Crystal Form of Precipitated Calcium Carbonate as influenced by Adsorbed Magnesium Ions

Nature ◽  
1966 ◽  
Vol 212 (5058) ◽  
pp. 183-184 ◽  
Author(s):  
K. DE GROOT ◽  
E. M. DUYVIS
Keyword(s):  
Calcium Carbonate ◽  
Crystal Form ◽  
Magnesium Ions ◽  
Precipitated Calcium Carbonate

A method for measuring the in-plane compressive strength and the compression behavior of coating layers

TAPPI Journal ◽  
2011 ◽  
Vol 10 (7) ◽  
pp. 29-34
Author(s):  
TEEMU PUHAKKA ◽  
ISKO KAJANTO ◽  
NINA PYKÄLÄINEN
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Calcium Carbonate ◽  
Coating Layer ◽  
Test Methods ◽  
Coating Films ◽  
Precipitated Calcium Carbonate ◽  
Coating Color ◽  
Mineral Coatings ◽  
Styrene Butadiene

Cracking at the fold is a quality defect sometimes observed in coated paper and board. Although tensile and compressive stresses occur during folding, test methods to measure the compressive strength of a coating have not been available. Our objective was to develop a method to measure the compressive strength of a coating layer and to investigate how different mineral coatings behave under compression. We used the short-span compressive strength test (SCT) to measure the in-plane compressive strength of a free coating layer. Unsupported free coating films were prepared for the measurements. Results indicate that the SCT method was suitable for measuring the in-plane compressive strength of a coating layer. Coating color formulations containing different kaolin and calcium carbonate minerals were used to study the effect of pigment particles’ shape on the compressive and tensile strengths of coatings. Latices having two different glass transition temperatures were used. Results showed that pigment particle shape influenced the strength of a coating layer. Platy clay gave better strength than spherical or needle-shaped carbonate pigments. Compressive and tensile strength decreased as a function of the amount of calcium carbonate in the coating color, particularly with precipitated calcium carbonate. We also assessed the influence of styrene-butadiene binder on the compressive strength of the coating layer, which increased with the binder level. The compressive strength of the coating layer was about three times the tensile strength.

Transjøen, a Groundwater Influenced Lake with Special Redox and Sulphate Conditions

1976 ◽  
Vol 7 (5) ◽  
pp. 307-320 ◽  
Author(s):  
G. S. Bremmeng ◽  
A. E. Kloster
Keyword(s):  
Calcium Carbonate ◽  
Chemical Composition ◽  
Lower Layer ◽  
Calcium Content ◽  
Meromictic Lake ◽  
Redox Potentials ◽  
Precipitated Calcium Carbonate

Transjøen, a lake in S.E. Norway investigated hydrographically from October 1969 to October 1971, consists of two basins, both of which are meromictic (lake with lower layer which does not participate in the periodic circulations). The lake has a large influx of groundwater of very varying chemical composition. The calcium content is high and precipitated calcium carbonate and electrolyte rich groundwater is assumed to be the main reason for the meromictic stability. The redox potentials of monimolimnion (the lower layer which does not participtate in the periodic circulation) are extremely low, but in spite of this fact the content of sulphate is high.

scholarly journals A Novel Resorbable Composite Material Containing Poly(ester-co-urethane) and Precipitated Calcium Carbonate Spherulites for Bone Augmentation—Development and Preclinical Pilot Trials

Molecules ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 102
Author(s):  
Claudia Rode ◽  
Ralf Wyrwa ◽  
Juergen Weisser ◽  
Matthias Schnabelrauch ◽  
Marijan Vučak ◽  
...  
Keyword(s):  
Composite Material ◽  
Calcium Carbonate ◽  
Bone Substitute ◽  
Pilot Trial ◽  
Carbonate Content ◽  
Precipitated Calcium Carbonate ◽  
Degradation Behaviour ◽  
Biodegradable Composite ◽  
Loss Of Mass

Polyurethanes have the potential to impart cell-relevant properties like excellent biocompatibility, high and interconnecting porosity and controlled degradability into biomaterials in a relatively simple way. In this context, a biodegradable composite material made of an isocyanate-terminated co-oligoester prepolymer and precipitated calcium carbonated spherulites (up to 60% w/w) was synthesized and investigated with regard to an application as bone substitute in dental and orthodontic application. After foaming the composite material, a predominantly interconnecting porous structure is obtained, which can be easily machined. The compressive strength of the foamed composites increases with raising calcium carbonate content and decreasing calcium carbonate particle size. When stored in an aqueous medium, there is a decrease in pressure stability of the composite, but this decrease is smaller the higher the proportion of the calcium carbonate component is. In vitro cytocompatibility studies of the foamed composites on MC3T3-E1 pre-osteoblasts revealed an excellent cytocompatibility. The in vitro degradation behaviour of foamed composite is characterised by a continuous loss of mass, which is slower with higher calcium carbonate contents. In a first pre-clinical pilot trial the foamed composite bone substitute material (fcm) was successfully evaluated in a model of vertical augmentation in an established animal model on the calvaria and on the lateral mandible of pigs.

Sign in / Sign up

Export Citation Format

Share Document