The Enthalpy and Heat Capacity of Magnesium and of Type 430 Stainless Steel from 700 to 1100°K.

1955 ◽  
Vol 77 (20) ◽  
pp. 5293-5293 ◽  
Author(s):  
Daniel R. Stull ◽  
Richard A. McDonald
Keyword(s):  
Heat Capacity ◽  
Stainless Steel ◽  
430 Stainless Steel

Microstructure and wear of FeCrC, SiC and B4C coated AISI 430 stainless steel

2019 ◽  
Vol 61 (2) ◽  
pp. 173-178 ◽  
Author(s):  
Ali Kaya Gür ◽  
Tülay Yildiz ◽  
Nida Kati ◽  
Sinan Kaya
Keyword(s):  
Stainless Steel ◽  
430 Stainless Steel ◽  
Aisi 430

Microstructure, anisotropy and formability evolution of an annealed AISI 430 stainless steel sheets

2021 ◽  
Author(s):  
Roberto Iquilio Abarzúa ◽  
Eliseo Hernández Duran ◽  
Tuan Nguyen-Minh ◽  
Leo A.I. Kestens ◽  
José Luis Valín Rivera ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Steel Sheets ◽  
430 Stainless Steel ◽  
Aisi 430

On the Effect of Crosshead Velocity on Polycrystalline Flow During Tension Testing of a 430 Stainless Steel

2015 ◽  
pp. 129-136
Author(s):  
Elizabeth Garfias-García ◽  
Juan Daniel Muñoz-Andrade ◽  
Pablo Gerardo Rodríguez-López ◽  
Miriam Aguilar-Sánchez ◽  
Benjamín Vargas-Arista
Keyword(s):  
Stainless Steel ◽  
430 Stainless Steel ◽  
Tension Testing ◽  
Crosshead Velocity

Cyclone Maintenance Improvement via Special Refractory Anchor Pin Studs

2004 ◽  
Author(s):  
Stephen R. Swartz
Keyword(s):  
Stainless Steel ◽  
High Temperature ◽  
Thermal Cycling ◽  
Thermal Spray ◽  
Effective Means ◽  
Protective Layer ◽  
Spray Coating ◽  
Cycle Performance ◽  
Alloy 625 ◽  
430 Stainless Steel

Since the inception of the cyclone style boiler, industry has become accustomed to performing routine maintenance during every scheduled shutdown occurring 12 months to 18 months between cycles. These maintenance cycles are influenced by service factor, loading and the type design. The same problems exist in both the standard and super critical cyclones; severe deterioration of refractory and the anchoring pin studs. This paper focuses on one type of refractory failure mechanism caused by the anchoring pin studs. Most operators have found that the most effective means of applying refractory in this type situation is to “ram” the refractory in and around the anchoring pin studs thus creating a dense lining with maximum integrity. Coupled with proper application of anchoring pin studs and a special designed coating, typical volumetric expansion of the pin studs from corrosion attack and oxidation is eliminated thus extending the life of the refractory. This mechanism is discussed along with the results of the coating performance as it relates to extreme heat oxidation and thermal cycling in laboratory tests. A protective coating was developed using a nano-cored thermal spray wire technology that produces a uniform, adherent protective layer against high temperature corrosion and oxidation. The coating yields similar thermal conductivity as a bare stud thus experiencing excellent thermal cycle performance. This specially designed thermal spray coating is applied to standard 430 stainless steel pin studs thus providing the necessary barrier against aggressive high temperature environments while maintaining excellent heat conductivity. The coating has a high amount of tungsten (40+%) in a nickel matrix with greatly reduced oxides at the substrate and throughout the coating. With these attributes for the anchoring pin studs in mind, a newly designed stud was evaluated in heat oxidation tests up to 2000°F and thermal cycling test and compared to 430 stainless steel, chromized and Alloy 625. The new stud out-performed all others even in the as-welded condition. Further corrosion testing in ferric chloride (ASTM G48) showed them to be superior to Alloy 72 and Alloy 625 in the thermal spray and welded condition. Proper welding equipment and welding techniques are also discussed since weld continuity impacts overall performance of anchoring pin studs with refractory linings. A major test site will be examined in the spring of 2004 for it’s full effectiveness in service and will be documented in order that all data retrieved would be available to the entire industry.

Texture Evolution of Ferritic (AlSl 430) Stainless Steel Strips during Cold Rolling, Annealing and Drawing

2007 ◽  
pp. 4926-4931
Author(s):  
A. Ferreira Filho ◽  
C. Herrera ◽  
Nelson Batista de Lima ◽  
R.L. Plaut ◽  
Angelo Fernando Padilha
Keyword(s):  
Stainless Steel ◽  
Cold Rolling ◽  
Texture Evolution ◽  
Steel Strips ◽  
430 Stainless Steel
Sign in / Sign up

Export Citation Format

Share Document