Multiphoton Photoluminescence in Hybrid Plasmon–Fiber Cavities with Au and Au@Pd Nanobipyramids: Two-Photon versus Four-Photon Processes and Rapid Quenching

ACS Photonics ◽  
2021 ◽  
Author(s):  
Qi Ai ◽  
Han Zhang ◽  
Jianfang Wang ◽  
Harald Giessen
Keyword(s):  
Rapid Quenching ◽  
Two Photon

TEM studies of amorphization processes and amorphous structures

1988 ◽  
Vol 46 ◽  
pp. 448-449
Author(s):  
T. E. Mitchell ◽  
R. B. Schwarz
Keyword(s):  
Amorphous Materials ◽  
Fission Products ◽  
Rapid Quenching ◽  
Surface Films ◽  
List Type ◽  
Oxide Glasses ◽  
Crystalline Materials ◽  
Amorphous Structures ◽  
Amorphous Surface ◽  
Interfacial Films

Traditional oxide glasses occur naturally as obsidian and can be made easily by suitable cooling histories. In the past 30 years, a variety of techniques have been discovered which amorphize normally crystalline materials such as metals. These include [1-3]:Rapid quenching from the vapor phase.Rapid quenching from the liquid phase.Electrodeposition of certain alloys, e.g. Fe-P.Oxidation of crystals to produce amorphous surface oxide layers.Interdiffusion of two pure crystalline metals.Hydrogen-induced vitrification of an intermetal1ic.Mechanical alloying and ball-milling of intermetal lie compounds.Irradiation processes of all kinds using ions, electrons, neutrons, and fission products.We offer here some general comments on the use of TEM to study these materials and give some particular examples of such studies.Thin specimens can be prepared from bulk homogeneous materials in the usual way. Most often, however, amorphous materials are in the form of surface films or interfacial films with different chemistry from the substrates.

Two-photon excitation microscopy in cellular biophysics

1995 ◽  
Vol 53 ◽  
pp. 62-63
Author(s):  
David W. Piston ◽  
Brian D. Bennett ◽  
Robert G. Summers
Keyword(s):  
Confocal Microscopy ◽  
Laser Beam ◽  
Duty Cycle ◽  
Excited Electronic State ◽  
Input Power ◽  
Two Photon ◽  
Simultaneous Absorption ◽  
Photon Excitation ◽  
Very High ◽  
Two Photon Excitation

Two-photon excitation microscopy (TPEM) provides attractive advantages over confocal microscopy for three-dimensionally resolved fluorescence imaging and photochemistry. Two-photon excitation arises from the simultaneous absorption of two photons in a single quantitized event whose probability is proportional to the square of the instantaneous intensity. For example, two red photons can cause the transition to an excited electronic state normally reached by absorption in the ultraviolet. In practice, two-photon excitation is made possible by the very high local instantaneous intensity provided by a combination of diffraction-limited focusing of a single laser beam in the microscope and the temporal concentration of 100 femtosecond pulses generated by a mode-locked laser. Resultant peak excitation intensities are 106 times greater than the CW intensities used in confocal microscopy, but the pulse duty cycle of 10-5 maintains the average input power on the order of 10 mW, only slightly greater than the power normally used in confocal microscopy.

TEM study of amorphization of Cu and Ti foils by cold-rolling

1990 ◽  
Vol 48 (4) ◽  
pp. 146-147
Author(s):  
W. A. Chiou ◽  
N. L. Jeon ◽  
Genbao Xu ◽  
M. Meshii
Keyword(s):  
Solid State ◽  
Cold Rolling ◽  
High Energy ◽  
Rapid Quenching ◽  
Vapor Condensation ◽  
Metallic Alloys ◽  
Solid State Reactions ◽  
High Energy Particle ◽  
Amorphous Metallic Alloys ◽  
Thin Foils

