scholarly journals The Condition of Eruption Column Collapse: 2. Three-Dimensional Numerical Simulations of Eruption Column Dynamics

2018 ◽  
Vol 123 (9) ◽  
pp. 7483-7508 ◽  
Author(s):  
Takehiro Koyaguchi ◽  
Yujiro J. Suzuki ◽  
Kai Takeda ◽  
Satoshi Inagawa
Keyword(s):  
Numerical Simulations ◽  
Three Dimensional ◽  
Eruption Column ◽  
Column Collapse ◽  
Column Dynamics

scholarly journals Three-Dimensional Numerical Simulations of Twisted Stacked Tape Cables

2015 ◽  
Vol 25 (3) ◽  
pp. 1-5 ◽  
Author(s):  
Philipp A. C. Kruger ◽  
Victor M. R. Zermeno ◽  
Makoto Takayasu ◽  
Francesco Grilli
Keyword(s):  
Numerical Simulations ◽  
Three Dimensional

Flow Mixing Enhancement from Balloon Pulsations in an Intravenous Oxygenator

2004 ◽  
Vol 127 (3) ◽  
pp. 400-415 ◽  
Author(s):  
Amador M. Guzmán ◽  
Rodrigo A. Escobar ◽  
Cristina H. Amon
Keyword(s):  
Numerical Simulations ◽  
Oxygen Transfer ◽  
Fiber Bundle ◽  
Transfer Rate ◽  
Oxygen Transfer Rate ◽  
Three Dimensional ◽  
Time Dependent ◽  
Fiber Placement ◽  
Flow Mixing ◽  
Dependent Flow

Computational investigations of flow mixing and oxygen transfer characteristics in an intravenous membrane oxygenator (IMO) are performed by direct numerical simulations of the conservation of mass, momentum, and species equations. Three-dimensional computational models are developed to investigate flow-mixing and oxygen-transfer characteristics for stationary and pulsating balloons, using the spectral element method. For a stationary balloon, the effect of the fiber placement within the fiber bundle and the number of fiber rings is investigated. In a pulsating balloon, the flow mixing characteristics are determined and the oxygen transfer rate is evaluated. For a stationary balloon, numerical simulations show two well-defined flow patterns that depend on the region of the IMO device. Successive increases of the Reynolds number raise the longitudinal velocity without creating secondary flow. This characteristic is not affected by staggered or non-staggered fiber placement within the fiber bundle. For a pulsating balloon, the flow mixing is enhanced by generating a three-dimensional time-dependent flow characterized by oscillatory radial, pulsatile longitudinal, and both oscillatory and random tangential velocities. This three-dimensional flow increases the flow mixing due to an active time-dependent secondary flow, particularly around the fibers. Analytical models show the fiber bundle placement effect on the pressure gradient and flow pattern. The oxygen transport from the fiber surface to the mean flow is due to a dominant radial diffusion mechanism, for the stationary balloon. The oxygen transfer rate reaches an asymptotic behavior at relatively low Reynolds numbers. For a pulsating balloon, the time-dependent oxygen-concentration field resembles the oscillatory and wavy nature of the time-dependent flow. Sherwood number evaluations demonstrate that balloon pulsations enhance the oxygen transfer rate, even for smaller flow rates.

Flow Structures in the Tip Region for a Transonic Compressor Rotor

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Juan Du ◽  
Feng Lin ◽  
Jingyi Chen ◽  
Chaoqun Nie ◽  
Christoph Biela
Keyword(s):  
Numerical Simulations ◽  
Reference Frame ◽  
Three Dimensional ◽  
Flow Structures ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Three Dimensional Flow ◽  
Tip Leakage ◽  
Leakage Flows ◽  
Tip Leakage Flows

Numerical simulations are carried out to investigate flow structures in the tip region for an axial transonic rotor, with careful comparisons with the experimental results. The calculated performance curve and two-dimensional (2D) flow structures observed at casing, such as the shock wave, the expansion wave around the leading edge, and the tip leakage flow at peak efficiency and near-stall points, are all captured by simulation results, which agree with the experimental data well. An in-depth analysis of three-dimensional flow structures reveals three features: (1) there exists an interface between the incoming main flow and the tip leakage flow, (2) in this rotor the tip leakage flows along the blade chord can be divided into at least two parts according to the blade loading distribution, and (3) each part plays a different role on the stall inception mechanism in the leakage flow dominated region. A model of three-dimensional flow structures of tip leakage flow is thus proposed accordingly. In the second half of this paper, the unsteady features of the tip leakage flows, which emerge at the operating points close to stall, are presented and validated with experiment observations. The numerical results in the rotor relative reference frame are first converted to the casing absolute reference frame before compared with the measurements in experiments. It is found that the main frequency components of simulation at absolute reference frame match well with those measured in the experiments. The mechanism of the unsteadiness and its significance to stability enhancement design are then discussed based on the details of the flow field obtained through numerical simulations.

Sign in / Sign up

Export Citation Format

Share Document