Effect of particle size on anti-oxidation property of mullite coating prepared by pulse arc discharge deposition

RSC Advances ◽  
2015 ◽  
Vol 5 (125) ◽  
pp. 103744-103751
Author(s):  
Huang Jianfeng ◽  
Zhang Bo ◽  
OuYang Haibo ◽  
Cao Liyun ◽  
Li Cuiyan ◽  
...  
Keyword(s):  
Particle Size ◽  
Arc Discharge ◽  
Particle Sizes ◽  
Mullite Coating ◽  
Mullite Coatings ◽  
Effect Of Particle Size ◽  
Sic Composites

Mullite coatings with different particle sizes were prepared on carbon/carbon (C/C)–SiC composites surface by pulse arc discharge deposition (PADD).

Effect of Particle Size on the Oil Yield and Catechin Compound Using Accelerated Solvent Extraction

2013 ◽  
Vol 60 (1) ◽  
Author(s):  
Mohd Azizi Che Yunus ◽  
Manzurudin Hasan ◽  
Norasikin Othman ◽  
Siti Hamidah Mohd-Setapar ◽  
Liza Md.-Salleh ◽  
...  
Keyword(s):  
Particle Size ◽  
Solvent Extraction ◽  
Accelerated Solvent Extraction ◽  
Extraction Time ◽  
Oil Yield ◽  
Particle Sizes ◽  
Experimental Range ◽  
Areca Catechu ◽  
Effect Of Particle Size ◽  
Extraction Cycle

Kajian ini bertujuan untuk mengkaji kesan saiz zarah ke atas pengekstrakan sebatian catechin daripada biji Areca catechu L. dengan menggunakan Pengekstrakan Pelarut Terpecut (PPT). Saiz zarah biji Areca catechu dipelbagaikan dari 75 μm sehingga 500 μm. Pengekstrakan telah dijalankan padaparameter tetap iaitu suhu (140oC), tekanan (1500 psi), masa (10 minit), isipadu semburan (60%) dan satu kitaran pengekstrakan, masing-masing. Hasil minyak peratusan yang lebih tinggi adalah 300 mg minyak / gram sampel (30.00% pati minyak) ditemui pada 125 μm. Walaubagaimanapun, kandungan catechin dalam pati minyak hanya 0.0375 mg catechin / gram sampel. Saiz zarah yang terbaik dalam julat uji kaji ini telah dikenal pasti pada 500 μm yang memberikan kandungan catechin yang tinggi iaitu 0.0515 mg catechin / gram sampel dari 247.5 mg minyak / gram sampel (24.75% pati minyak). Kata kunci: Saiz zarah; catechin; LC-MS-TOF; pengekstrakan pelarut terpecut The purpose of this work is to investigate the effects of particle size on the extraction of catechincompound from Areca catechu L. seeds by using Accelerated Solvent Extraction (ASE). The particle sizes of Areca catechu L. seeds are varied from 75 µm until 500 µm. The extraction is conducted at fixed parameters which are temperature (140oC), pressure (1500 psi), extraction time (10 minutes), flush volume (60%) and the static cycle is done for 1 extraction cycle respectively. Higher percentage oil yield of 300mg oil/gram of sample (30.00% oil yield) is found at 125 µm. However, the amount of catechin in oil yields is only 0.0375 mg of catechin/gram of sample. The best of particle size within the experimental range has been identified at 500 µm which gives a high content of catechin with 0.0515 mg Catechin/gram of sample from 247.5 mg oil/gram of sample (24.75% oil yield). Keywords: Particle size; catechin; LC-MS-TOF; accelerated solvent extraction

The use of hollow sphere pigments as strength additives in paper and paperboard coatings—Part 1: The predictive nature of packing models on coating properties

TAPPI Journal ◽  
2020 ◽  
Vol 19 (11) ◽  
pp. 585-593
Author(s):  
ETHAN GLOR ◽  
BRIAN EINSLA ◽  
JOHN ROPER ◽  
JIAN YANG ◽  
VALERIY GINZBURG
Keyword(s):  
Particle Size ◽  
Hollow Sphere ◽  
Particle Packing ◽  
Particle Sizes ◽  
Coating Properties ◽  
Ideal System ◽  
Thermal Paper ◽  
Effect Of Particle Size ◽  
Low Levels ◽  
Better Than

