Study on Gas-tightness detection analysis and leak test of UHV AC GIL

2021 ◽  
Author(s):  
Y. Hao ◽  
S. Jin ◽  
X. Li ◽  
H. Tian ◽  
Z. Liu ◽  
...  
Keyword(s):  
Leak Test ◽  
Detection Analysis ◽  
Gas Tightness

Selective Corrosion of brazed joint between BNi-2 filler metal and stainless steel 316

1996 ◽  
Vol 54 ◽  
pp. 218-219
Author(s):  
H. S. Kim ◽  
R. U. Lee
Keyword(s):  
Stainless Steel ◽  
Filler Metal ◽  
Surface Preparation ◽  
Optical Microscope ◽  
Heating Element ◽  
Incomplete Fusion ◽  
Atmospheric Conditions ◽  
Leak Test ◽  
High Temperature Side ◽  
Inconel 600

A heating element/electrical conduit assembly used in the Orbiter Maneuvering System failed a leak test during a routine refurbishment inspection. The conduit, approximately 100 mm in length and 12 mm in diameter, was fabricated from two tubes and braze-joined with a sleeve. The tube on the high temperature side (heating element side) and the sleeve were made of Inconel 600 and the other tube was stainless steel (SS) 316. For the filler metal, a Ni-Cr-B brazing alloy per AWS BNi-2, was used. A Helium leak test spotted the leak located at the joint between the sleeve and SS 316 tubing. This joint was dissected, mounted in a plastic mold, polished, and examined with an optical microscope. Debonding of the brazed surfaces was noticed, more pronounced toward the sleeve end which was exposed to uncontrolled atmospheric conditions intermittently. Initially, lack of wetting was suspected, presumably caused by inadequate surface preparation or incomplete fusion of the filler metal. However, this postulation was later discarded based upon the following observations: (1) The angle of wetting between the fillet and tube was small, an indication of adequate wetting, (2) the fillet did not exhibit a globular microstructure which would be an indication of insufficient melting of the filler metal, and (3) debonding was intermittent toward the midsection of the sleeve.

Yttrium Oxyhydrides for Photochromic Applications: Correlating Composition and Optical Response

2018 ◽  
Author(s):  
Dmitrii Moldarev ◽  
Elbruz M. Baba ◽  
Marcos V. Moro ◽  
Chang C. You ◽  
Smagul Zh. Karazhanov ◽  
...  
Keyword(s):  
Medical Devices ◽  
Ternary Diagram ◽  
Optical And Electrical Properties ◽  
Ambient Conditions ◽  
Elastic Recoil ◽  
Elastic Recoil Detection Analysis ◽  
Photochromic Properties ◽  
Smart Windows ◽  
Elastic Recoil Detection ◽  
Detection Analysis

It has been recently demonstrated that yttrium oxyhydride(YHO) films can exhibit reversible photochromic properties when exposed to illumination at ambient conditions. This switchable optical propertyenables their utilization in many technological applications, such as smart windows, sensors, goggles, medical devices, etc. However, how the composition of the films affects their optical properties is not fully clear and therefore demands a straightforward investigation. In this work, the composition of YHO films manufactured by reactive magnetron sputtering under different conditions is deduced in a ternary diagram from Time-of-Flight Elastic Recoil Detection Analysis (ToF-ERDA). The results suggest that stable compounds are formed with a specificchemical formula – YH<sub>2-δ</sub>O<sub>δ</sub>. In addition, optical and electrical properties of the films are investigated, and a correlation with their compositions is established. The corresponding photochromic response is found in a specific oxygen concentration range (0.45 < δ < 1.5) with maximum and minimum of magnitude on the lower and higher border, respectively.

Sign in / Sign up

Export Citation Format

Share Document