Trapping and surface recombination of ion‐implanted deuterium in stainless steel

1984 ◽  
Vol 56 (6) ◽  
pp. 1561-1571 ◽  
Author(s):  
S. M. Myers ◽  
W. R. Wampler ◽  
F. Besenbacher
Keyword(s):  
Stainless Steel ◽  
Surface Recombination ◽  
Ion Implanted

Tribological Behavior of Ion Implanted AISI 440C Stainless Steel under Oil Lubricated Condition

2013 ◽  
Vol 419 ◽  
pp. 334-340 ◽  
Author(s):  
Feng Bin Liu ◽  
Hui Ping Li ◽  
Yan Cui ◽  
Jie Jian Di ◽  
Min Qu ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Tribological Behavior ◽  
Three Dimensional ◽  
Sample Surface ◽  
Surface Structures ◽  
Low Friction ◽  
Effect Mechanism ◽  
Nitrogen Ion ◽  
N Compounds ◽  
Ion Implanted

The tribological behaviors of nitrogen and titanium ion implanted AISI 440C stainless steel were studied by using an oscillating ball-on-disk tribometer under oil lubricated condition. The results showed that the ion implantations would significantly decrease the friction coefficient of the samples. To interpret the effect mechanism of the ion implantation on tribological performance, the surface morphology and oil wettability of the ion implanted samples were investigated by using a three-dimensional white interferometer and a contact angle analyzer, respectively. In addition, the surface structures and components of the samples were analyzed by using XRD and XPS techniques. The results indicated that the low friction coefficients of the ion implanted samples can be attributed to the new phases formed on the sample surfaces. For nitrogen ion implanted sample, the metal nitrides, supersaturated interstitial N and some C-O-N compounds appear on the sample surface. For titanium ion implanted sample, apart from TiO2and TiC phases form at the AISI 440C steel surface. Those components increase the surface energy of the AISI 440C steel and are in favor of the formation of the thin oil film.

Wear and Friction of Nitrogen Ion Implanted Steel

1983 ◽  
Vol 105 (2) ◽  
pp. 239-244 ◽  
Author(s):  
J. A. Kirk ◽  
G. W. Egerton ◽  
B. D. Sartwell
Keyword(s):  
Stainless Steel ◽  
Ion Implantation ◽  
Wear Behavior ◽  
304 Stainless Steel ◽  
Nitrogen Ion Implantation ◽  
Wide Range ◽  
Wear And Friction ◽  
Nitrogen Ion ◽  
Contact Pressures ◽  
Ion Implanted

A pin on disk wear test apparatus was used to evaluate wear and friction properties for nitrogen ion implanted and non-ion implanted steel disks in the presence of a lubricant. Both AISI/1018 mild steel and 304 stainless steel were examined. Typical fluence levels for ion implantation were above 1017 ions/cm2. In this paper disk wear is measured directly by a Talysurf profilometer tracing of the disk wear scar. By varying the contact area of the pin it was possible to evaluate wear behavior of both unimplanted and implanted disks over a wide range of contact pressures. It is shown that stainless steel disk wear can be decreased by nitrogen ion implantation, provided that contact pressures remain less than the yield strength of the substrate material. No significant wear improvements were observed for 1018 steel. To evaluate improvements in hardness due to nitrogen ion implantation, very low penetration depth microhardness measurements were made and the indentation diagonals were measured in a scanning electron microscope. These results and their limitations are also presented.

EBSD Studies of Ion Implanted Duplex Stainless Steel

2012 ◽  
Vol 18 (S2) ◽  
pp. 1346-1347
Author(s):  
J. Davis ◽  
K. Short ◽  
G. Lumpkin ◽  
K. Whittle ◽  
R. Wuhrer ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Ion Implanted

Extended abstract of a paper presented at Microscopy and Microanalysis 2012 in Phoenix, Arizona, USA, July 29 – August 2, 2012.

scholarly journals X-ray diffraction characterization of ion-implanted austenitic stainless steel

2005 ◽  
Vol 195 (1) ◽  
pp. 8-16 ◽  
Author(s):  
M.J. Marques ◽  
J. Pina ◽  
A.M. Dias ◽  
J.L. Lebrun ◽  
J. Feugeas
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ion Implanted
Sign in / Sign up

Export Citation Format

Share Document