Modeling the effect of fabric weaving pattern on the kinetics of the impregnation process in the manufacturing of the fiber reinforced plastic structures

2019 ◽  
Author(s):  
P. P. Maung ◽  
G. Malysheva
Keyword(s):  
Fiber Reinforced ◽  
Impregnation Process ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Weaving Pattern ◽  
Kinetics Of

scholarly journals Stressing State Analysis of Reinforced Concrete Beam Strengthened by CFRP Sheet with Anchoring Device

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 576
Author(s):  
Liang Luo ◽  
Jie Lai ◽  
Jun Shi ◽  
Guorui Sun ◽  
Jie Huang ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Strain Distribution ◽  
Carbon Fiber Reinforced Plastic ◽  
Rc Beams ◽  
Fiber Reinforced ◽  
Strain Distribution Pattern ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Cfrp Sheet ◽  
Carbon Fiber Reinforced

This paper investigates the working performance of reinforcement concrete (RC) beams strengthened by Carbon-Fiber-Reinforced Plastic (CFRP) with different anchoring under bending moment, based on the structural stressing state theory. The measured strain values of concrete and Carbon-Fiber-Reinforced Plastic (CFRP) sheet are modeled as generalized strain energy density (GSED), to characterize the RC beams’ stressing state. Then the Mann–Kendall (M–K) criterion is applied to distinguish the characteristic loads of structural stressing state from the curve, updating the definition of structural failure load. In addition, for tested specimens with middle anchorage and end anchorage, the torsion applied on the anchoring device and the deformation width of anchoring device are respectively set parameters to analyze their effects on the reinforcement performance of CFRP sheet through comparing the strain distribution pattern of CFRP. Finally, in order to further explore the strain distribution of the cross-section and analyze the stressing-state characteristics of the RC beam, the numerical shape function (NSF) method is proposed to reasonably expand the limited strain data. The research results provide a new angle of view to conduct structural analysis and a reference to the improvement of reinforcement effect of CFRP.

scholarly journals Design of Center Pillar with Composite Reinforcements Using Hybrid Molding Method

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2047
Author(s):  
Ji-Heon Kang ◽  
Jae-Wook Lee ◽  
Jae-Hong Kim ◽  
Tae-Min Ahn ◽  
Dae-Cheol Ko
Keyword(s):  
Composite Materials ◽  
Weight Reduction ◽  
Fuel Efficiency ◽  
Vehicle Body ◽  
Process Time ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Molding Method ◽  
Reinforced Plastic ◽  
Composite Reinforcements

Recently, with the increase in awareness about a clean environment worldwide, fuel efficiency standards are being strengthened in accordance with exhaust gas regulations. In the automotive industry, various studies are ongoing on vehicle body weight reduction to improve fuel efficiency. This study aims to reduce vehicle weight by replacing the existing steel reinforcements in an automobile center pillar with a composite reinforcement. Composite materials are suitable for weight reduction because of their higher specific strength and stiffness compared to existing steel materials; however, one of the disadvantages is their high material cost. Therefore, a hybrid molding method that simultaneously performs compression and injection was proposed to reduce both process time and production cost. To replace existing steel reinforcements with composite materials, various reinforcement shapes were designed using a carbon fiber-reinforced plastic patch and glass fiber-reinforced plastic ribs. Structural analyses confirmed that, using these composite reinforcements, the same or a higher specific stiffness was achieved compared to the that of an existing center pillar using steel reinforcements. The composite reinforcements resulted in a 67.37% weight reduction compared to the steel reinforcements. In addition, a hybrid mold was designed and manufactured to implement the hybrid process.

scholarly journals Comparison of Mode Shapes of Carbon-Fiber-Reinforced Plastic Material Considering Carbon Fiber Direction

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 311
Author(s):  
Chan-Jung Kim
Keyword(s):  
Carbon Fiber ◽  
Modal Analysis ◽  
Dynamic Behavior ◽  
Mode Shapes ◽  
Modal Parameters ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Direction ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic

Previous studies have demonstrated the sensitivity of the dynamic behavior of carbon-fiber-reinforced plastic (CFRP) material over the carbon fiber direction by performing uniaxial excitation tests on a simple specimen. However, the variations in modal parameters (damping coefficient and resonance frequency) over the direction of carbon fiber have been partially explained in previous studies because all modal parameters have only been calculated using the representative summed frequency response function without modal analysis. In this study, the dynamic behavior of CFRP specimens was identified from experimental modal analysis and compared five CFRP specimens (carbon fiber direction: 0°, 30°, 45°, 60°, and 90°) and an isotropic SCS13A specimen using the modal assurance criterion. The first four modes were derived from the SCS13A specimen; they were used as reference modes after verifying with the analysis results from a finite element model. Most of the four mode shapes were found in all CFRP specimens, and the similarity increased when the carbon fiber direction was more than 45°. The anisotropic nature was dominant in three cases of carbon fiber, from 0° to 45°, and the most sensitive case was found in Specimen #3.

Study on the mechanism of inhomogeneous microdamage in short-pulse laser processing of carbon fiber reinforced plastic

2021 ◽  
pp. 073168442098359
Author(s):  
Luyao Xu ◽  
Jiuru Lu ◽  
Kangmei Li ◽  
Jun Hu
Keyword(s):  
Carbon Fiber ◽  
Pulse Energy ◽  
Short Pulse ◽  
Heterogeneous Material ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Processing Efficiency ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

In this article, a micro-heterogeneous material simulation model with carbon fiber and resin phase about laser ablation on carbon fiber reinforced plastic (CFRP) is established by Ansys. The ablation process of CFRP by nanosecond ultraviolet laser is simulated, and the mechanism of pulse energy and spot spacing on the heat-affected zone (HAZ) is studied, then the process parameters are optimized with the goal of HAZ size and processing efficiency, and finally the validity of the model is verified by experiments. It is found that the residual gradient and the width of the radial HAZ increase with the increase of the spot spacing, and the width of the axial HAZ decreases slightly with the increase of the spot spacing, which indicates the existence of the optimal spot spacing. Second, the ablation depth increases with the increase of the pulse energy, and the carbon fiber retains a relatively complete degree of exposure when the pulse energy is low, which has a certain guiding significance for the cleaning and bonding of CFRP.

Sign in / Sign up

Export Citation Format

Share Document