Open-circuit to short-circuit switching: method for lifetime measurement in solar cells

1979 ◽  
Vol 15 (15) ◽  
pp. 456 ◽  
Author(s):  
S.R. Dhariwal ◽  
Niranjan Basu ◽  
Ranjana Gadre
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Lifetime Measurement ◽  
Open Circuit ◽  
Circuit Switching ◽  
Switching Method

Lock-in Thermography-Based Local Efficiency Analysis of Solar Cells

2012 ◽  
Author(s):  
Otwin Breitenstein
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Efficiency Analysis ◽  
Open Circuit ◽  
Local Defect ◽  
Whole Cell ◽  
Local Efficiency ◽  
Cell Efficiency ◽  
Lock In ◽  
Efficiency Data

Abstract The electronic properties of solar cells, particularly multicrystalline silicon-based ones, are distributed spatially inhomogeneous, where regions of poor quality may degrade the performance of the whole cell. These inhomogeneities mostly affect the dark current-voltage (I-V) characteristic, which decisively affects the efficiency. Since the grid distributes the local voltage homogeneously across the cell and leads to lateral balancing currents, local light beam-induced current methods alone cannot be used to image local cell efficiency parameters. Lock-in thermography (LIT) is the method of choice for imaging inhomogeneities of the dark I-V characteristic. This contribution introduces a novel method for evaluating a number of LIT images taken at different applied biases. By pixel-wise fitting the data to a two diode model and taking into account local series resistance and short circuit current density data, realistically simulated images of the other cell efficiency parameters (open circuit voltage, fill factor, and efficiency) are obtained. Moreover, simulated local and global dark and illuminated I-V characteristics are obtained, also for various illumination intensities. These local efficiency data are expectation values, which would hold if a homogeneous solar cell had the properties of the selected region of the inhomogeneous cell. Alternatively, also local efficiency data holding for the cell working at its own maximum power point may be generated. The amount of degradation of different cell efficiency parameters in some local defect positions is an indication how dangerous these defects are for degrading this parameter of the whole cell. The method allows to virtually 'cut out' certain defects for checking their influence on the global characteristics. Thus, by applying this method, a detailed local efficiency analysis of locally inhomogeneous solar cells is possible. It can be reliably predicted how a cell would improve if certain defects could be avoided. This method is implemented in a software code, which is available.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

scholarly journals Ultrathin Cu(In,Ga)Se2 Solar Cells with Ag/AlOx Passivating Back Reflector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4268
Author(s):  
Jessica de Wild ◽  
Gizem Birant ◽  
Guy Brammertz ◽  
Marc Meuris ◽  
Jef Poortmans ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Electron Microscopic ◽  
Current Increase ◽  
Time Resolved ◽  
Cigs Solar Cells

Ultrathin Cu(In,Ga)Se2 (CIGS) absorber layers of 550 nm were grown on Ag/AlOx stacks. The addition of the stack resulted in solar cells with improved fill factor, open circuit voltage and short circuit current density. The efficiency was increased from 7% to almost 12%. Photoluminescence (PL) and time resolved PL were improved, which was attributed to the passivating properties of AlOx. A current increase of almost 2 mA/cm2 was measured, due to increased light scattering and surface roughness. With time of flight—secondary ion mass spectroscopy, the elemental profiles were measured. It was found that the Ag is incorporated through the whole CIGS layer. Secondary electron microscopic images of the Mo back revealed residuals of the Ag/AlOx stack, which was confirmed by energy dispersive X-ray spectroscopy measurements. It is assumed to induce the increased surface roughness and scattering properties. At the front, large stains are visible for the cells with the Ag/AlOx back contact. An ammonia sulfide etching step was therefore applied on the bare absorber improving the efficiency further to 11.7%. It shows the potential of utilizing an Ag/AlOx stack at the back to improve both electrical and optical properties of ultrathin CIGS solar cells.

