Effect of wind speed and load power factor variation on optimal sizing of the machine and converters for double output induction generator based stand-alone wind energy conversion systems

2009 ◽  
Vol 1 (1) ◽  
pp. 013104 ◽  
Author(s):  
T. K. Saha ◽  
D. P. Bagarty ◽  
D. Kastha
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Energy Conversion ◽  
Power Factor ◽  
Induction Generator ◽  
Optimal Sizing ◽  
Wind Energy Conversion ◽  
Load Power ◽  
Wind Energy Conversion Systems ◽  
Energy Conversion Systems

scholarly journals Nonlinear Control Strategies of an Autonomous Double Fed Induction Generator Based Wind Energy Conversion Systems

2021 ◽  
Author(s):  
Nouha Bouchiba ◽  
Souhir Sallem ◽  
Mohamed Ben Ali Kammoun ◽  
Larbi Chrifi-Alaoui ◽  
Saïd Drid
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Energy Conversion ◽  
Induction Generator ◽  
Load Variations ◽  
Wind Energy Conversion ◽  
Wind Energy Conversion Systems ◽  
Energy Conversion Systems ◽  
The One ◽  
Double Fed Induction Generator

In the last few decades, among the wide range of renewable energy sources, wind energy is widely used. Variable speed wind energy conversion systems based on double fed induction generator have a considerable interest mostly in case of islanded networks and/or isolated applications. In this paper, as a means to supply remote areas, an investigation of a wind energy conversion system (WECS) based on a double fed induction generator (DFIG) is carried out. The presence of both wind turbine aerodynamics and DFIG coupled dynamics causes strong nonlinearities in the studied system. Wind speed and demanded power variations have a major impact on the quality of the produced energy. In order to control and maintain the stator output voltage and frequency at their nominal values (220 V/50 Hz) under wind speed and load variations, this work presents a study of three kinds of controllers: PI, Back-Stepping and Sliding Mode controllers. These controllers are integrated in the studied system and a comparison of their dynamic performances has been developed. Moreover, in order to ensure the rotor side converter safety on the one hand and to guarantee an optimal operation of the DFIG on the other hand, a management strategy is proposed in this work. Simulation results are performed using Matlab/Simulink environment and show the effectiveness and the accuracy of each controller compared to others mainly with the presence of wind speed and load demand variations.

scholarly journals A Condensed Introduction to the Doubly Fed Induction Generator Wind Energy Conversion Systems

2017 ◽  
Vol 2017 ◽  
pp. 1-18 ◽  
Author(s):  
Julius Mwaniki ◽  
Hui Lin ◽  
Zhiyong Dai
Keyword(s):  
Wind Energy ◽  
Energy Conversion ◽  
Wind Power ◽  
Market Share ◽  
Induction Generator ◽  
Doubly Fed Induction Generator ◽  
Wind Energy Conversion ◽  
Wind Energy Conversion Systems ◽  
Energy Conversion Systems ◽  
Doubly Fed

The increase in wind power penetration, at 456 GW as of June 2016, has resulted in more stringent grid codes which specify that the wind energy conversion systems (WECS) must remain connected to the system during and after a grid fault and, furthermore, must offer grid support by providing reactive currents. The doubly fed induction generator (DFIG) WECS is a well-proven technology, having been in use in wind power generation for many years and having a large world market share due to its many merits. Newer technologies such as the direct drive gearless permanent magnet synchronous generator have come up to challenge its market share, but the large number of installed machines ensures that it remains of interest in the wind industry. This paper presents a concise introduction of the DFIG WECS covering its construction, operation, merits, demerits, modelling, control types, levels and strategies, faults and their proposed solutions, and, finally, simulation. Qualities for the optimal control strategy are then proposed. The paper is intended to cover major issues related to the DFIG WECS that are a must for an overview of the system and hence serve as an introduction especially for new entrants into this area of study.

Reduced-order modeling approach for wind energy conversion systems based on the doubly-fed induction generator

2020 ◽  
pp. 106963
Author(s):  
Celso Rogerio Schmidlin Jr ◽  
Francisco Kleber de Araújo Lima ◽  
Fabrício Gonzalez Nogueira ◽  
Carlos Gustavo Castelo Branco ◽  
Fernando Lessa Tofoli
Keyword(s):  
Wind Energy ◽  
Energy Conversion ◽  
Reduced Order Modeling ◽  
Induction Generator ◽  
Doubly Fed Induction Generator ◽  
Reduced Order ◽  
Wind Energy Conversion ◽  
Wind Energy Conversion Systems ◽  
Energy Conversion Systems ◽  
Doubly Fed
Sign in / Sign up

Export Citation Format

Share Document