Hollow sphere pigments (HSPs) are widely used at low levels in coated paper to increase coating bulk and to provide gloss to the final sheet. However, HSPs also provide an ideal system through which one can examine the effect of pigment size and particle packing within a coating due to their unimodal and tunable particle sizes. The work presented in Part 1 and Part 2 of this study will discuss the use of blends of traditional inorganic pigments and HSPs in coating formulations across a variety of applications for improved coating strength. Part 1 of this study focuses on the theory of bimodal spherical packing and demonstrates the predictive nature of packing models on the properties of coating systems containing HSPs of two different sizes. This study also examines conditions where the model fails by examining the effect of particle size on coating strength in sytems like thermal paper basecoats where the non-HSP component has a broad particle size distribution, and how these surprising trends can be used to generate better-than-expected thermal printing performance in systems with low HSP/clay ratios. Part 2 of this study focuses on the incorporation of HSPs of different particle sizes into paperboard formulations to affect coating strength and opacity.

scholarly journals Effect of Particle Size on the HDS Activity of Molybdenum Sulfide

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
Carola Contreras ◽  
Fernanda Isquierdo ◽  
Pedro Pereira-Almao ◽  
Carlos E. Scott
Keyword(s):  
Particle Size ◽  
Heavy Oil ◽  
Molybdenum Sulfide ◽  
Vacuum Gas Oil ◽  
Particle Sizes ◽  
Heavy Oils ◽  
Gas Oil ◽  
Oil Reserves ◽  
Effect Of Particle Size

More than half of the total world oil reserves are heavy oil, extra heavy oil, and bitumen; however their catalytic conversion to more valuable products is challenging. The use of submicronic particles or nanoparticles of catalysts suspended in the feedstock may be a viable alternative to the conversion of heavy oils at refinery level or downhole (in situ upgrading). In the present work, molybdenum sulfide (MoS2) particles with varying diameters (10000–10 nm) were prepared using polyvinylpyrrolidone as capping agent. The prepared particles were characterized by DLS, TEM, XRD, and XPS and tested in the hydrodesulfurization (HDS) of a vacuum gas oil (VGO). A correlation between particle size and activity is presented. It was found that particles with diameters around 13 nm show double the HDS activity compared with the material with micrometric particle sizes (diameter ≈ 10,000 nm).

scholarly journals EFFECT OF PARTICLE SIZE OF GROSSMAN'S CEMENT POWDER ON SETTING TIME

1998 ◽  
Vol 12 (1) ◽  
pp. 1-4 ◽  
Author(s):  
Jesus Djalma PÉCORA ◽  
Ricardo Gariba SILVA ◽  
Ricardo Novak SAVIOLI ◽  
Luis Pascoal VANSAN
Keyword(s):  
Particle Size ◽  
Powder Particle ◽  
Setting Time ◽  
Particle Sizes ◽  
Cement Powder ◽  
Effect Of Particle Size

A study was conducted on the hardening time of three Grossman's cements with different powder particle sizes (60, 100 and 150 mesh) using Specification n. 57 of the AMERICAN DENTAL ASSOCIATION1 (1983). The cement obtained from mesh 150 particles showed the longest hardening time (22 minutes), which was different when compared to mesh 60 (17 minutes) and 100 (17 minutes) particles.

scholarly journals Investigation of the Effect of Particle Size on Groundnut-Oil Solvent Extraction

2008 ◽  
Vol 31 (2) ◽  
pp. 1-13
Author(s):  
S.V. Manyele ◽  
I.F. Kahemel
Keyword(s):  
Particle Size ◽  
Solvent Extraction ◽  
Oil Recovery ◽  
Volatile Matter ◽  
Particle Sizes ◽  
Total Volatile ◽  
Groundnut Oil ◽  
Time Intervals ◽  
Effect Of Particle Size ◽  
Rate Of Extraction

