision due to mixed sliding-rolling motion. The precision loss model was verified through the comparison of theoretical models and experimental tests. The precision degradation due to rolling motion between the ball and raceway accounted for 29.09% of the screw precision loss due to sliding motion. Additionally, the total precision degradation due to rolling motion accounted for 21.03% of the total sliding precision loss of the screw and nut, and 17.38% of the overall ball screw precision loss under mixed sliding-rolling motion. In addition, the effects of operating conditions and structural parameters on precision loss were analyzed. The sensitivity coefficients of factors influencing were used to quantitatively describe impact degree on precision degradation.

scholarly journals Variable step control to improve scanning speed of gene sequencing stage

2021 ◽  
pp. 002029402110022
Author(s):  
Xiaohua Zhou ◽  
Jianbin Zheng ◽  
Xiaoming Wang ◽  
Wenda Niu ◽  
Tongjian Guo
Keyword(s):  
Motion Control ◽  
High Precision ◽  
High Speed ◽  
Stable State ◽  
Gene Sequencing ◽  
Scanning Speed ◽  
Settling Time ◽  
Step Motion ◽  
Variable Step ◽  
Step Control

High-speed scanning is a huge challenge to the motion control of step-scanning gene sequencing stage. The stage should achieve high-precision position stability with minimal settling time for each step. The existing step-scanning scheme usually bases on fixed-step motion control, which has limited means to reduce the time cost of approaching the desired position and keeping high-precision position stability. In this work, we focus on shortening the settling time of stepping motion and propose a novel variable step control method to increase the scanning speed of gene sequencing stage. Specifically, the variable step control stabilizes the stage at any position in a steady-state interval rather than the desired position on each step, so that reduces the settling time. The resulting step-length error is compensated in the next acceleration and deceleration process of stepping to avoid the accumulation of errors. We explicitly described the working process of the step-scanning gene sequencer and designed the PID control structure used in the variable step control for the gene sequencing stage. The simulation was performed to check the performance and stability of the variable step control. Under the conditions of the variable step control where the IMA6000 gene sequencer prototype was evaluated extensively. The experimental results show that the real gene sequencer can step 1.54 mm in 50 ms period, and maintain a high-precision stable state less than 30 nm standard deviation in the following 10 ms period. The proposed method performs well on the gene sequencing stage.

A planar reconfigurable linear rigid-body motion linkage with two operation modes

2014 ◽  
Vol 228 (16) ◽  
pp. 2985-2991 ◽  
Author(s):  
Guangbo Hao ◽  
Xianwen Kong ◽  
Xiuyun He
Keyword(s):  
Rigid Body ◽  
Single Mode ◽  
Rigid Body Motion ◽  
Body Motion ◽  
Reference Guide ◽  
Revolute Joints ◽  
Operation Modes ◽  
Straight Line ◽  
Motion Stage ◽  
Motion Mode

A planar reconfigurable linear (also rectilinear) rigid-body motion linkage (RLRBML) with two operation modes, that is, linear rigid-body motion mode and lockup mode, is presented using only R (revolute) joints. The RLRBML does not require disassembly and external intervention to implement multi-task requirements. It is created via combining a Robert’s linkage and a double parallelogram linkage (with equal lengths of rocker links) arranged in parallel, which can convert a limited circular motion to a linear rigid-body motion without any reference guide way. This linear rigid-body motion is achieved since the double parallelogram linkage can guarantee the translation of the motion stage, and Robert’s linkage ensures the approximate straight line motion of its pivot joint connecting to the double parallelogram linkage. This novel RLRBML is under the linear rigid-body motion mode if the four rocker links in the double parallelogram linkage are not parallel. The motion stage is in the lockup mode if all of the four rocker links in the double parallelogram linkage are kept parallel in a tilted position (but the inner/outer two rocker links are still parallel). In the lockup mode, the motion stage of the RLRBML is prohibited from moving even under power off, but the double parallelogram linkage is still moveable for its own rotation application. It is noted that further RLRBMLs can be obtained from the above RLRBML by replacing Robert’s linkage with any other straight line motion linkage (such as Watt’s linkage). Additionally, a compact RLRBML and two single-mode linear rigid-body motion linkages are presented.

Sign in / Sign up

Export Citation Format

Share Document