Advances in in situ and ex situ tar reforming with biochar catalysts for clean energy production

2018 ◽  
Vol 2 (2) ◽  
pp. 326-344 ◽  
Author(s):  
Yafei Shen ◽  
Yuhong Fu
Keyword(s):  
Energy Production ◽  
Clean Energy ◽  
Heterogeneous Reactions ◽  
Ex Situ ◽  
Homogeneous And Heterogeneous Reactions ◽  
Biomass Tar ◽  
Tar Reforming

Homogeneous and heterogeneous reactions can occur in the process of in situ or ex situ biomass tar reforming with biochar catalysts.

scholarly journals Biologická konverze energeticky bohatých plynů na biometan

Entecho ◽  
2021 ◽  
Vol 4 (1) ◽  
pp. 1-9
Author(s):  
Eva-Žofie Hlinková ◽  
Zdeněk Varga ◽  
Jana Zábranská
Keyword(s):  
Carbon Dioxide ◽  
Energy Production ◽  
Anaerobic Fermentation ◽  
Ex Situ ◽  
Direct Introduction ◽  
Pilot Model ◽  
In Situ Method ◽  
Global Increase ◽  
Laboratory Models

Přechod ze stávajících neobnovitelných zdrojů elektrické energie na zdroje obnovitelné se jeví jako vhodné řešení pro celosvětově narůstající spotřebu energie. Udržitelná technologie pro zpracování organických odpadů formou anaerobní fermentace produkuje bioplyn, z kterého se odstraněním oxidu uhličitého získává biometan – energeticky bohatý plyn kompatibilní se zemním plynem a využitelný jako biopalivo. Zaváděním externího vodíku, získaného z přebytečné energie z obnovitelných zdrojů, do procesu anaerobní fermentace dochází pomocí hydrogenotrofních metanogenů k redukci oxidu uhličitého na metan, čímž se zvyšuje výhřevnost bioplynu v ideálním případě až na biometan. V rámci této práce byla zkoumána technologie obohacování bioplynu pomocí vodíku přímým zaváděním do fermentoru tzv. metoda in-situ a s využitím externího bioreaktoru tzv. metoda ex-situ Získané výsledky z provozu laboratorních modelů insitu a ex-situ bioreaktoru poslouží k sestrojení poloprovozního modelu této technologie pro následné převedení do praxe. Abstract - EN The transition from existing sources of electricity to renewables seems to be a suitable solution for the global increase of energy consumption. Sustainable technology of anaerobic fermentation for the treatment of organic wastes produces biogas, from which is by removing carbon dioxide obtained biomethane – energy-rich gas compatible with natural gas and can be used as biofuel. Hydrogen obtained by using excess energy production from renewable sources, can be introduce into the anaerobic fermentation process. Hydrogenotrophic methanogens use external hydrogen for reduction of carbon dioxide to methane, which increases energetical potencial of biogas, ideally up to the level of biomethane. In this work, the technology of enrichment of biogas with hydrogen by direct introduction into the fermenter, the “in-situ” method and with the use of an external bioreactor, the “ex-situ method,” was investigated. The results obtained from the operation of laboratory models of insitu and ex-situ bioreactors will be used to build a pilot model of this technology for subsequent implementation in practice.

scholarly journals Evolution of Char Structure During In-Situ Biomass Tar Reforming: Importance of the Coupling Effect Among the Physical-Chemical Structure of Char-Based Catalysts

Catalysts ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 711 ◽  
Author(s):  
Yu Zhang ◽  
Dongdong Feng ◽  
Yijun Zhao ◽  
Heming Dong ◽  
Guozhang Chang ◽  
...  
Keyword(s):  
Pore Structure ◽  
Fluidized Bed ◽  
Chemical Structure ◽  
Coupling Effect ◽  
Coal Char ◽  
Physical Chemical ◽  
Biomass Tar ◽  
Specific Reactivity ◽  
Tar Reforming

