scholarly journals Evaluation of Dust Elements on Photovoltaic Module Performance: an Experimental Study

2021 ◽  
Vol 6 ◽  
pp. 30
Author(s):  
Hussein A. Kazem ◽  
Miqdam T. Chaichan ◽  
Ali H.A. Al-Waeli ◽  
Kamaruzzaman Sopian ◽  
Abdul Salam K. Darwish
Keyword(s):  
Power Plants ◽  
Building Materials ◽  
Photovoltaic Performance ◽  
Geographic Location ◽  
Cell Voltage ◽  
Photovoltaic Cell ◽  
Natural Phenomenon ◽  
Photovoltaic Module ◽  
Dust Component ◽  
High Concentrations

Dust is a natural phenomenon, and it represents all the components suspended in the air. Dust causes the photovoltaic performance to deteriorate. The main dust components concentrations vary from one geographic location to another and from one season to another. These components also have different effects on the PV power losses. Therefore, studying the effect of the concentration of each dust component separately can give a greater clarification and detail of how the accumulated dust affects the behavior of the PV module. In this study, the dust accumulated on a photovoltaic cell was collected and analyzed into its basic components. The results showed that most of the dust of Sohar city consists mostly of sand (65%) coming from the Empty Quarter desert adjacent to the Al-Batinah region. Also, volatile building materials such as cement and gypsum have high concentrations in this dust, which are 5.25% and 4.94%, respectively. In addition, high concentrations of ash 4.92%, which is resulting from burning fuels in smelters, power plants, and refineries. The effect of most of the studied dust components was limited on the current of the photovoltaic cell, but their effect was clearer on the cell voltage. As a result, the decrease in power generation was especially evident in the case of ash, cement, and new garment, but the biggest decrease was due to sand. While iron powder and red sand had the least effect on the performance of the photovoltaic cell.

scholarly journals Model of a Photovoltaic Cell for the MatLab/Simulink SimPowerSystems Library

2019 ◽  
Vol 62 (2) ◽  
pp. 135-145 ◽  
Author(s):  
D. I. Zalizny
Keyword(s):  
Solar Irradiance ◽  
Power Plants ◽  
Cell Model ◽  
Photovoltaic Cell ◽  
Design Stage ◽  
Photovoltaic Module ◽  
Model Parameters ◽  
Matlab Simulink ◽  
Photovoltaic Modules ◽  
Simulink Model

A new Simulink model of a photovoltaic cell has been proposed. The model is focused on the use of a standard SimPowerSystems library with power engineering elements from the MatLab/Simulink software package. The model allows altering the values of solar irradiance, photovoltaic cell temperature and load resistance. The results of the model application are the calculated values of voltages and currents at the photovoltaic cell output. The Simulink model that has been developed implements the known dependence of the photovoltaic cell volt-ampere characteristic by using both standard MatLab/Simulink blocks and special electric SimPowerSystems library blocks. The model is characterized by the fact that the series and parallel resistance of the photovoltaic cell are made in the form of resistors from the SimPowerSystems library. The main calculation algorithm is implemented programmatically by using the “C” programming language. To increase the algorithm stability to algebraic cycles the restrictions parameters are introduced. A new technique of calculating the photovoltaic cell model parameters based on experimental data has been proposed. The technique includes the preparation of a system of equations with experimental values of the photovoltaic cell voltages and currents. Experimental tests have been carried out for the photovoltaic module OSP XTP 250 under different solar irradiance values. The tests showed that the relative error of the Simulink model that has been developed does not exceed 12 %. The Simulink model makes it possible to build photovoltaic modules and then to build schemes of photovoltaic power plants as a part of power supply systems. Due to the latter it is possible to simulate the electricity consumers’ work, weather conditions, and the presence of shadows or pollution on the surface of photovoltaic modules. Also, one can carry out a simulation of increasing failures in power plant photovoltaic modules, e.g. simulating of modules efficiency reducing because of their degradation, or simulating of modules series resistance increasing because of the photovoltaic cell internal contacts deterioration. The Simulink model that has been developed can be used both at the design stage and at the stage of photoelectric power plants operation.

scholarly journals First-Time Source Apportionment Analysis of Deposited Particulate Matter from a Moss Biomonitoring Study in Northern Greece