An investigation of the effect of particle size on the performance of vegetable oil recovery by solvent extraction is reported. Experiments were conducted using soxhlet extractor, groundnuts and n-hexane. Samples were grouped into mean particle sizes of 0.25, 0.75, 1.3, 3.3, and 7.5 mm using standard sieves. The effect of particle size was studied for extraction time intervals of 1, 2, 3, 4, 5 and 8 hours. The oil yield, oil recovered per kg solvent used, kg solvent lost per unit time, and the rate of extraction (kg oil recovered per hour) decreased with increasing particle size. Meanwhile, the percent of solvent recovered, the ratio of oilrecovered to the total volatile matter driven off and the kg solvent lost per kg oil recovered, increased with increasing particle size. Based on the normalization of averaged extraction-parameters, a mean particle size of 3.3 mm was observed to be the optimum size.

EXPERIMENTAL AND NUMERICAL EVALUATION OF THE EFFECT OF PARTICLE SIZE ON SLURRY EROSION PREDICTION

2020 ◽  
pp. 1-19
Author(s):  
Qiuchen Wang ◽  
Qiyu Huang ◽  
Xu Sun ◽  
Jun Zhang ◽  
Soroor Karimi ◽  
...  
Keyword(s):  
Particle Size ◽  
Exclusion Process ◽  
Local Maximum ◽  
Particle Sizes ◽  
Slurry Erosion ◽  
Carrier Fluid ◽  
Erosion Damage ◽  
Erosion Models ◽  
Effect Of Particle Size ◽  
Erosion Profiles

Abstract During petroleum production, sand particles can be entrained with the transported carrier fluid despite of any sand exclusion process and erode the inner walls of pipelines. This erosion process may even cause pipe leakage and oil spill. Therefore, investigate the regularities of erosion damage changing with particle sizes and predict erosion behavior under different sizes particles are important to pipeline safety. In this study, slurry erosion experiments are conducted using quartz particles with similar shapes and different sizes ranging from 25 micrometers to 600 micrometers to investigate the effect of particle size on erosion profiles and provide the database for evaluating models. Computational Fluid Dynamics (CFD) is used to simulate the fluid flow and track particles to obtain impact information. Erosion equations then connect the particles' impact information with erosion rate. Finally, the available mechanistic and empirical equations erosion models are evaluated by comparing predicted erosion profile with experimental data. It was found that the local maximum erosion damage increases with particle sizes although the total erosion ratio is not increasing. These changes of erosion profiles can be predicted with acceptable accuracy by available empirical erosion models when particle sizes are no less than 75 micrometers.

scholarly journals Effect of flour and sugar particle size on the properties of cookie dough and cookie

2019 ◽  
Vol 37 (No. 2) ◽  
pp. 120-127
Author(s):  
Hüseyin Boz
Keyword(s):  
Particle Size ◽  
Opposite Effect ◽  
Textural Properties ◽  
Particle Sizes ◽  
Cookie Quality ◽  
Effect Of Particle Size ◽  
Sensory Parameters ◽  
Hardness Values

The effect of particle size of flour and sugar on the physical, sensorial and textural properties of cookie dough and cookie was investigated. According to the obtained data, both the sugar particle size and the flour particle size in cookie dough affected the hardness, adhesiveness, cohesiveness and springiness of the cookie doughs and this effect was statistically at a significant level (P < 0.01). The energy and force required for the dough extrusion dropped due to the reduction in the particle size of flour, while the reduction in the particle of sugar had the opposite effect. As the sugar and flour particle sizes decreased, the colour of the cookies became darker and the L colour values decreased. While the hardness values of the cookie samples increased with the decrease in the particle size of sugar, it decreased with the decrease in the particle size of flour. It was observed that sugar and flour particle size significantly affect cookie quality in cookie production. The formulation containing sugar and flour fractions below 150 µm has received the highest score in all sensory parameters.

