Modeling, Simulation, and Optimization of Postcombustion CO2 Capture for Variable Feed Concentration and Flow Rate. 1. Chemical Absorption and Membrane Processes

2012 ◽  
Vol 51 (48) ◽  
pp. 15642-15664 ◽  
Author(s):  
M. M. Faruque Hasan ◽  
Richard C. Baliban ◽  
Josephine A. Elia ◽  
Christodoulos A. Floudas
Keyword(s):  
Flow Rate ◽  
Co2 Capture ◽  
Feed Concentration ◽  
Chemical Absorption ◽  
Membrane Processes ◽  
Simulation And Optimization ◽  
Modeling Simulation

Research Trends of Carbon Dioxide Capture using Ionic Liquids and Aqueous Amine-Ionic Liquids Mixtures

2016 ◽  
Vol 13 (1) ◽  
pp. 53
Author(s):  
Siti Nabihah Jamaludin ◽  
Ruzitah Mohd Salleh
Keyword(s):  
Ionic Liquids ◽  
Co2 Capture ◽  
Membrane Separation ◽  
Carbon Dioxide Capture ◽  
Global Climate ◽  
Research Trends ◽  
Co2 Absorption ◽  
Absorption Process ◽  
Chemical Absorption ◽  
Factors Influencing

Anthropogenic CO2 emissions has led to global climate change and widely contributed to global warming since its concentration has been increasing over time. It has attracted vast attention worldwide. Currently, the different CO2 capture technologies available include absorption, solid adsorption and membrane separation. Chemical absorption technology is regarded as the most mature technology and is commercially used in the industry. However, the key challenge is to find the most efficient solvent in capturing CO2. This paper reviews several types of CO2 capture technologies and the various factors influencing the CO2 absorption process, resulting in the development of a novel solvent for CO2 capture.

scholarly journals Effects of Operating Parameters on Ionic Liquid Membrane to Remove Humidity in a Green Continuous Process

Membranes ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 65
Author(s):  
Xueru Yan ◽  
Alexandre Favard ◽  
Stéphane Anguille ◽  
Marc Bendahan ◽  
Philippe Moulin
Keyword(s):  
Ionic Liquid ◽  
Flow Rate ◽  
Continuous Process ◽  
Hybrid Process ◽  
Absolute Pressure ◽  
Mechanical Resistance ◽  
Operating Parameters ◽  
Separation Performance ◽  
Feed Concentration ◽  
Time Operation

Membrane processes are promising methods to separate gases from feed streams without phase changing. A hybrid process, the combination of ionic liquids with a ceramic membrane (ILM), has been developed for humidity removal in a green continuous process. This new concept provides a more efficient and available ionic liquid (IL)-based membrane regeneration process, which just switches the moist feed stream to dry air. Furthermore, the ILM presents high stability and mechanical resistance during long-time operation. In addition, the influences of several operating parameters, including flow rate, temperature, absolute pressure, and feed concentration on process efficiency were investigated. The lower inlet flow rate was found to be favorable for drying humid air. Moreover, when the pressure increased, the mass of absorbed water was increased, while the feed concentration had no significant effects on the membrane separation performance. However, the operating temperature had a great effect on humidity removal. It is necessary to note that the processes at room temperature can limit the energy consumption. The absorbing process of ILM remained efficient after several absorption desorption cycles. Therefore, the new ILM hybrid process that has been developed has great potential for consecutive humidity removal processes.

scholarly journals Modeling, Simulation and Optimization of Piezoelectric Bimorph Transducer for Broadband Vibration Energy Harvesting

2017 ◽  
Vol 6 (4) ◽  
pp. 5 ◽  
Author(s):  
Nan Chen ◽  
Vishwas Bedekar
Keyword(s):  
Energy Harvester ◽  
Piezoelectric Properties ◽  
Vibration Energy ◽  
Piezoelectric Bimorph ◽  
Vibration Energy Harvesting ◽  
Compliance Matrix ◽  
Simulation And Optimization ◽  
Power Characteristics ◽  
Modeling Simulation ◽  
Length Width

We demonstrate the detailed analysis for conversion of piezoelectric properties into compliance matrix and simulate a series bimorph configuration for vibration based energy generation. Commercially available software COMSOL Multiphysics was used to apply boundary conditions for optimization of geometric parameters such as length, width and thickness of piezoelectric layer to study voltage and power characteristics of the harvester. The resulting energy harvester was found to generate 1.73 mW at 53.4 Hz across a 3MW load with an energy density of 13.08mJ/cm3. We also investigated feasibility of this model by comparing it with existing experimental data of known piezoelectric ceramic compositions and found good correlation between the two.

Sign in / Sign up

Export Citation Format

Share Document