Atmosphere ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 208 ◽  
Author(s):  
Chrysoula Betsou ◽  
Evangelia Diapouli ◽  
Evdoxia Tsakiri ◽  
Lambrini Papadopoulou ◽  
Marina Frontasyeva ◽  
...  
Keyword(s):  
Source Apportionment ◽  
Power Plants ◽  
Soil Dust ◽  
Northern Greece ◽  
Mining Operations ◽  
Moss Species ◽  
Elemental Concentrations ◽  
Pmf Model ◽  
Moss Biomonitoring ◽  
High Concentrations

Moss biomonitoring is a widely used technique for monitoring the accumulation of trace elements in airborne pollution. A total of one hundred and five samples, mainly of the Hypnum cupressiforme Hedw. moss species, were collected from the Northern Greece during the 2015/2016 European ICP Vegetation (International Cooperative Program on Effects of Air Pollution on Natural Vegetation and Crops) moss survey, which also included samples from the metalipherous area of Skouries. They were analyzed by means of neutron activation analysis, and the elemental concentrations were determined. A positive matrix factorization (PMF) model was applied to the results obtained for source apportionment. According to the PMF model, five sources were identified: soil dust, aged sea salt, road dust, lignite power plants, and a Mn-rich source. The soil dust source contributed the most to almost all samples (46% of elemental concentrations, on average). Two areas with significant impact from anthropogenic activities were identified. In West Macedonia, the emissions from a lignite power plant complex located in the area have caused high concentrations of Ni, V, Cr, and Co. The second most impacted area was Skouries, where mining activities and vehicular traffic (probably related to the mining operations) led to high concentrations of Mn, Ni, V, Co, Sb, and Cr.

scholarly journals Characterization of a Novel CaCO3-Forming Alkali-Tolerant Rhodococcus erythreus S26 as a Filling Agent for Repairing Concrete Cracks

Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2967
Author(s):  
Seunghoon Choi ◽  
Sungjin Park ◽  
Minjoo Park ◽  
Yerin Kim ◽  
Kwang Min Lee ◽  
...  
Keyword(s):  
Building Materials ◽  
Culture Fluid ◽  
Natural Phenomenon ◽  
Environment Friendly ◽  
Wide Range ◽  
Filling Agent ◽  
Calcium Source ◽  
Alkali Tolerance ◽  
High Alkali

Biomineralization, a well-known natural phenomenon associated with various microbial species, is being studied to protect and strengthen building materials such as concrete. We characterized Rhodococcus erythreus S26, a novel urease-producing bacterium exhibiting CaCO3-forming activity, and investigated its ability in repairing concrete cracks for the development of environment-friendly sealants. Strain S26 grown in solid medium formed spherical and polygonal CaCO3 crystals. The S26 cells grown in a urea-containing liquid medium caused culture fluid alkalinization and increased CaCO3 levels, indicating that ureolysis was responsible for CaCO3 formation. Urease activity and CaCO3 formation increased with incubation time, reaching a maximum of 2054 U/min/mL and 3.83 g/L, respectively, at day four. The maximum CaCO3 formation was achieved when calcium lactate was used as the calcium source, followed by calcium gluconate. Although cell growth was observed after the induction period at pH 10.5, strain S26 could grow at a wide range of pH 4–10.5, showing its high alkali tolerance. FESEM showed rhombohedral crystals of 20–60 µm in size. EDX analysis indicated the presence of calcium, carbon, and oxygen in the crystals. XRD confirmed these crystals as CaCO3 containing calcite and vaterite. Furthermore, R. erythreus S26 successfully repaired the artificially induced large cracks of 0.4–0.6 mm width.

scholarly journals Analysis of Power Generation for Solar Photovoltaic Module with Various Internal Cell Spacing

2021 ◽  
Vol 13 (11) ◽  
pp. 6364
Author(s):  
June Raymond L. Mariano ◽  
Yun-Chuan Lin ◽  
Mingyu Liao ◽  
Herchang Ay
Keyword(s):  
Power Output ◽  
Spacing Effect ◽  
Photovoltaic Cell ◽  
Standard Test ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Engineering Software ◽  
Internal Cell ◽  
Cell Spacing ◽  
Pv Module