In order to illustrate the importance of a coupling effect in the physical-chemical structure of char-based catalysts on in-situ biomass tar reforming, three typical char-based catalysts (graphite, Zhundong coal char, and sawdust biochar) were studied in the fixed-bed/fluidized-bed reactor. The physical-chemical properties of carbon-based catalysts associated with their catalytic abilities were characterized by inductively coupled plasma-atomic emission spectroscopy (ICP-AES), Raman, X-ray photoelectron spectroscopy (XPS), scanning electron microscope–energy dispersive spectrometer (SEM-EDS) and N2 adsorption. The relationship between the specific reactivity and tar reforming ability of carbon-based catalysts was discussed through a micro fluidized bed reaction analyzer (MFBRA–MR). The results indicate that the char-based catalyst has a certain removal ability for in-situ biomass tar of corn straw in an inert atmosphere, which is as follows: sawdust biochar > Zhundong (ZD) coal char > graphite. During the in-situ tar reforming, the alkali and alkaline earth metal species (AAEMs) act as adsorption/reaction sites, affecting the evolution of the aromatic ring structure and oxygen-containing functional groups of the char-based catalyst, and also its pore structure. AAEM species on the surface of char-based catalysts are the active sites for tar reforming, which promotes the increase of active intermediates (C-O bond and C-O-AAEMs), and enhances the interactions between char-based catalysts and biomass tar. The abundant AAEMs may lead to the conversion of O=C–O and C=O to C–O. For tar reforming, the internal pore structure of char-based catalysts is little changed, mainly with the carbon deposit forming on the surface pore structure. The carbon deposit from the reformation of straw tar on the char surface has better reactivity than the inherent carbon structure of ZD coal char and sawdust biochar. There is a positive relationship between the MFBRA–MR specific reactivity and tar catalytic reforming ability of char-based catalysts (decided by the coupling effect in their physical-chemical structure), which can be used to determine the catalytic ability of char-based catalysts on tar reforming directly.

Mechanism of in-situ dynamic catalysis and selective deactivation of H2O-activated biochar for biomass tar reforming

Fuel ◽  
2020 ◽  
Vol 279 ◽  
pp. 118450 ◽  
Author(s):  
Dongdong Feng ◽  
Yu Zhang ◽  
Yijun Zhao ◽  
Shaozeng Sun ◽  
Jiangquan Wu ◽  
...  
Keyword(s):  
Activated Biochar ◽  
Biomass Tar ◽  
Tar Reforming

An in situ and ex situ TEM study of the formation of thin cobalt silicide films by molecular beam epitaxy on the silicon (100) surface

1988 ◽  
Vol 46 ◽  
pp. 884-885
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove ◽  
R. T. Tung
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Defect Density ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Metal Base ◽  
In Situ Experiments ◽  
Potential Applications

The cobalt disilicide/silicon system has potential applications as a metal-base and as a permeable-base transistor. Although thin, low defect density, films of CoSi2 on Si(111) have been successfully grown, there are reasons to believe that Si(100)/CoSi2 may be better suited to the transmission of electrons at the silicon/silicide interface than Si(111)/CoSi2. A TEM study of the formation of CoSi2 on Si(100) is therefore being conducted. We have previously reported TEM observations on Si(111)/CoSi2 grown both in situ, in an ultra high vacuum (UHV) TEM and ex situ, in a conventional Molecular Beam Epitaxy system.The procedures used for the MBE growth have been described elsewhere. In situ experiments were performed in a JEOL 200CX electron microscope, extensively modified to give a vacuum of better than 10-9 T in the specimen region and the capacity to do in situ sample heating and deposition. Cobalt was deposited onto clean Si(100) samples by thermal evaporation from cobalt-coated Ta filaments.

The use of transmission and analytical electron microscopy in studying reactions and phase transformations in thin film

1993 ◽  
Vol 51 ◽  
pp. 842-843
Author(s):  
K. Barmak
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Phase Transformations ◽  
Analytical Electron Microscopy ◽  
Ex Situ ◽  
Multilayer Thin Films ◽  
Absolute Concentration ◽  
Analytical Electron ◽  
Deposition Step

Generally, processing of thin films involves several annealing steps in addition to the deposition step. During the annealing steps, diffusion, transformations and reactions take place. In this paper, examples of the use of TEM and AEM for ex situ and in situ studies of reactions and phase transformations in thin films will be presented.The ex situ studies were carried out on Nb/Al multilayer thin films annealed to different stages of reaction. Figure 1 shows a multilayer with dNb = 383 and dAl = 117 nm annealed at 750°C for 4 hours. As can be seen in the micrograph, there are four phases, Nb/Nb3-xAl/Nb2-xAl/NbAl3, present in the film at this stage of the reaction. The composition of each of the four regions marked 1-4 was obtained by EDX analysis. The absolute concentration in each region could not be determined due to the lack of thickness and geometry parameters that were required to make the necessary absorption and fluorescence corrections.

Transmission Electron Microscopy of Epitaxial silicides grown by ultra high vacuum deposition

1989 ◽  
Vol 47 ◽  
pp. 462-463
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
High Vacuum ◽  
High Energy ◽  
Energy Electron ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Transmission Electron

The silicides CoSi2 and NiSi2 are both metallic with the fee flourite structure and lattice constants which are close to silicon (1.2% and 0.6% smaller at room temperature respectively) Consequently epitaxial cobalt and nickel disilicide can be grown on silicon. If these layers are formed by ultra high vacuum (UHV) deposition (also known as molecular beam epitaxy or MBE) their thickness can be controlled to within a few monolayers. Such ultrathin metal/silicon systems have many potential applications: for example electronic devices based on ballistic transport. They also provide a model system to study the properties of heterointerfaces. In this work we will discuss results obtained using in situ and ex situ transmission electron microscopy (TEM).In situ TEM is suited to the study of MBE growth for several reasons. It offers high spatial resolution and the ability to penetrate many monolayers of material. This is in contrast to the techniques which are usually employed for in situ measurements in MBE, for example low energy electron diffraction (LEED) and reflection high energy electron diffraction (RHEED), which are both sensitive to only a few monolayers at the surface.

