scholarly journals Enhanced electromechanical performance through chemistry graft copper phthalocyanine to siloxane‐modified polyurethane and interpenetrate with siloxane silicon rubber as composite actuator material

2021 ◽  
Vol 4 (1) ◽  
pp. 38-44
Author(s):  
Tingting Huang ◽  
Bolei Yuan ◽  
Jun Tang ◽  
Yunhe Zhang
Keyword(s):  
Copper Phthalocyanine ◽  
Silicon Rubber ◽  
Composite Actuator ◽  
Electromechanical Performance

High-Resolution Cryo-Electron Microscopy of Biological Macromolecules

1990 ◽  
Vol 48 (1) ◽  
pp. 126-127
Author(s):  
Yoshinori Fujiyoshi
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Diffraction Pattern ◽  
Superfluid Helium ◽  
Copper Phthalocyanine ◽  
Optical Diffraction ◽  
Irradiation Damage ◽  
Biological Macromolecules ◽  
Cross Sectional ◽  
Instrumental Resolution

The resolution of direct images of biological macromolecules is normally restricted to far less than 0.3 nm. This is not due instrumental resolution, but irradiation damage. The damage to biological macromolecules may expect to be reduced when they are cooled to a very low temperature. We started to develop a new cryo-stage for a high resolution electron microscopy in 1983, and successfully constructed a superfluid helium stage for a 400 kV microscope by 1986, whereby chlorinated copper-phthalocyanine could be photographed to a resolution of 0.26 nm at a stage temperature of 1.5 K. We are continuing to develop the cryo-microscope and have developed a cryo-microscope equipped with a superfluid helium stage and new cryo-transfer device.The New cryo-microscope achieves not only improved resolution but also increased operational ease. The construction of the new super-fluid helium stage is shown in Fig. 1, where the cross sectional structure is shown parallel to an electron beam path. The capacities of LN2 tank, LHe tank and the pot are 1400 ml, 1200 ml and 3 ml, respectively. Their surfaces are placed with gold to minimize thermal radiation. Consumption rates of liquid nitrogen and liquid helium are 170 ml/hour and 140 ml/hour, respectively. The working time of this stage is more than 7 hours starting from full LN2 and LHe tanks. Instrumental resolution of our cryo-stage cooled to 4.2 K was confirmed to be 0.20 nm by an optical diffraction pattern from the image of a chlorinated copper-phthalocyanine crystal. The image and the optical diffraction pattern are shown in Fig. 2 a, b, respectively.

Copper phthalocyanine-chitin, an adsorbent for carcinogen–nucleotide adducts

1999 ◽  
Author(s):  
Hikoya Hayatsu ◽  
Sanae Mimaki ◽  
Nao Ishizaki ◽  
Keiji Wakabayashi ◽  
Chitose Sugiyama
Keyword(s):  
Copper Phthalocyanine

Determining the exciton diffusion length of copper phthalocyanine in operating planar-heterojunction organic solar cells

2020 ◽  
Vol 89 (3) ◽  
pp. 30201 ◽  
Author(s):  
Xi Guan ◽  
Shiyu Wang ◽  
Wenxing Liu ◽  
Dashan Qin ◽  
Dayan Ban
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Diffusion Length ◽  
Copper Phthalocyanine ◽  
Short Circuit ◽  
Thick Layer ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Exciton Diffusion ◽  
Exciton Diffusion Length

Organic solar cells based on planar copper phthalocyanine (CuPc)/C60 heterojunction have been characterized, in which a 2 nm-thick layer of bathocuproine (BCP) is inserted into the CuPc layer. The thin layer of BCP allows hole current to tunnel it through but blocks the exciton diffusion, thereby altering the steady-state exciton profile in the CuPc zone (zone 1) sandwiched between BCP and C60. The short-circuit current density (JSC) of device is limited by the hole-exciton scattering effect at the BCP/CuPc (zone 1) interface. Based on the variation of JSC with the width of zone 1, the exciton diffusion length of CuPc is deduced to be 12.5–15 nm. The current research provides an easy and helpful method to determine the exciton diffusion lengths of organic electron donors.

scholarly journals Complex Geometry Strain Sensors Based on 3D Printed Nanocomposites: Spring, Three-Column Device and Footstep-Sensing Platform

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1106
Author(s):  
Alejandro Cortés ◽  
Xoan F. Sánchez-Romate ◽  
Alberto Jiménez-Suárez ◽  
Mónica Campo ◽  
Ali Esmaeili ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
3D Printing ◽  
Complex Geometry ◽  
Uv Light ◽  
Shielding Effect ◽  
Strain Sensitivity ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Sensing Platform ◽  
Electromechanical Performance

Electromechanical sensing devices, based on resins doped with carbon nanotubes, were developed by digital light processing (DLP) 3D printing technology in order to increase design freedom and identify new future and innovative applications. The analysis of electromechanical properties was carried out on specific sensors manufactured by DLP 3D printing technology with complex geometries: a spring, a three-column device and a footstep-sensing platform based on the three-column device. All of them show a great sensitivity of the measured electrical resistance to the applied load and high cyclic reproducibility, demonstrating their versatility and applicability to be implemented in numerous items in our daily lives or in industrial devices. Different types of carbon nanotubes—single-walled, double-walled and multi-walled CNTs (SWCNTs, DWCNTs, MWCNTs)—were used to evaluate the effect of their morphology on electrical and electromechanical performance. SWCNT- and DWCNT-doped nanocomposites presented a higher Tg compared with MWCNT-doped nanocomposites due to a lower UV light shielding effect. This phenomenon also justifies the decrease of nanocomposite Tg with the increase of CNT content in every case. The electromechanical analysis reveals that SWCNT- and DWCNT-doped nanocomposites show a higher electromechanical performance than nanocomposites doped with MWCNTs, with a slight increment of strain sensitivity in tensile conditions, but also a significant strain sensitivity gain at bending conditions.

Sign in / Sign up

Export Citation Format

Share Document