Photovoltaic (PV) systems directly convert solar energy into electricity and researchers are taking into consideration the design of photovoltaic cell interconnections to form a photovoltaic module that maximizes solar irradiance. The purpose of this study is to evaluate the cell spacing effect of light diffusion on output power. In this work, the light absorption of solar PV cells in a module with three different cell spacings was studied. An optical engineering software program was used to analyze the reflecting light on the backsheet of the solar PV module towards the solar cell with varied internal cell spacing of 2 mm, 5 mm, and 8 mm. Then, assessments were performed under standard test conditions to investigate the power output of the PV modules. The results of the study show that the module with an internal cell spacing of 8 mm generated more power than 5 mm and 2 mm. Conversely, internal cell spacing from 2 mm to 5 mm revealed a greater increase of power output on the solar PV module compared to 5 mm to 8 mm. Furthermore, based on the simulation and experiment, internal cell spacing variation showed that the power output of a solar PV module can increase its potential to produce more power from the diffuse reflectance of light.

scholarly journals Predicting the Performance of Solar Power Generation Using Deep Learning Methods

2021 ◽  
Vol 11 (15) ◽  
pp. 6887
Author(s):  
Chung-Hong Lee ◽  
Hsin-Chang Yang ◽  
Guan-Bo Ye
Keyword(s):  
Power Generation ◽  
Solar Energy ◽  
Power Output ◽  
Power Plants ◽  
Solar Power ◽  
Photovoltaic Cell ◽  
Power Prediction ◽  
Seasonal Characteristics ◽  
Variable Nature ◽  
Solar Power Plants

In recent years, many countries have provided promotion policies related to renewable energy in order to take advantage of the environmental factors of sufficient sunlight. However, the application of solar energy in the power grid also has disadvantages. The most obvious is the variability of power output, which will put pressure on the system. As more grid reserves are needed to compensate for fluctuations in power output, the variable nature of solar power may hinder further deployment. Besides, one of the main issues surrounding solar energy is the variability and unpredictability of sunlight. If it is cloudy or covered by clouds during the day, the photovoltaic cell cannot produce satisfactory electricity. How to collect relevant factors (variables) and data to make predictions so that the solar system can increase the power generation of solar power plants is an important topic that every solar supplier is constantly thinking about. The view is taken, therefore, in this work, we utilized the historical monitoring data collected by the ground-connected solar power plants to predict the power generation, using daily characteristics (24 h) to replace the usual seasonal characteristics (365 days) as the experimental basis. Further, we implemented daily numerical prediction of the whole-point power generation. The preliminary experimental evaluations demonstrate that our developed method is sensible, allowing for exploring the performance of solar power prediction.

TRACE ELEMENT ANALYSIS OF FLY ASH BY PIXE

1999 ◽  
Vol 09 (03n04) ◽  
pp. 417-422 ◽  
Author(s):  
V. VIJAYAN ◽  
S. N. BEHERA
Keyword(s):  
Fly Ash ◽  
Trace Element ◽  
Power Plants ◽  
Building Materials ◽  
Thermal Power ◽  
Trace Element Analysis ◽  
Chemical Properties ◽  
Solid Material ◽  
Thermal Power Plants ◽  
Element Analysis

Fly ash is a major component of solid material generated by the coal-fired thermal power plants. In India the total amount of fly ash produced per annum is around 100 million tonnes. Fly ash has a great potential for utilization in making industrial products such as cement, bricks as well as building materials, besides being used as a soil conditioner and a provider of micro nutrients in agriculture. However, given the large amount of fly ash that accumulate at thermal power plants, their possible reuse and dispersion and mobilization into the environment of the various elements depend on climate, soils, indigenous vegetation and agriculture practices. Fly ash use in agriculture improved various physico-chemical properties of soil, particularly the water holding capacity, porosity and available plant nutrients. However it is generally apprehended that the application of large quantity of fly ash in fields may affect the plant growth and soil texture. Hence there is a need to characterize trace elements of fly ash. The results of trace element analysis of fly ash and pond ash samples collected from major thermal power plants of India by Particle Induced X-ray Emission (PIXE) have been discussed.

scholarly journals Use of Ash-and-Slag Wastes after Burning of Fine-Dispersed Coal-Washing Wastes