For many years amorphous metallic alloys have been prepared by rapid quenching techniques such as vapor condensation or melt quenching. Recently, solid-state reactions have shown to be an alternative for synthesizing amorphous metallic alloys. While solid-state amorphization by ball milling and high energy particle irradiation have been investigated extensively, the growth of amorphous phase by cold-rolling has been limited. This paper presents a morphological and structural study of amorphization of Cu and Ti foils by rolling.Samples of high purity Cu (99.999%) and Ti (99.99%) foils with a thickness of 0.025 mm were used as starting materials. These thin foils were cut to 5 cm (w) × 10 cm (1), and the surface was cleaned with acetone. A total of twenty alternatively stacked Cu and Ti foils were then rolled. Composite layers following each rolling pass were cleaned with acetone, cut into half and stacked together, and then rolled again.

Two-photon excitation fluorescence microscopy in living systems

1993 ◽  
Vol 51 ◽  
pp. 154-155 ◽  
Author(s):  
David W. Piston
Keyword(s):  
Confocal Microscopy ◽  
Fluorescence Microscopy ◽  
Singlet State ◽  
Excited Electronic State ◽  
Input Power ◽  
Two Photon ◽  
Simultaneous Absorption ◽  
Photon Excitation ◽  
Very High ◽  
Two Photon Excitation

Two-photon excitation fluorescence microscopy provides attractive advantages over confocal microscopy for three-dimensionally resolved fluorescence imaging. Two-photon excitation arises from the simultaneous absorption of two photons in a single quantitized event whose probability is proportional to the square of the instantaneous intensity. For example, two red photons can cause the transition to an excited electronic state normally reached by absorption in the ultraviolet. In our fluorescence experiments, the final excited state is the same singlet state that is populated during a conventional fluorescence experiment. Thus, the fluorophore exhibits the same emission properties (e.g. wavelength shifts, environmental sensitivity) used in typical biological microscopy studies. In practice, two-photon excitation is made possible by the very high local instantaneous intensity provided by a combination of diffraction-limited focusing of a single laser beam in the microscope and the temporal concentration of 100 femtosecond pulses generated by a mode-locked laser. Resultant peak excitation intensities are 106 times greater than the CW intensities used in confocal microscopy, but the pulse duty cycle of 10−5 maintains the average input power on the order of 10 mW, only slightly greater than the power normally used in confocal microscopy.

Microstructure of mechanically alloyed and hot-pressed Al5CuZr2

1990 ◽  
Vol 48 (4) ◽  
pp. 970-971
Author(s):  
T. E. Mitchell ◽  
P. B. Desch ◽  
R. B. Schwarz
Keyword(s):  
Mechanical Alloying ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Rapid Quenching ◽  
Hardened Steel ◽  
Alloyed Powder ◽  
Ion Milling ◽  
Mechanical Grinding ◽  
Mechanically Alloyed ◽  
Steel Container

Al3Zr has the highest melting temperature (1580°C) among the tri-aluminide intermetal1ics. When prepared by casting, Al3Zr forms in the tetragonal DO23 structure but by rapid quenching or by mechanical alloying (MA) it can also be prepared in the metastable cubic L12 structure. The L12 structure can be stabilized to at least 1300°C by the addition of copper and other elements. We report a TEM study of the microstructure of bulk Al5CuZr2 prepared by hot pressing mechanically alloyed powder.MA was performed in a Spex 800 mixer using a hardened steel container and balls and adding hexane as a surfactant. Between 1.4 and 2.4 wt.% of the hexane decomposed during MA and was incorporated into the alloy. The mechanically alloyed powders were degassed in vacuum at 900°C. They were compacted in a ram press at 900°C into fully dense samples having Vickers hardness of 1025. TEM specimens were prepared by mechanical grinding followed by ion milling at 120 K. TEM was performed on a Philips CM30 at 300kV.

Second order interference in two photon absorption

1996 ◽  
Vol 43 (9) ◽  
pp. 1765-1771 ◽  
Author(s):  
M. W. HAMILTON and D. S. ELLIOTT
Keyword(s):  
Second Order ◽  
Photon Absorption ◽  
Two Photon Absorption ◽  
Two Photon
Sign in / Sign up

Export Citation Format

Share Document