Application of response surface methodology for investigation of membrane fouling behaviours in microalgal membrane bioreactor: the effect of aeration rate and biomass concentration

RSC Advances ◽  
2016 ◽  
Vol 6 (112) ◽  
pp. 111182-111189 ◽  
Author(s):  
Atefeh Alipourzadeh ◽  
Mohammad Reza Mehrnia ◽  
Ahmad Hallaj Sani ◽  
Azadeh Babaei
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Biomass Concentration ◽  
Aeration Rate ◽  
Submerged Membrane Bioreactor

This study was performed to investigate membrane fouling phenomena and to optimize fouling parameters in a submerged membrane bioreactor.

Effect of Suspended Carriers on Extracellular Polymeric Substances in MBR

2014 ◽  
Vol 955-959 ◽  
pp. 1939-1943
Author(s):  
Chun Hua Zhang ◽  
Xiao Xia Ou ◽  
Feng Jie Zhang
Keyword(s):  
Activated Sludge ◽  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Extracellular Polymeric Substances ◽  
Aeration Rate ◽  
Woven Fabric ◽  
Membrane Model ◽  
Synthetic Wastewater ◽  
Model Surface ◽  
Submerged Membrane Bioreactor

Suspended carriers were added into a submerged membrane bioreactor (SMBR) using polypropylene non-woven fabric (PP NWF) as membrane model to treat synthetic wastewater. The changes of EPSSEPSB and EPS in activated sludge mixing liquid of MBR and in sludge on membrane model surface were researched at different aeration rate. The results showed that adding suspended carriers in MBR can increase the concentration of EPSS and EPSB in activated sludge mixing liquid, but the effect on EPSS and EPSB in the sludge on membrane model surface is related to aeration rate. Adding suspended carriers can increase the concentration of EPSS and EPSB in the sludge on membrane model surface at 0.10m3/h of aeration rate; the concentration of EPSS and EPSB in the sludge with suspended carriers is reduced when aeration rate is increased to 0.25m3/h. The study on the effect of aeration rate on EPS in sludge mixing liquid of MBR and in sludge on membrane model surface showed that an optimized aeration rate exists if suspended carriers are added to control MBR membrane fouling. At the optimized aeration rate, membrane fouling can be mitigated and controled effectively.

A venturi device reduces membrane fouling in a submerged membrane bioreactor

2016 ◽  
Vol 74 (1) ◽  
pp. 147-156 ◽  
Author(s):  
Necati Kayaalp ◽  
Gokmen Ozturkmen
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Membrane Surface ◽  
Oxygen Transfer Rate ◽  
Surface Cleaning ◽  
Aeration Rate ◽  
Transmembrane Pressure ◽  
Submerged Membrane Bioreactor ◽  
System A ◽  
Do Concentration

In this study, for the first time, a venturi device was integrated into a submerged membrane bioreactor (MBR) to improve membrane surface cleaning and bioreactor oxygenation. The performances of a blower and the venturi device were compared in terms of membrane fouling and bioreactor oxygenation. Upon comparing membrane fouling, the performances were similar for a low operation flux (18 L/m2.h); however, at a medium flux (32 L/m2.h), the venturi system operated 3.4 times longer than the blower system, and the final transmembrane pressure was one-third that of the blower system. At the highest flux studied (50 L/m2.h), the venturi system operated 5.4 times longer than the blower system. The most notable advantage of using a venturi device was that the dissolved oxygen (DO) concentration of the MBR was in the range of 7 to 8 mg/L at a 3 L/min aeration rate, while the DO concentration of the MBR was inadequate (a maximum of 0.29 mg/L) in the blower system. A clean water oxygenation test at a 3 L/min aeration rate indicated that the standard oxygen transfer rate for the venturi system was 9.5 times higher than that of the blower system.

scholarly journals Optimizing of Microalgae Scenedesmus sp. Biomass Production in Wet Market Wastewater Using Response Surface Methodology

2021 ◽  
Vol 13 (4) ◽  
pp. 2216
Author(s):  
Najeeha Mohd Apandi ◽  
Mimi Suliza Muhamad ◽  
Radin Maya Saphira Radin Mohamed ◽  
Norshuhaila Mohamed Sunar ◽  
Adel Al-Gheethi ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Biomass Yield ◽  
Biomass Productivity ◽  
Maximum Growth ◽  
Maximum Growth Rate ◽  
Aeration Rate ◽  
Composition Analysis ◽  
Wet Market ◽  
Central Composite

The present study aimed to optimize the production of Scenedesmus sp. biomass during the phycoremediation process. The biomass productivity was optimized using face centred central composite design (FCCCD) in response surface methodology (RSM) as a function of two independent variables that included wet market wastewater concentrations (A) with a range of 10% to 75% and aeration rate (B) with a range of 0.02 to 4.0 L/min. The results revealed that the highest biomass productivity (73 mg/L/d) and maximum growth rate (1.19 day−1) was achieved with the 64.26% of (A) and 3.08 L/min of (B). The GC-MS composition analysis of the biomass yield extract revealed that the major compounds are hexadecane (25%), glaucine (16.2%), and phytol (8.33%). The presence of these compounds suggests that WMW has the potential to be used as a production medium for Scenedesmus sp. Biomass, which has several applications in the pharmaceutical and chemical industry.

Sign in / Sign up

Export Citation Format

Share Document