2018 ◽  
Vol 41 ◽  
pp. 01042
Author(s):  
Vasilii Murko ◽  
Veniamin Khyamyalyainen ◽  
Marina Baranova
Keyword(s):  
Power Plants ◽  
Building Materials ◽  
Negative Impact ◽  
Mineralogical Composition ◽  
Unburned Carbon ◽  
Crushed Rock ◽  
Low Carbon ◽  
Technological Parameters ◽  
Coal Fuel ◽  
Granulated Slag

Effective utilization of ash-and-slag waste generated by coalfired power plants can help significantly to reduce the negative impact on the environment and improve their economic performance. Studies have been made of the mineralogical composition of ash-and-slag wastes obtained after the combustion of water-coal fuel based on fine-dispersed coal-washing waste (filter cake) in a specially designed boiler with a vortex combustion system. The possibility of effective use of ash-and-slag wastes for the production of building materials, primarily mortar mixes, widely used for mining works on mine openings, laying the worked out space, etc. (high content of silicon oxide and aluminum oxide is combined with a low carbon content in other words a negligible unburned carbon loss). The optimum percentage ratio of the initial components of the filling mixture based on ash-and-slag wastes and crushed rock (granulated slag) has been established. The results of experimental tests of hardening tabs on the strength under uniaxial compression are presented. It has been established that a sample containing 18% of ash-and-slag wastes, 33% of a granulated slag and 19% of cement, corresponds to the required technological parameters for the strength and cement content.

scholarly journals Performance Analysis of Photovoltaic Panels Under the Effect of Electrical and Environmental Parameters in Erbil City

2021 ◽  
Vol 5 (1) ◽  
pp. 101-110
Author(s):  
Banaz S. Ibrahim ◽  
Sarkar Jawhar M. Shareef ◽  
Hilmi F. Ameen
Keyword(s):  
Performance Analysis ◽  
Equivalent Circuit ◽  
Model Simulation ◽  
Photovoltaic Performance ◽  
Environmental Parameters ◽  
Photovoltaic Cell ◽  
Matlab Simulation ◽  
Shunt Resistance ◽  
Photovoltaic Panel ◽  
Bird Droppings

This paper presents the performance analysis of a photovoltaic cell derived from a single diode equivalent circuit under the influence of several kinds of electrical and environmental parameters. The characteristics of a solar cell have been investigated using MATLAB simulation and have been validated experimentally. In this paper the photovoltaic cell is represented by an exact equivalent circuit including all parameters such as a diode saturation current, light generated current, temperature effects, series and shunt resistance values. Also, this paper includes the impacts of clouds, dust, chalk powder, fly ash and bird droppings on the efficiency of the photovoltaic panel. A comparison between the experimental and model simulation results confirmed the reality of results, and indicate the validity of the exact model for photovoltaic performance analysis.

scholarly journals A dynamic model for series and parallel resistance of photovoltaic cell using material properties extraction and energy tunnel

2017 ◽  
Vol 16 (1) ◽  
pp. 9-21
Author(s):  
Kotchapong Sumanonta ◽  
Pasist Suwanapingkarl ◽  
Pisit Liutanakul
Keyword(s):  
Series Resistance ◽  
Photovoltaic Cell ◽  
Photovoltaic Module ◽  
Practical Application ◽  
Pv Module ◽  
Proposed Model ◽  
Outdoor Test ◽  
The Relationship ◽  
Parallel Resistance ◽  
Novel Model

This article presents a novel model for the equivalent circuit of a photovoltaic module. This circuit consists of the following important parameters: a single diode, series resistance (Rs) and parallel resistance (Rp) that can be directly adjusted according to ambient temperature and the irradiance. The single diode in the circuit is directly related to the ideality factor (m), which represents the relationship between the materials and significant structures of PV module such as mono crystalline, multi crystalline and thin film technology.  Especially, the proposed model in this article is to present the simplified model that can calculate the results of I-V curves faster and more accurate than other methods of the previous models. This can show that the proposed models are more suitable for the practical application. In addition, the results of the proposed model are validated by the datasheet, the practical data in the laboratory (indoor test) and the onsite data (outdoor test). This ensures that the less than 0.1% absolute errors of the model can be accepted.

Sign in / Sign up

Export Citation Format

Share Document