Dynamic mechanical load emulation test facility to evaluate the performance of AC inverters

2000 ◽  
Vol 14 (1) ◽  
pp. 21-28 ◽  
Author(s):  
C.R. Hewson ◽  
P.W. Wheeler ◽  
G.M. Asher ◽  
M. Sumner
Keyword(s):  
Mechanical Load ◽  
Test Facility ◽  
Dynamic Mechanical

NMR imaging of technical SBR vulcanizates under dynamic mechanical load

1997 ◽  
Vol 198 (9) ◽  
pp. 2729-2742 ◽  
Author(s):  
Daniela Hauck ◽  
Peter Blümler ◽  
Bernhard Blümich
Keyword(s):  
Mechanical Load ◽  
Nmr Imaging ◽  
Dynamic Mechanical

scholarly journals Analysis of Steam Explosion under Conditions of Partially Flooded Cavity and Submerged Reactor Vessel

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Sang Ho Kim ◽  
Seong-Wan Hong ◽  
Rae-Joon Park
Keyword(s):  
Steam Explosion ◽  
Mechanical Load ◽  
Free Fall ◽  
Severe Accident ◽  
Test Facility ◽  
Pressurized Water Reactor ◽  
Pressurized Water ◽  
Total Load ◽  
Entry Velocity ◽  
Fall Height

A steam explosion in a reactor cavity makes a mechanical load of the pressure pulse, which can result in a failure of the containment isolation. To prove the integrity of the containment during the ex-vessel steam explosion, the effects of water conditions on a steam explosion have to be identified, and the impulse of a steam explosion has to be exactly assessed. In this study, the analyses for steam explosions were performed for the conditions of a partially flooded cavity and a submerged-vessel in a pressurized water reactor. The entry velocity of a corium jet for the scale of the test facility was varied to simulate the two plant conditions. The TEXAS-V code was used for simulating the phases of premixing and explosion, and the load of a steam explosion was estimated based on the pressure variation. The impulse of a steam explosion under the condition of a corium jet falling into water without a free-fall height is bigger than that under a free-fall height. The fragmented mass of corium in an explosion phase and the distribution of steam fraction are the main parameters for the total load of the steam explosion. This study is expected to contribute to analyses of a steam explosion for a severe accident management strategy.

scholarly journals Optimizing Viscoelastic Properties of Rubber Compounds for Ballistic Applications

2020 ◽  
Vol 10 (21) ◽  
pp. 7840
Author(s):  
Janis Karl ◽  
Franziska Kirsch ◽  
Norbert Faderl ◽  
Leonhard Perko ◽  
Teresa Fras
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Mechanical Stress ◽  
Mechanical Load ◽  
Superposition Principle ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Ballistic Impact ◽  
Dynamic Mechanical

Using interlayers of rubber adds a positive effect to the synergy of disruptor–absorber armors. Emerging from its viscoelasticity the material is able to transform mechanical stress into heat. The dynamic mechanical properties of elastomers depend on both ambient temperature and frequency of an applied mechanical load. The damping shows a maximum in the glass transition area. If the frequency of the glass transition is in the magnitude of the mechanical stress rate applied by ballistic impact, the elastomer will undergo the transition and thus show maximized damping. An ideal material for ballistic protection against small calibers is developed by making use of dynamic mechanical analysis and the time–temperature superposition principle. The material is later analyzed by ballistic experiments and compared to other nonideal rubbers with regard to glass transition temperature, hardness and damping. It is shown that by choosing a material correctly with certain glass transition temperature and hardness, the ballistic properties of a steel–rubber–aluminum armor can be enhanced. The chosen material (butyl rubber) with a hardness of 50 °ShA is able to enhance energy absorption during ballistic impact by around 8%, which is twice as good as other rubber with non-optimized properties.

Sign in / Sign up

Export Citation Format

Share Document