17.8%-efficient Amorphous Silicon Heterojunction Solar Cells on p-type Silicon Wafers

2006 ◽  
Vol 910 ◽  
Author(s):  
Qi Wang ◽  
Matt P. Page ◽  
Eugene Iwancizko ◽  
Yueqin Xu ◽  
Yanfa Yan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Amorphous Silicon ◽  
High Efficiency ◽  
Short Circuit ◽  
Open Circuit ◽  
Layer Growth ◽  
Surface Recombination Velocity ◽  
Back Contact ◽  
P Type

AbstractWe have achieved an independently-confirmed 17.8% conversion efficiency in a 1-cm2, p-type, float-zone silicon (FZ-Si) based heterojunction solar cell. Both the front emitter and back contact are hydrogenated amorphous silicon (a-Si:H) deposited by hot-wire chemical vapor deposition (HWCVD). This is the highest reported efficiency for a HWCVD silicon heterojunction (SHJ) solar cell. Two main improvements lead to our most recent increases in efficiency: 1) the use of textured Si wafers, and 2) the application of a-Si:H heterojunctions on both sides of the cell. Despite the use of textured c-Si to increase the short-circuit current, we were able to maintain the same 0.65 V open-circuit voltage as on flat c-Si. This is achieved by coating a-Si:H conformally on the c-Si surfaces, including covering the tips of the anisotropically-etched pyramids. A brief atomic H treatment before emitter deposition is not necessary on the textured wafers, though it was helpful in the flat wafers. It is essential to high efficiency SHJ solar cells that the emitter grows abruptly as amorphous silicon, instead of as microcrystalline or epitaxial Si. The contact on each side of the cell comprises a thin (< 5 nm) low substrate temperature (~100°C) intrinsic a-Si:H layer, followed by a doped layer. Our intrinsic layers are deposited at 0.3-1.2 nm/s. The doped emitter and back-contact layers were deposited at a higher temperature (>200°C) and grown from PH3/SiH4/H2 and B2H6/SiH4/H2 doping gas mixtures, respectively. This combination of low (intrinsic) and high (doped layer) growth temperatures was optimized by lifetime and surface recombination velocity measurements. Our rapid efficiency advance suggests that HWCVD may have advantages over plasma-enhanced (PE) CVD in fabrication of high-efficiency heterojunction c-Si cells; there is no need for process optimization to avoid plasma damage to the delicate, high-quality, Si wafers.

scholarly journals Dye-Sensitized Nanocrystalline ZnO Solar Cells Based on Ruthenium(II) Phendione Complexes

2011 ◽  
Vol 2011 ◽  
pp. 1-10 ◽  
Author(s):  
Hashem Shahroosvand ◽  
Parisa Abbasi ◽  
Mohsen Ameri ◽  
Mohammad Reza Riahi Dehkordi
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Conversion Efficiency ◽  
Short Circuit ◽  
Photocurrent Density ◽  
Open Circuit ◽  
Zno Thin Film ◽  
Photovoltaic Properties ◽  
Dye Sensitized ◽  
Ft Ir

The metal complexes ( (phen)2(phendione))(PF6)2(1), [ (phen)(bpy)(phendione))(PF6)2(2), and ( (bpy)2(phendione))(PF6)2(3) (phen = 1,10-phenanthroline, bpy = 2,2′-bipyridine and phendione = 1,10-phenanthroline-5,6-dione) have been synthesized as photo sensitizers for ZnO semiconductor in solar cells. FT-IR and absorption spectra showed the favorable interfacial binding between the dye-molecules and ZnO surface. The surface analysis and size of adsorbed dye on nanostructure ZnO were further examined with AFM and SEM. The AFM images clearly show both, the outgrowth of the complexes which are adsorbed on ZnO thin film and the depression of ZnO thin film. We have studied photovoltaic properties of dye-sensitized nanocrystalline semiconductor solar cells based on Ru phendione complexes, which gave power conversion efficiency of (η) of 1.54% under the standard AM 1.5 irradiation (100 mW cm−2) with a short-circuit photocurrent density () of 3.42 mA cm−2, an open-circuit photovoltage () of 0.622 V, and a fill factor (ff) of 0.72. Monochromatic incident photon to current conversion efficiency was 38% at 485 nm.

