Fault location method using measurements of differential relays for parallel transmission lines with series capacitor compensation at both ends

2012 ◽  
Author(s):  
M. Saha ◽  
J. Izykowski ◽  
E. Rosolowski
Keyword(s):  
Transmission Lines ◽  
Fault Location ◽  
Parallel Transmission ◽  
Location Method ◽  
Series Capacitor Compensation ◽  
Series Capacitor

A Novel Fault-location Method for HVDC Transmission Lines Based on Concentric Relaxation Principle and Wavelet Packet

2020 ◽  
Vol 13 (5) ◽  
pp. 705-716
Author(s):  
Congshan Li ◽  
Ping He ◽  
Feng Wang ◽  
Cunxiang Yang ◽  
Yukun Tao ◽  
...  
Keyword(s):  
Transmission Lines ◽  
Traveling Wave ◽  
Fault Location ◽  
Wave Attenuation ◽  
Wavelet Packet ◽  
Low Frequency ◽  
Evaluation Process ◽  
Location Method ◽  
Hvdc Transmission ◽  
Instantaneous Energy

Background: A novel fault location method of HVDC transmission line based on a concentric relaxation principle is proposed in this paper. Methods: Due to the different position of fault, the instantaneous energy measured from rectifier and inverter are different, and the ratio k between them is the relationship to the fault location d. Through the analysis of amplitude-frequency characteristics, we found that the wave attenuation characteristic of low frequency in the traveling wave is stable, and the amplitude of energy is larger, so we get the instantaneous energy ratio by using the low-frequency data. By using the method of wavelet packet decomposition, the voltage traveling wave signal was decomposed. Results: Finally, calculate the value k. By using the data fitting, the relative function of k and d can be got, that is the fault location function. Conclusion: After an exhaustive evaluation process considering different fault locations, fault resistances, and noise on the unipolar DC transmission system, four-machine two-area AC/DC parallel system, and an actual complex grid, the method presented here showed a very accurate and robust behavior.

scholarly journals A Novel Single-Terminal Fault Location Method for AC Transmission Lines in a MMC-HVDC-Based AC/DC Hybrid System

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 2066 ◽  
Author(s):  
Shimin Xue ◽  
Junchi Lu ◽  
Chong Liu ◽  
Yabing Sun ◽  
Baibing Liu ◽  
...  
Keyword(s):  
Transmission Lines ◽  
Fault Location ◽  
Control Strategies ◽  
Linear Regression Analysis ◽  
Location Method ◽  
Fault Resistance ◽  
Ac Networks ◽  
Minimum Residual ◽  
Ac Transmission ◽  
Location Methods

Accurate and reliable fault location method for alternating current (AC) transmission lines is essential to the fault recovery. MMC-based converter brings exclusive non-linear characteristics to AC networks under single-phase-to-ground faults, thus influencing the performance of the fault location method. Fault characteristics are related to the control strategies of the converter. However, the existing fault location methods do not take the control strategies into account, with further study being required to solve this problem. The influence of the control strategies to the fault compound sequence network is analyzed in this paper first. Then, a unique boundary condition that the fault voltage and negative-sequence fault current merely meet the direct proportion linear relationship at the fault point, is derived. Based on these, a unary linear regression analysis is performed, and the fault can be located according to the minimum residual sum function principle. The effectiveness of the proposed method is verified by PSCAD/EMTDC simulation platform. A large number of simulation results are used to verify the advantages on sampling frequency, fault resistance, and fault distance. More importantly, it provides a higher ranging precision and has extensive applicability.

scholarly journals Extending the Application of One-Terminal Fault Location Method Available in Actual Time Domain Relay

2020 ◽  
Author(s):  
Gustavo A. Cunha ◽  
Felipe V. Lopes ◽  
Tiago H. Honorato
Keyword(s):  
Transmission Lines ◽  
Time Domain ◽  
Traveling Wave ◽  
Fault Location ◽  
Reflected Waves ◽  
Location Method ◽  
Actual Time ◽  
The One

Traveling wave-based fault location has attracted more and more attention from industries worldwide. This theory allowed the implementation of functions in order to increase the reliability of the obtained fault location results. Among existing functions, the classical one-terminal method requires the detection of the wave reflected from the fault, which is still considered a challenging task. A commercial relay was released with a function able to identify these reflected waves by evaluating patterns and weighted hypotheses, identifying the wavefront most likely to be the one re ected from the fault. However, as this function is embedded into a relay, it is not possible to change the method settings. Thus, this paper presents a validation of this function which is implemented externally to the relay. Besides, its application is extended for transmission lines to which the relay can not be applied, such as huge HVDC lines.

Sign in / Sign up

Export Citation Format

Share Document