Effects of Particle Sizes, Wood to Cement Ratio and Chemical Additives on the Properties of Sesendok (Endospermum Diadenum) Cement-bonded Particleboard

2010 ◽  
Vol 7 (2) ◽  
pp. 57
Author(s):  
Jamaludin Kasim ◽  
Shaikh Abdul Karim Yamani ◽  
Ahmad Firdaus Mat Hedzir ◽  
Ahmad Syafiq Badrul Hisham ◽  
Mohd Arif Fikri Mohamad Adnan
Keyword(s):  
Particle Size ◽  
Sodium Silicate ◽  
Modulus Of Rupture ◽  
Particle Sizes ◽  
Thickness Swelling ◽  
Chemical Additives ◽  
Board Density ◽  
Cement Ratio ◽  
Effect Of Particle Size ◽  
Aluminium Silicate

An experimental investigation was performed to evaluate the properties of cement-bonded particleboard made from Sesendok wood. The target board density was set at a standard 1200 kg m·3• The effect of particle size, wood to cement ratio and the addition of sodium silicate and aluminium silicate on the wood cement board properties has been evaluated. A change of particle size from 1.0 mm to 2.0 mm has a significant effect on the mechanical properties, however the physical properties deteriorate. Increasing the wood to cement ratio from 1:2.25 to 1:3 decreases the modulus of rupture (MOR) by 11% and the addition of sodium silicate improves values farther by about 28% compared to the addition of aluminium silicate. The modulus of elasticity (MOE) in general increases with increasing cement content, but is not significantly affected by the addition of sodium silicate or aluminium silicate, although the addition of their mixture (sodium silicate and aluminium silicate) consistently yields greater MOE values. Water absorption and thickness swelling is significantly affected by the inclusion of additives and better values are attained using higher wood to cement ratios.

Influence of Pulse Frequency on Mullite Coatings Prepared by Pulse Arc Discharge Deposition Process and Activation Energy

2014 ◽  
Vol 809-810 ◽  
pp. 635-641
Author(s):  
Bo Zhang ◽  
Jian Feng Huang ◽  
Cui Yan Li ◽  
Li Yun Cao ◽  
Hai Bo Ouyang ◽  
...  
Keyword(s):  
Activation Energy ◽  
Arc Discharge ◽  
Deposition Process ◽  
Pulse Frequency ◽  
Deposition Kinetics ◽  
Mullite Phase ◽  
Mullite Coatings ◽  
Sic Composites ◽  
Mullite Powder ◽  
Source Materials

Mullite coatings were prepared on C/C-SiC composites surface by pulse arc discharge deposition using mullite powder as source materials. Phase composites and microstructures of the as-prepared mullite coatings were characterized by XRD and SEM. Deposition kinetics and influence of pulse frequency on the phase composites and microstructures were investigated. The results indicate that the outer layer is composed of mullite phase, density and homogeneity of the mullite coatings are achieved when the pulse frequency reaches 2000 Hz. The deposition amount of the mullite coatings also increases with increasing deposition temperature. The deposition mass of the coatings and the square root of the deposition time at different deposition temperatures according to linear relationship, and the deposition activation energy is calculated to be 32.24 kJ/mol.

Effect of Particle Size of Fully Porous-Coated (FPC) Implants on Osseointegration

2008 ◽  
Vol 47-50 ◽  
pp. 916-919 ◽  
Author(s):  
Chaiy Rungsiyakull ◽  
Qing Li ◽  
Wei Li ◽  
Richard Appleyard ◽  
Michael Swain
Keyword(s):  
Particle Size ◽  
Bone Remodelling ◽  
Equivalent Strain ◽  
Scale Model ◽  
Particle Sizes ◽  
Dental Implantation ◽  
Macro Scale ◽  
Coated Surface ◽  
Multiscale Finite Element ◽  
Effect Of Particle Size

This paper aims at providing a preliminary understanding in biomechanics with respect to the effect of the particle size of Fully Porous-Coated (FPC) dental implant on osseointegration. 2D multiscale finite element models are created for a typical dental implantation setting. Under a certain mastication force (<200N), a global response is first obtained from a macro-scale model (without considering morphological details on the coated surface), and then it is transferred to micro-scale models (with coated surface morphology details in three different particle sizes). An equivalent strain is analyzed to investigate the effect of particle size of the FPC materials on osseointegration and initiation of bone remodelling. The result reveals that increasing particle sizes has a significant effect on biomechanical and bone remodelling responses.

Sign in / Sign up

Export Citation Format

Share Document