Thiocyanate Free Ruthenium(II) Complexes for Dye Sensitized Solar Cells (DSSCs)

2018 ◽  
Vol 382 ◽  
pp. 369-373
Author(s):  
Usana Mahanitipong ◽  
Preeyapat Prompan ◽  
Rukkiat Jitchati
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Visible Region ◽  
Photocurrent Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Ligand Charge Transfer ◽  
Sensitized Solar Cells ◽  
Open Circuit Photovoltage

The four thiocyanate free ruthenium(II) complexes; [Ru(N^N)2(C^N)]PF6were synthesized and characterized for dye sensitized solar cells (DSSCs). The results showed that the broad absorptions covered the visible region from metal to ligand charge transfer (MLCT) were obtained with the main peaks at 560, 490 and 400 nm. The materials were studied DSSC performance under standard AM 1.5. Compound PP1 showed the power conversion efficiency (PCE) at 3.10%, with a short-circuit photocurrent density (Jsc) of 7.99 mA cm-2, an open-circuit photovoltage (Voc) of 563 mV and a high fill factor (ff) of 0.690.

scholarly journals Direct AFM-based nanoscale mapping and tomography of open-circuit voltages for photovoltaics

2018 ◽  
Vol 9 ◽  
pp. 1802-1808 ◽  
Author(s):  
Katherine Atamanuk ◽  
Justin Luria ◽  
Bryan D Huey
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Three Dimensional ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Order Of Magnitude ◽  
Individual Grains

The nanoscale optoelectronic properties of materials can be especially important for polycrystalline photovoltaics including many sensor and solar cell designs. For thin film solar cells such as CdTe, the open-circuit voltage and short-circuit current are especially critical performance indicators, often varying between and even within individual grains. A new method for directly mapping the open-circuit voltage leverages photo-conducting AFM, along with an additional proportional-integral-derivative feedback loop configured to maintain open-circuit conditions while scanning. Alternating with short-circuit current mapping efficiently provides complementary insight into the highly microstructurally sensitive local and ensemble photovoltaic performance. Furthermore, direct open-circuit voltage mapping is compatible with tomographic AFM, which additionally leverages gradual nanoscale milling by the AFM probe essentially for serial sectioning. The two-dimensional and three-dimensional results for CdTe solar cells during in situ illumination reveal local to mesoscale contributions to PV performance based on the order of magnitude variations in photovoltaic properties with distinct grains, at grain boundaries, and for sub-granular planar defects.

scholarly journals Effects of Different Doping Ratio of Cu Doped CdS on QDSCs Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-4
Author(s):  
Xiaojun Zhu ◽  
Xiaoping Zou ◽  
Hongquan Zhou
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Sensitized Solar Cells ◽  
Doping Ratio

We use the successive ionic layer adsorption and reaction (SILAR) method for the preparation of quantum dot sensitized solar cells, to improve the performance of solar cells by doping quantum dots. We tested the UV-Vis absorption spectrum of undoped CdS QDSCs and Cu doped CdS QDSCs with different doping ratios. The doping ratios of copper were 1 : 100, 1 : 500, and 1 : 1000, respectively. The experimental results show that, under the same SILAR cycle number, Cu doped CdS quantum dot sensitized solar cells have higher open circuit voltage, short circuit current density photoelectric conversion efficiency than undoped CdS quantum dots sensitized solar cells. Refinement of Cu doping ratio are 1 : 10, 1 : 100, 1 : 200, 1 : 500, and 1 : 1000. When the proportion of Cu and CdS is 1 : 10, all the parameters of the QDSCs reach the minimum value, and, with the decrease of the proportion, the short circuit current density, open circuit voltage, and the photoelectric conversion efficiency are all increased. When proportion is 1 : 500, all parameters reach the maximum values. While with further reduction of the doping ratio of Cu, the parameters of QDSCs have a decline tendency. The results showed that, in a certain range, the lower the doping ratio of Cu, the better the performance of quantum dot sensitized solar cell.

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

2013 ◽  
Vol 665 ◽  
pp. 330-335 ◽  
Author(s):  
Ripal Parmar ◽  
Dipak Sahay ◽  
R.J. Pathak ◽  
R.K. Shah
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Energy ◽  
Open Circuit ◽  
Cell Parameters ◽  
Photoelectrochemical Solar Cell ◽  
Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

Sign in / Sign up

Export Citation Format

Share Document