scholarly journals Research on simplified parametric finite element model of automobile frontal crash

2018 ◽  
Author(s):  
Linan Wu ◽  
Xin Zhang ◽  
Changhai Yang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Frontal Crash

scholarly journals Reconstruction finite element model of cars

2021 ◽  
Vol 4 (1) ◽  
pp. first
Author(s):  
Lý Hùng Anh ◽  
Nguyễn Phụ Thượng Lưu ◽  
Nguyễn Thiên Phú ◽  
Trần Đình Nhật
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Finite Element Models ◽  
Crash Analysis ◽  
Inertia Moment ◽  
Frontal Crash ◽  
Analysis Center ◽  
Simulation Results ◽  
And Behavior

The experimental method used in a frontal crash of cars costs much time and expense. Therefore, numerical simulation in crashworthiness is widely applied in the world. The completed car models contain a lot of parts which provided complicated structure, especially the rear of car models do not contribute to behavior of frontal crash which usually evaluates injuries of pedestrian or motorcyclist. In order to save time and resources, a simplification of the car models for research simulations is essential with the goal of reducing approximately 50% of car model elements and nodes. This study aims to construct the finite element models of front structures of vehicle based on the original finite element models. Those new car models must be maintained important values such as mass and center of gravity position. By using condition boundaries, inertia moment is kept unchanged on new model. The original car models, which are provided by the National Crash Analysis Center (NCAC), validated by using results from experimental crash tests. The modified (simplistic) vehicle FE models are validated by comparing simulation results with experimental data and simulation results of the original vehicle finite element models. LS-Dyna software provides convenient tools and very strong to modify finite element model. There are six car models reconstructed in this research, including 1 Pick-up, 2 SUV and 3 Sedan. Because car models were not the main object to evaluate in a crash, energy and behavior of frontal part have the most important role. As a result, six simplified car models gave reasonable outcomes and reduced significantly the number of nodes and elements. Therefore, the simulation time is also reduced a lot. Simplified car models can be applied to the upcoming frontal simulations.

Simulation of Vehicles Frontal Crash with Dummy Inside

2013 ◽  
Vol 760-762 ◽  
pp. 1244-1249
Author(s):  
Yuan Peng Liu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Energy Absorption ◽  
Element Model ◽  
Structure Deformation ◽  
Frontal Crash ◽  
Occupant Injury ◽  
Energy Absorbing

The complete Finite Element Model of vehicle with dummy inside is established. Through analyzing structure deformation and acceleration of the vehicle, the rule of energy absorption and dissipation is obtained, the dummys respond and the collision capability criteria of the head, chest and thigh are achieved. A comprehensive and credible appraisement about the frontal crash process and crashworthiness is proposed by analyzing the effect of the main energy-absorbing components, the transmitted route of the energy and the safety of the vehicle and occupant injury criterions.

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Sign in / Sign up

Export Citation Format

Share Document