Atomic Layer Deposition of LiF and Lithium Ion Conducting (AlF3)(LiF)x Alloys Using Trimethylaluminum, Lithium Hexamethyldisilazide and Hydrogen Fluoride

2017 ◽  
Author(s):  
Younghee Lee ◽  
Daniela M. Piper ◽  
Andrew S. Cavanagh ◽  
Matthias J. Young ◽  
Se-Hee Lee ◽  
...  
Keyword(s):  
Lithium Ion ◽  
Atomic Layer ◽  
Mass Gain ◽  
Alloy Film ◽  
Ex Situ ◽  
X Ray ◽  
Layer Deposition ◽  
Ion Conducting ◽  
Good Agreement

<div>Atomic layer deposition (ALD) of LiF and lithium ion conducting (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloys was developed using trimethylaluminum, lithium hexamethyldisilazide (LiHMDS) and hydrogen fluoride derived from HF-pyridine solution. ALD of LiF was studied using in situ quartz crystal microbalance (QCM) and in situ quadrupole mass spectrometer (QMS) at reaction temperatures between 125°C and 250°C. A mass gain per cycle of 12 ng/(cm<sup>2</sup> cycle) was obtained from QCM measurements at 150°C and decreased at higher temperatures. QMS detected FSi(CH<sub>3</sub>)<sub>3</sub> as a reaction byproduct instead of HMDS at 150°C. LiF ALD showed self-limiting behavior. Ex situ measurements using X-ray reflectivity (XRR) and spectroscopic ellipsometry (SE) showed a growth rate of 0.5-0.6 Å/cycle, in good agreement with the in situ QCM measurements.</div><div>ALD of lithium ion conducting (AlF3)(LiF)x alloys was also demonstrated using in situ QCM and in situ QMS at reaction temperatures at 150°C A mass gain per sequence of 22 ng/(cm<sup>2</sup> cycle) was obtained from QCM measurements at 150°C. Ex situ measurements using XRR and SE showed a linear growth rate of 0.9 Å/sequence, in good agreement with the in situ QCM measurements. Stoichiometry between AlF<sub>3</sub> and LiF by QCM experiment was calculated to 1:2.8. XPS showed LiF film consist of lithium and fluorine. XPS also showed (AlF<sub>3</sub>)(LiF)x alloy consists of aluminum, lithium and fluorine. Carbon, oxygen, and nitrogen impurities were both below the detection limit of XPS. Grazing incidence X-ray diffraction (GIXRD) observed that LiF and (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film have crystalline structures. Inductively coupled plasma mass spectrometry (ICP-MS) and ionic chromatography revealed atomic ratio of Li:F=1:1.1 and Al:Li:F=1:2.7: 5.4 for (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film. These atomic ratios were consistent with the calculation from QCM experiments. Finally, lithium ion conductivity (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film was measured as σ = 7.5 × 10<sup>-6</sup> S/cm.</div>

A New Method of Wafer Level Plan View TEM Sample Preparation by DualBeam

2008 ◽  
Author(s):  
Hyoung H. Kang ◽  
Michael A. Gribelyuk ◽  
Oliver D. Patterson ◽  
Steven B. Herschbein ◽  
Corey Senowitz
Keyword(s):  
Sample Preparation ◽  
Ex Situ ◽  
Wafer Level ◽  
Cross Sectional ◽  
Plan View ◽  
Manufacturing Line ◽  
Transmission Electron ◽  
Thin Lamella ◽  
Preparation Techniques

Abstract Cross-sectional style transmission electron microscopy (TEM) sample preparation techniques by DualBeam (SEM/FIB) systems are widely used in both laboratory and manufacturing lines with either in-situ or ex-situ lift out methods. By contrast, however, the plan view TEM sample has only been prepared in the laboratory environment, and only after breaking the wafer. This paper introduces a novel methodology for in-line, plan view TEM sample preparation at the 300mm wafer level that does not require breaking the wafer. It also presents the benefit of the technique on electrically short defects. The methodology of thin lamella TEM sample preparation for plan view work in two different tool configurations is also presented. The detailed procedure of thin lamella sample preparation is also described. In-line, full wafer plan view (S)TEM provides a quick turn around solution for defect analysis in the manufacturing line.

Sign in / Sign up

Export Citation Format

Share Document